AAT KDA-BOLT150 User manual

Electric Bolt Lock— Installation manual
AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
All rights reserved. 1
Installation Manual
PROXIMITY CARD READER
KDH-C130U-BLACK
KDH-C130M-BLACK
KDH-CK130U-BLACK
WERSION 2.0 28-11-2018
Installation Manual
PROXIMITY CARD READER
KDH-C130U-BLACK
KDH-C130M-BLACK
KDH-CK130U-BLACK
WERSION 2.0 28-11-2018
Installation Manual
Electric Bolt Lock
KDA-BOLT150
VERSION 3.0 08-07-2020

Electric Bolt Lock — Installation manual
2 AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
All rights reserved.
DIRECTIVES .……………………………………………………………………………………. 3
SAFEGUARDS AND WARNINGS .……………………………………………………. 4
1. INTRODUCTION ……………………………………….……………………………….……… 5
2. SPECIFICATION ……………..……..……………...………………………………….….…. 5
3. CONNECTION ……………………………………………………………………………….. 5
4. PACKAGE CONTENT ……………………………………………………………………….. 5
5. DELAY SETTING ……………………………………………………………………………….. 6
6. INSTALLATION DIAGRAM ………………………………………………………………… 6
CONTENTS

Electric Bolt Lock— Installation manual
AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
All rights reserved. 3
THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE
FOLLOWING DIRECTIVES:
Direcve 2014/30/EU of the European Parliament and of the Council of 26 February
2014 on the harmonisaon of the laws of the Member States relang to electromag-
nec compability (recast) Text with EEA relevance.
Direcve 2012/19/EU of the European Parliament and of the Council of 4 July 2012
on waste electrical and electronic equipment (WEEE) Text with EEA relevance
Direcve 2011/65/EU of the European Parliament and of the Council of 8 June
2011 on the restricon of the use of certain hazardous substances in electrical and electronic
equipment Text with EEA relevance
Informaon
The device, as a part of professional intercom system used for surveillance and control, is not
designed for self-installaon in households by individuals without technical knowledge
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN US-
ER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES NOT
ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE CONTACT-
ED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS
OF SUCH AN ACTION.
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER DEVICE OP-
ERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH THE MANUAL PRIOR TO
INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER -SERVICEABLE
PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL MAY OPEN THE UNIT INSTAL-
LATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE PERSONNEL AND
SHOULD CONFORM TO ALL LOCAL REGULATIONS

Electric Bolt Lock — Installation manual
4 AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
All rights reserved.
IMPORTANT SAFEGUARDS AND WARNINGS:
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this
manual is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a
direct influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with
the user’s manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the pro-
ducer is forbidden;
7. Mounting the device on unstable surface or using not recommended mounts is forbidden.
8. Improperly mounted device may cause a fatal accident or may be seriously damaged itself.
Device must be mounted by qualified personnel with proper authorization, in accordance with
this user’s manual;
9. Device should be supplied only from a power sources whose parameters are in accordance
with those specified by the producer in the device’s technical datasheet. Therefore, it is forbid-
den to supply the device from a power sources with unknown parameters, unstable or not meet-
ing producer’s requirements;
10. Signal and power cables should be placed in a way excluding the possibility of damaging
them by accident. Special attention must be paid to cables getting from the device and connect-
ing the power supply;
11. Electric installation supplying the device should be designed to meet the specifications given
by the producer in such a way that overloading is impossible;
12. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs
should be conducted only by qualified service personnel;
13. Unplug the device from the power source immediately and contact the proper maintenance
department when the following occurs:
•Damages to the power cord or to the plug itself;
•Liquids getting inside the device or exposure to strong mechanical shock;
•Device behaves in a way not described in the manual and all adjustments approved by
the manufacturer and possible to apply by user himself, seem not to have any effect;
•Device is damaged;
•Atypical behaviour of the device components may be seen (heard).
14. In necessity of repairs attention to using only original replacement parts (with their parame-
ters in accordance with those specified by the producer) should be paid. Non-licensed service
and non-genuine replacement parts may cause fire or electrocution;
15. After maintenance activities tests should be run to ensure proper operation of all the func-
tional components of the device.

Electric Bolt Lock— Installation manual
AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
All rights reserved. 5
1. Introducon
Solenoid bolt lock with is an alternave to the electromagnec locks commonly used in access
control. In a lock of this type you will nd an electromagnet that pulls out a metal bolt while powe-
red. The door has a metal plate with a hole and a magnet. The movable bolt retracts and locks the
door when it is opposite the mounng plate.
Features
• Latest design, Low power consumpon.
• Low temperature, safe & Durable.
• Professional design, double electric current protecon.
• Protecon design, cathode and anode protecon.
• Cercaon authority, CE, MA qualied products.
Power Supply DC12V/1A
Electric Lock Power Starng state: 960mA; Normal state: 120mA
Locked Time Delay 0~9 sec can be set by jumpers
Signal Output Include N.C(0.5A) relay
Face Plate 205(L)×35(W)×42(H)mm
Cover 90(L)×25(W)×2(H)mm stainless steel
Bolt 17mm sliding stainless steel
Safety Precauons Locked when powered (fail safe)
Built-in Exit Switch Input to Unlock.
Provides reverse current protecon.
2. Specicaon
COLOR FUNCTION
Red +12V DC
Black GND
Yellow PUSH- door release buon
White Door state Signal from Reed Switch Output
Brown COM common Signal Output
Green NC Normally Closed Signal Output
Blue NO Normally Open Signal Output
3. Connecon
4. Package content
• Electric bolt lock
• Instrucon manual
• Stainless steel cover
• Mounng accessories

Electric Bolt Lock — Installation manual
6 AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
All rights reserved.
6. Installaon diagram
5. Delay seng

Electric Bolt Lock— Installation manual
AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
All rights reserved. 7
Stages of mounng the solenoid lock
1. Determine the mounng locaon of the solenoid lock and metal plate. Sck the mounng template.
2. Cut the mounng hole according to the template.
3. Mount the mounng brackets.
4. Connect the necessary cables. Place the electric lock in the mounng hole, place a sheet plug on the elec-
tric lock and screw the whole to the mounng brackets.
5. Mount the magnet mounng plate in the right place on the door leaf. The distance between the spindle
handle and the lock should be 5 to 8 mm.
Inside installaon diagram (wooden frame)

Electric Bolt Lock — Installation manual
8 AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
All rights reserved.