A.O. Smith SAS User manual

Front SideSize: 420 mm (W) x 297 mm (H)Red Line Mark are for Folding. Not to be Printed
Pre-instruction Literature
On Receipt
It is our policy to promote safe delivery of all orders. This product shipment has been
thoroughly checked, packed and quality certied before leaving our factory.
Visible Loss or Damage
If any of the goods called for on the bill of lading or express receipt are damaged or the
quantity is short, do not accept them until the freight or express delivery agent makes
an appropriate notation on your freight bill or receipt.
Concealed Loss or Damage
When a shipment has been delivered to you in apparent good condition, but upon
opening the packaging if any loss or damage has taken place while in transit, inform
the carrier’s agent / A. O. Smith representative immediately.
About this manual
This manual is a guide to good practice for operating and periodic maintenance of
the A. O. Smith SAS / SDS / SGS Water Heater. Do not operate the Water Heater before
reading the user manual.
Please follow instructions in this manual to ensure personal safety and proper
operation of this product. Always install, operate, inspect and maintain this product in
accordance with all applicable standards. Please store this user manual carefully for any
future reference.
Disposal of this Product
(Waste Electrical and Electronic Equipment)
This marking on the product, accessories or User Manual indicates that the product
and its electronic accessories (e.g. Remote, batteries and other replaceable electronic
accessories) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable re-use of material resources.
Household users should contact their local government oce, for details of where and
how they can take these items for environmentally safe recycling. This product and its
electronic accessories should not be mixed with other commercial wastes for disposal.
1 2
General Instructions
Safety
Your safety and the safety of your loved ones is paramount. There are several safety
related messages in this manual, which have been provided during various steps such
as the installation, operation and maintenance of your SAS / SDS / SGS Water Heater.
These messages point out potential hazards and also educate on how to reduce any
potential risks. Please always read and follow all safety messages as provided in this
user manual.
This is the safety alert symbol. This symbol alerts you to
potential hazards that can hurt you and others. All safety
messages will follow the safety alert symbol and either the
word “DANGER” or “WARNING”.
DANGER
Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury or property
damage.
WARNING
Do not use this Water Heater if any part has been under water. Immediately contact
an Authorised Service Technician to inspect the Water Heater and contact A. O. Smith
Service personnel to replace any part of the control system which has been under
water. Failure to follow this instruction can result in property damage, serious injury
or death.
IMPORTANT
These instructions have been written as a guide for the proper installation and
operation of your Water Heater. A. O. Smith will not accept any liability where these
instructions have not been followed. However, for your safety and to avoid damage
caused by improper installation, it is recommended that Water Heater must be
installed by an Authorised Service Technician.
Before proceeding with the installation instructions:
1. Inspect the Water Heater and its component parts for possible damage. Do Not
install or attempt to repair any damaged component parts. If you detect any
damage in the Water Heater, please contact the dealer where the Water Heater
was purchased or call A. O. Smith Customer Care Centre.
2. Verify that the voltage being supplied corresponds to that which is marked on the
Water Heater manual.
Key Features
Blue Diamond® Glass Lining
Blue Diamond® technology increases the life of the inner tank. The lining
is stronger and more corrosion resistant than any other in the industry.
Glass Coated Heating Element (for SDS and SGS)
Scale and sediment build-up on the surface of the element can lead
to premature failure. A. O. Smith Glass Coating helps to prevent scale
formation and extends the life of the Heating Element.
SAS has ecient Incoloy Heating Element that does not accumulate
calciferous deposits like copper.
Express Heat (for SGS)
Save your time with the help of innovative Heating Element by heating
your water 33%faster.
Temperature Control Knob
The Temperature Control Knob allows you to set the temperature
anywhere between 25ºC to 75ºC.
Long-Lasting Anode Rod
A customised alloy that works in dierent Water Conditions, protects
the tank and heating element from corrosion, has twice the lifespan
compared to a regular magnesium anode.
Multi-function Safety valve
The Multi-function Safety valve is designed to automatically relieve
pressure and discharge water in case the pressure overshoots the pre-set
limits.
Note: A. O. Smith reserves the right to amend or modify the specications and features
at any time, as and when required without any prior notication.
As compared to a regular 2 kW Water Heater.
Specications
Model SAS / SDS / SGS
Volume [L] 15 25
Power [W] SAS and SDS 2000
SGS 3000
Voltage/Frequency [V/Hz] 230~/50
Actual Stdg. Loss [kWh/24h/45°C di.] 0.410 0.505
Reheating
time for 35°C
rise [in min.]
SAS and SDS 12 22
SGS 7 16
Temperature range [°C] 25 -75*
Rated water
pressure
N/cm280
Water head (metres) 80
Inlet/Outlet connections [inch] ½ BSP
Net Weight (kgs) 9.8 13
*The maximum set temperature may vary ± 5 °C.
Dimensions
Model 15 Ltrs. 25 Ltrs.
A (mm) 373 444
B (mm) 373 444
C (mm) 100 100
D (mm) 125 125
E (mm) 130 135
F (mm) 348 383
Figure 1
A
C
B
E
F
D
Figure 2
5
2
Without Service CoverWith Service Cover
4
911
8
10
1
76
3
Part Description Part Description
1 Cold water inlet 7 Red Cap
2 Hot water outlet 8 Heating Element and Anode
3 Multi-function Safety valve 9 Thermal Cut-out
4 Temperature Control Knob 10 Thermostat
5 Decorative Front Panel
(Service Cover)
11 Wall Mount Slot
6 Blue Cap
Safety Precautions
During Installation
Do not install the Water Heater where
there is direct sunlight or rain. It is has
to be installed indoor only.
Figure 3
CAUTIO
N
Do not install the Water Heater where
water splashes on the Water Heater.
Figure 4
CAUTIO
N
Installation
Before installing, ensure the tools Adjustable wrench, Teon tape, Measuring tape,
Hammer, Bubble level indicator and Impact drill tool are available.
Mounting the Water Heater
•It is recommended as per IS 302-1 to
have 6 inches clearance from wall.
•Select a place to mount Water Heater
vertically with water connection at
the bottom.
Figure 5
Ceiling
Water
Heater
Wall
6 inch.
6 inch.
•Water Heater must be located within
3 ft. (approx.) from a 230 V electrical
outlet with proper grounding.
•Make sure that the wall can withstand
at least twice the weight of the Water
Heater when completely lled with
water.
Figure 6
3 ft.
False
Wall
Solid
Concrete
Wall
Solid
Concrete
Wall
Solid
Concrete
Wall
Solid
Concrete
Wall
3 4 5 6
*Product colour and image shown may vary from the actual product.
Part No. : 335271-070_A Date: 11-02-2020
User Manual
Water Heater
SAS / SDS / SGS
15 and 25 Litres
Installation (contd...)
•Use Mounting Template to mark holes
(Step 1).
•Use a drill bit with diameter of 10 mm
to drill 2 holes at least 60 mm deep
in the wall (Step 3). The two holes
should be aligned horizontally.
Figure 7
3
1
2
Hole
Concrete
Wall
60 mm
Drilling
Tool
Mounting
Template
80 mm
80 mm
•Insert the Expansion Anchor into the
hole (Step 1).
•Insert the Mounting screw over the
Expansion Anchor and tighten the
Mounting screw by rotating it till it
gets xed steadily (Step 2).
Figure 8
Expansion
Anchor
Hole
Mounting
screw
Concrete
Wall
Concrete
Wall
Concrete
Wall
Concrete
Wall
1
2
Mount the Water Heater on the Mounting screw through the Wall mount slot. Tug
downwards on the Water Heater to ensure that the Water Heater is xed steadily on
the Wall mount bracket.
Figure 9
Water
Heater
Wall
Water
Heater
Wall
Water
Heater
Wall Mount
Slot
Mounting
screw
Concrete
Wall
Concrete
Wall
1
2
3
ISO
9001:2015
CERTIFIED

Front SideSize: 420 mm (W) x 297 mm (H)Red Line Mark are for Folding. Not to be Printed
7
11 12 13 14
8 9 10
Plumbing instructions
Figure 10 Installation Diagram
Hot Water
Ta p
Cold Water
Ta p
*Flexible
Hose
*Flexible
Hose
Red Cap
Teflon
tape
**Multi-function
Safety valve
Discharge
Outlet
Red Cap
1
3
2
Teflon
tape
*Flexible Hoses to be procured by the customer, not part of standard product.
**Multi-function Safety valve (MFSV) comes included with the Water Heater.
1. Remove MFSV from the inlet pipe by rotating it in anti-clockwise direction.
2. Wrap the Teon tape around the inlet and outlet connections of the Water Heater to
prevent leakage.
3. Connect MFSV to the inlet pipe by hand tightening it in clockwise direction.
4. Make necessary plumbing with reference to the Installation Diagram. (Refer
“Installation Diagram”)
5. Connect the cold water pipe to the inlet [Blue Cap].
6. Connect the hot water pipe to the outlet [Red Cap].
Note:
•Make sure to connect Multi-function Safety valve to the Water Heater before
connecting inlet to the cold water tap.
•A. O. Smith recommends Nylon/ Stainless Steel (SS) braided hoses (Flexible Hoses)
having a minimum pressure rating of 8 Bar and hoses should be compatible for hot
water applications.
•The Multi-function Safety valve may drip during the usage of the heater. As the water
is heated, it expands and tries to ow back through the inlet pipe, but is prevented
by the presence of the non-return valve (an external valve provided before cold
water tap). Hence water may drip from the Multi-function Safety valve. Therefore,
Discharge outlet is provided to discharge water from the Water Heater. To avoid
dripping, it is recommended to install non-return valve at a distance of at least 40
feet away from the inlet of the Water Heater.
CAUTION
•The Multi-function Safety valve should never be removed or blocked by any
means to prevent it from dripping or releasing the excess pressure inside the
heater. Failure to do so may result in damage to the Water Heater and injuries to
the user. This will also make the warranty null and void.
•Discharge outlet is provided to release the discharge from the Water
Heater(through the Multi-function Safety valve) in case excessive pressure is
developed. The contents of the discharge from the Multi-function Safety valve
may be hot and may cause burns to the users and damage nearby objects,
therefore it is recommended to take pre-cautions while discharging water from
the Water Heater.
•It is recommended to operate the Discharge lever in the Multi-function Safety
valve on a regular basis to ensure that there are no blockages and also to remove
any lime deposits that would have been formed inside the Water Heater.
•Ensure that the Water Heater is in power OFF condition when the Discharge Lever
is being operated. Ensure that the water is lled completely in the Water Heater
before switching it ON.
•Make sure a suitable Teon tape is used for all plumbing connections to prevent
leakage.
•Use only Nylon/ Stainless Steel (SS) braided hoses (Flexible Hoses) having a
minimum pressure rating of 8 Bar and hoses should be compatible for hot water
applications.
•Failure to follow this instruction can result in property damage.
Operation
Filling the Water Heater Tank
Figure 11 1. Open a nearby hot water faucet to
permit air to escape.
2. Open the cold water inlet valve fully,
lling the Water Heater and the
piping.
3. Close hot water faucet when water
ows.
4. Check all the connections to see
if there is any leakage. In case of a
leakage, drain the water completely,
repair the leaking joint and then rell
the Water Heater.
CAUTION
•This Water Heater should not be operated with insucient amount of water.
Failure to do so may result in damage to the Water Heater and injuries to the user.
This will also make the warranty null and void.
•Once the Mounting, Multi-function Safety valve, Plumbing and Water lling is
completed, then only the power supply should be switched ON.
•Do not splash water directly or clean with benzene, pesticides, thinner, alcohol,
etc., but use a soft, dry cloth to clean the Water Heater.
Connecting to Electrical Supply
Figure 12 The power cord and plug are connected
with this Water Heater. Find a separate
socket for power plug and make sure
the socket is in rm contact with the
plug. Ensure that reliable earthing has
been done.
CAUTION
•Connect the Water Heater using independent sockets, do not use any adapters.
Use multimeter to check whether the live line and neutral line are not reverse, to
ensure complete safety.
•Before installing the Water Heater, conrm that the power of Water Heater
matches electric meter capacity and supply wire.
•The Water Heater should be earthed reliably. It is prohibited to connect the earth
wire to neutral wire or faucet water pipe.
Temperature Control Knob
Figure 13
Heating
indicator
lamp
Power
indicato
r
lamp
Switch on the Water Heater’s power supply. The Power indicator lamp glows.
Temperature Setting
Turn the Temperature control knob clockwise for the device to commence heating
and change the set temperature. The Heating indicator lamp will glow. [The set
temperature increases if the Temperature control knob is turned clockwise].
Temperature can be adjusted from 25°C to maximum 75°C. Recommended to keep
Temperature control knob notch position always in medium or above level.
Modes
There are two types of modes depending on the actual water temperature inside the
inner tank of the Water Heater:
Heating mode Standby mode
When the actual temperature of the
water is less than the set temperature, it
enters into Heating mode. The Heating
indicator lamp glows as shown in“Figure
14”.
Figure 14
After the Water Heater reaches set
temperature, it will enter into the
Standby mode due the thermostat cut-
o and the Power indicator lamp glows
and Heating indicator lamp switch o as
shown in “Figure 15” .
Figure 15
When the temperature of the water drops by 5°C from the set temperature due to
usage of water, the Water Heater again enters into the Heating mode.
Draining the Water Heater Tank
Whenever the Water Heater is not used for an extended period or if the product is
below freezing temperature, you will need to unplug the unit and drain it.
Figure 16
Discharge Outlet
Discharge Lever
1. Switch OFF the electric supply to the
Water Heater.
2. Open the hot water faucet until the
water runs cool.
3. Close cold water supply.
4. Drain the water by lifting the
Discharge Lever of the Multi-function
Safety valve upwards. (Refer“Figure
16”)
CAUTION
Please turn o the power supply to the Water Heater prior to draining the Water
Heater.
A. O. Smith Colour Match System®
Colours shown are only indicative and may vary
from actual colours available.
A. O. Smith Colour Match System® allows your Water Heater to match the colours of your
bathroom. The product of your choice comes with either white or ivory body colours,
along with the coloured front panels as in the following table.
Models SAS SDS* SGS*
Decorative front panel
(Service Cover)
White or ivory Blue or Red Red
Body Colour White or ivory White or ivory White or ivory
You have the option of changing this panel to match your bathroom decor at a nominal
cost (for SAS models).
* You have the option of changing this panel to match your bathroom decor at a no
cost. This option is available only one time after purchase (for SDS and SGS models).
Call the A. O. Smith Customer Care Centre [1800-103-2468/1860-500-2468] or visit
www.aosmithindia.com to register your product within 60 days of purchase and ask
for one of the Decorative Front Panel colour options.
Changing the Decorative Front Panel
Please follow the instructions as shown in“Figure 17”.
Figure 17
1. Pull out the Knob. 2. Unscrew the screw on
the Decorative Front
Panel.
3. Remove the Decorative
Front Panel to change.
CAUTION
•Please ensure to switch o the power supply while changing the Decorative Front
Panel and pull out the power plug from the socket.
•An insulation layer is provided below the front panel which should not be
replaced.
•While changing the front panel ensure that, none of the internal components are
damaged or removed.
DANGER
HOT
Scalding
Hot water is dangerous, especially for the young children,
aged or the disabled. The Water Heater allows you
to control the temperature of your hot water. Water
temperatures over 52°C can cause severe burns instantly or
death from scalds. Do not leave a child or an inrm person
in the bath unsupervised.
Troubleshooting
The Water Heater may not operate as desired if used incorrectly or there is a minor
cause, even though the product has no fault. In these cases, check the following issues
to solve simple problems without the help from the Customer Care Centre. If the
problem does not solve after checking the following issues, call Customer Care Centre.
Problems Possible Cause(s) Solution
Power indicator lamp and
Heating indicator lamp
does not glow.
No power supply to the
Water Heater.
Check power supply
and switch ON electrical
switch.
Thermal Cut-out has
tripped or problem in
internal wiring.
Call Customer Care
Centre.
Power indicator lamp and
Heating indicator lamp
glow but no hot water.
Heating Element
breakdown or internal
wiring error.
Call Customer Care
Centre.
Water temperature is too
high.
Improper thermostat
operation.
Call Customer Care
Centre.
Thermal Cut-out not
operating.
Call Customer Care
Centre.
Water heats slowly. Low voltage at supply
mains.
Check voltage at supply
mains.
Scale deposition. Call Customer Care
Centre.
Piping connection leaks. Connection not sealed. Re-connect piping, using
Teon tape.
Water leakage from
product.
Leakage in tank or other
parts.
Switch OFF power
immediately and Call
Customer Care Centre.
Water dripping from
Multi-function Safety
valve during heating.
Non-return valve is
installed close to the inlet
of the Water Heater.
Install Non-return valve
at a distance of at least 40
feet from the inlet of the
Water Heater (Refer page
8), if problem still persists
call Customer Care Centre.
Problems Possible Cause(s) Solution
Foul smell from hot water. Presence of organic
matter in input water.
Provide treated water at
the input.
No usage of hot water for
a long time period
If the Water Heater is not
used for an extended
period of time, drain the
water from the Water
Heater. Ensure water is
lled back before use of
Water Heater.
High electrical
conductivity of water
due to dissolved solids in
input water.
Call Customer Care
Centre. Anode options
available for highly
conductive water.
Note: Call Customer Care No. 1800-103-2468/1860-500-2468.
Circuit Diagram
Figure 18
Heating
Element
L
PE
N
Black
Thermostat
Green/Yellow
Black
Tank
Blue
Blue
White
White
Thermal cutout
Brown
Red Red
Red lightGreen light

Front SideSize: 210 mm (W) x 297 mm (H)
Warranty Terms and Conditions
Product Warranty
Your A. O. Smith Water Heater is warranted against defects arising from faulty design,
workmanship and materials for a period of 24 months from the date of the invoice,
subject to the following conditions:
1.The customer will notify the Company promptly about defects noticed and give the
Company or its Authorised Service Provider adequate opportunity to inspect, test
and remedy them, for which the customer will deposit the goods, if necessary, with
the Company’s Oce/Authorised Service Provider along with the original invoice.
2.Special warranty from the date of purchase is only applicable for the below
mentioned components:
Tank 7 Years
Glass-Coated
Heating Element
2 + 2 Years*
Product Warranty 2 Years Extended
Warranty*
4YEARS
Warranty
on tank
7YEARS
* Register your product with the A. O. Smith Customer Care Centre [1800-103-2468
/1860-500-2468] within 60 days of purchase and you will get an extended warranty on
the Heating Element [from 2 years to 4 years]. You can also get an additional changeable
Decorative Front Panel, for details refer User Manual.
3.Inspection and Test Report of the Company’s Oce/Authorised Service Provider
will be treated as nal and binding under the warranty for determining the defects,
repairs/alterations required or carried out, or certifying working of the goods
thereafter.
4.The Company or its Authorised Service Provider will be entitled to retain any
defective part replaced under the warranty.
5.The Company’s liability under the warranty will be limited only to defects which
occur under conditions of proper installation, normal operation and under proper
use. It excludes defects occurring because of abuse, faulty care or maintenance and
repairs/alterations to product or the parts by an unauthorised person.
6.The Water Heater should not be operated without water inside the tank. This will
make the warranty null and void.
7.In case of dry heating (Water Heater operated without water inside the tank), if the
Water Heater or any component of the Water Heater is damaged, then it will be
repaired/changed on a chargeable basis. After any repair or part replacement in the
Water Heater, the basic warranty continues as per the actual date of purchase.
8.The customer will have no claim under this warranty in respect of any personal
injury, damage of property or consequential damages, or for utilisation of the goods
not in accordance with the user guide.
9.The inner tank and Heating Element need to be cleaned for any deposits/scales
periodically from an Authorised Service Technician. This will ensure your Water
Heater works eciently for longer time.
10. Anode is not included under warranty, the service life of the Anode is determined
by the quality and quantity of the water owing through. If the Anode is
consumed, it needs to be replaced by an Authorised Service Technician for
ecient protection of the Water Heater. The warranty on the tank will be null and
void,
•If the Anode is removed.
•If the Anode is not replaced as and when required.
11. Warranty does not cover:
•Plastic parts.
•Cleaning of scale deposits inside Water Heater tank as a general service.
•Any damages to Water Heater occurring due to site conditions like electrical works
and plumbing works.
•Damage to Water Heater or its surroundings due to non usage of Multi-function
Safety valve, Pressure Reducing Valve or non-recommended reducing valve in
plumbing lines.
•Product installed in direct sunlight exposure or rain or non-serviceable areas (Refer
User Manual).
•Damage to Water Heater at customer house during installation or serviceable
procedures by Unauthorised Service Technician.
12. Any service related issues/replacements due to non A. O. Smith connecting hoses.
Calls which are related to the site e.g. plumbing, tap leakage, electricity etc., but
not related to the product functionality will be charged to the customer as per rate
card* (even during the warranty period).
*Refer rate card www.aosmithindia.com
1 2
Registered Oce
A. O. Smith India Water Products Private Limited
(formerly known as A. O. Smith India Water Heating Private Limited)
Plot 300, Phase - II, KIADB Industrial Area, Harohalli, Kanakapura Taluk,
Ramanagara District, Karnataka – 562 112, India.
• Customer Care No. 1800-103-2468/1860-500-2468.
• Website: www.aosmithindia.com
CIN: U31909KA2006PTC040282Part No. : 335311-008_A Date: 11-03-2019
EXPERT SERVICE
Monday to Friday: 9 a.m. to 8 p.m.
Saturday & Sunday: 9 a.m. to 6 p.m.
# For calls registered at A. O. Smith call centre before 4 p.m. only.
Available only in selected cities. For more details, please call our
Customer Care Centre or log on to www.aosmithindia.com
1800-103-2468 / 1860-500-2468
[phone] (Whats App) or
[email protected]
Water Heater
SDS / SGS
6, 10, 15 and 25 Litres
Warranty Card

Front SideSize: 210 mm (W) x 297 mm (H)
General Terms of Warranty
1.The “goods”shall mean the goods described in the purchase agreement.
2.“The customer” shall mean the original purchaser under the purchase agreement.
3.“The Company” shall mean A. O. Smith India Water Products Private Limited.
4.The “Purchase Agreement” shall mean the General Terms and Conditions of Sale
agreed upon by the customer and the Company as printed on the Invoice.
5.“Invoice”shall mean the Invoice issued for the Unit by the Company or Authorised
Dealer to the customer describing the goods and indicating, inter alia, the total
purchase price thereof, the name of the customer and the place where the goods are
to be installed.
6.“User Guide”shall mean the instructions for installation leaet published by the
Company and delivered to the customer.
Note: Follow any one for registration of the Extended Warranty.
•Call our dedicated Customer Care No. 1800-103-2468/1860-500-2468.
•To register for the warranty details of your Water Heater, visit www.aosmithindia.
com.
Post Warranty
1.The customer may be oered a yearly Service Contract at the prevailing Company
rates and terms.
2.In case the customer does not wish to enter the Service Contract, he has an option
to call our Customer Care Centre and get A. O. Smith Water Heater unit serviced
on an actual basis, i.e. by paying the Labour Cost and Spares needed to attend to
that Service or Complaint Call at the prevailing Company rates. Such service will be
rendered by the Company in towns or places where the Company has its Authorised
Service Providers.
3.In case of product repair after warranty by Authorised Service Provider, all expenses
of transporting the goods to and from the Authorised Service Provider shall be
borne by the customer directly.
4.If, during such service, it is necessary for the Company or Authorised Service Provider
to replace or repair defective components or parts, the customer shall be required to
pay for the same as per the Company’s prevailing price list.
Jurisdiction
The courts of competent jurisdiction at Kanakapura, Karnataka shall have exclusive
jurisdiction over all matters arising out of any disputes in relation to the product.
Expert Company Service - Power of 1
1.Dierent models have dierent service delivery levels.
2.Service level mentioned for particular models are applicable for metros and‘A’
Class cities, e.g. Delhi and NCR, Bengaluru, Hyderabad, Kolkata, Pune, Goa, Cochin, Chennai, Chandigarh and Ahmedabad.
3.Service level deliverables are valid up to city municipal limit only.
4.Service level may dier in case of public holidays and unavoidable conditions due to
natural calamities, any political and regional regulations.
5. Power of 1 valid service is applicable for calls registered at A. O. Smith Call Centre
before 4 p.m. only.
Customer Copy to be retained by the Customer
Dealer’s Stamp and Signature
Warranty Card
Invoice Number: ________________________________ Dated: __________________________ Unit Serial Number: __________________________________ Model: _________________________ Capacity: ______________________ Customer's Name and Address: ____________________________________________________
______________________________________________________________________________ ______________________________________________________________________________ Ph: __________________ Mobile: _____________________ E-mail: ______________________
Company Copy to be sent back to the Company
Dealer’s Stamp and Signature
Warranty Card
Invoice Number: ________________________________ Dated: __________________________ Unit Serial Number: __________________________________ Model: _________________________ Capacity: ______________________ Customer's Name and Address: ____________________________________________________
______________________________________________________________________________ ______________________________________________________________________________ Ph: __________________ Mobile: _____________________ E-mail: ______________________
3 4