A4Tech BT-630 User manual

Bluetooth Mouse User Guide
Model: BT-630
www.a4tech.com

—
1 —
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and if not installed and used in
accordance with the instruction may cause harmful interference to radio communication.
However there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can
be determined by turning the equipment off and on the user is encouraged to try to correct
the interference by one or more of the following measures:
●Reorient of relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
●Consult the dealer or an experienced radio/TV technician for help.
THE CHANGES OR MODIFICATIONS NOT E PRESSLY APPROVED BY THE PARTY

—
2 —
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received including interference that may cause
undesired operation.
FCC Radiation Exposure Statement
The equipment complies with FCC radiation exposure limits set forth for uncontrolled
equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to
OET65. The equipment has very low levels of RF energy that it is deemed to comply without
testing of specific absorption ratio (SAR).
Package Contents
1. Bluetooth Mouse
2. 1*AA Battery
3. Quick Set Up Guide
4. CD (CD User Manual)
Features
1. Bluetooth V2.0 10 meter range

—
3 —
2. 1000DPI
3. Four stages power saving mode low battery warning
4. 8 in Right software innovative 4D wheel
System Requirement : Windows XP/ Vista / Windows 7
Know your product

—
4 —
Front View
Back View
Dual-color LED Indicator
Bluetooth Mouse LED Status
Power On Green LED: Turn off after 1 Second
Low Battery Warning Red LED: Blinking
Connection Start Alternate Blink Between Red and Green
Connection Complete Stop Blinking
Turn On/Off Mouse

—
5 —
1. Slide on the power switch to immediately turn on the
mouse.
2. To turn off the mouse just slide off the power switch and
then LED light is off immediately.
Battery Installation
Open battery cover and insert the supplied AA battery. Please make sure that the positive (+)
and negative (-) ends of the battery match the polarity indicators inside the battery
compartment.
Power Saving Management
Four stages power saving mode provide the best power saving management. In Deep Sleep the
mouse can
be activated by clicking any mouse buttons. In other sleep statuses just move the mouse to
activate
it.

—
6 —
Note: The mouse will enter Deep Sleep ten seconds after turning off PC. To wake it up turn
on PC and click any mouse button.
Status Time elapses to enter the
mode Power Consumption
Way to wake up
Stand-by 0 second 20mA Moving
Slight Sleep 2 seconds 10mA Moving
Middle Sleep 4 seconds 1.7mA Moving
Deep Sleep 5 minutes 0.3mA Clicking

—
7 —
Configuration
Our Bluetooth Mouse is designed to work with Five major software standards: Microsoft
Broadcom IVT Toshiba Apple. Please select the corresponding connection way according to
your software standard.
Bluetooth
Software
Vendor
Bluetooth
Software
Name
Bluetooth
Device Not
Inserted
Bluetooth
Device
Already
Inserted
Bluetooth
Device In
Working
Support
Version
Microsoft Windows
Bluetooth
Windows
XP(SP2) Above
Broadcom Widcomm
V4.0 Above
IVT BlueSoleil
V5.0 Above
Toshiba
Bluetooth
Stack
V3.0 Above
Apple Mac OS X
Bluetooth
Mac
OS X
10.4~10.5
Above

—
8 —
Note：
：：
：Before start Bluetooth Mouse connectivity please check whether your system has
already installed Bluetooth software and whether it works.
Bluetooth Software: MICROSOFT
Step 1：Click
Start
click
Control Panel
(make sure you're in Classic View) and
then double-click Bluetooth Devices.
Step 2：In popped
Bluetooth Devices
window Click Add.

—
9 —
Step
3
：
Turn on the mouse and press the
connection button at the bottom of mouse
until the LED Indicator in the middle
wheel blinks alternately in Red and
Green. In the Add Bluetooth Device
Wizard select the My device is set up and
ready to be found check box and then
click Next.
Step 4
：
After th
e device names appear click
Bluetooth Mouse and then click Next.

—
10 —
Step 5
：
When the wizard asks to specify a
passkey click Don't use a passkey and
then click Next.
Step 6
：
Please wait while the wizard
completes the process of adding your
Bluetooth mouse. In the final page of the
wizard click Finish and then click OK.
The LED Indicator in the middle wheel
stops blinking.
Bluetooth Software: WIDCOMM

—
11 —
Step 1
：
Right click on Bluetooth icon
located at system tray then select Add a
Bluetooth Device.
Step 2：In popped
Initial Bluetooth
Configuration Wizard Click Next.
Step
3
：
Turn on the mouse and press the
connection button at the bottom of mouse
until the LED Indicator in the middle
wheel blinks alternately in Red and Green.
In Bluetooth Devices Selection it will
automatically detects discoverable
bluetooth devices.
Step 4
：
After the device names appear click
BlueTooth Mouse and then click Next.

—
12 —
Step
5
：
Please wait while the wizard completes the process of adding your Bluetooth mouse.
In the final page of the wizard click Click here. The LED Indicator in the middle wheel
stops blinking the Bluetooth mouse has successfully installed.
Bluetooth Software: BLUESOLEIL
Step 1
：
Right click on Bluetooth icon
located at system tray then select Add a
Display Classic View.
Step 2
：
Double click orange circle button to
start searching Bluetooth devices.

—
13 —
Step 3
：
Turn on the mouse and press the
connection button at the bottom of mouse
until the LED Indicator in the middle
wheel blinks alternately in Red and
Green. The mouse icon will display after
searching Bluetooth devices sucessfully.
Step 4
：
Right click on the mouse icon and
select Connect Bluetooth Human Interface
Device.

—
14 —
Step
5
：
The Bluetooth mouse will
automatically complete the connection.
The bluetooth mouse has successfully
installed while the LED Indicator in the
middle wheel stops blinking.
Bluetooth Software: Bluetooth Stack

—
15 —
Step 1
：
Right click on Bluetooth icon
located at system tray then select Add
New Connection.
Step 2：In popped
Bluetooth Settings
Click
New Connection.
Step 3
：
Turn on the mouse and press the
connection button at the bottom of mouse
until the LED Indicator in the middle
wheel blinks alternately in Red and
Green. In Add New Connection Wizard
click Express Mode and then click Next
to search Bluetooth devices.
Step 4
：
Please wait until
the device names
appear click
BlueTooth Mouse and then click Next.

—
16 —
Step 5
：
Ple
ase wait while the wizard
completes the process of adding your
Bluetooth mouse. The mouse doesn’t
require Passkey(PIN code).
Step 6
：
The LED Indicator in the middle
wheel stops blinking after the mouse has
successfully installed.
Bluetooth Software: Mac OS Bluetooth

—
17 —
Step 1
：
Right click on Bluetooth icon
located at system tray then select Set up
Bluetooth Device.
Step 2
：
Follow on
-
screen instructions to
continue setup. Select Mouse when below
window appears.
Step 3
：
Turn on the mouse and press the
connection button at the bottom of mouse
until the LED Indicator in the middle
wheel blinks alternately in Red and
Green. After device names appear click
BlueTooth Mouse and then click Next.
Step 4
：
The bluetooth m
ouse has
successfully installed while the LED
Indicator in the middle wheel stops
blinking. You can choose to set up
another device or click Quit to exit.

—
18 —
Software Installation
1. Before installing the mouse software please uninstall any previously
installed mouse
software.
2. Insert enclosed CD to start installation.
3. Follow on-screen instructions to complete the installation.
4. The icon will appear on your desktop then you have successfully installed the
software.
5. To launch the software double click the icon on your desktop or go to Start—
Programs—A4tech 8 in Right then the icon will appear in the taskbar at the right
corner of your screen.

—
19 —
.For more completed instructions on how to set up this software please refer to software
manual in CD.
** Features and specifications of all A4 TECH products are subject to change without
notification.