Abbott FreeStyle Libre 2 User manual

CODE XXX
CODE
A
b
Sensor Pack | Envase del sensor
Customer Service | Atención al clien
1-855-632-8658
XXXXXXXXXXX
XXX
YYYY-MM-DD
F
r
e
e
S
t
y
l
e
L
i
b
STEP 3
STEP 6
STEP 9
Get ReadyApply Sensor Prepare Sensor Applicator
Wash site using a plain soap,
dry, and then clean with alcohol
wipe. Allow site to air dry before
proceeding.
Peel lid completely o Sensor Pack.
Unscrew cap from Sensor Applicator.
CAUTION: Sensor codes
must match on Sensor Pack
and Sensor Applicator or
glucose readings will be
incorrect.
Refer to your User’s Manual for full System instructions and information.
Touchscreen
Home Button
USB Port
Sensor
Pack
Reader
Place Sensor Applicator over site
and push down rmly to apply
Sensor.
CAUTION: Do not push down on
Sensor Applicator until placed
over prepared site to prevent
unintended results or injury.
Make sure Sensor is secure.
Discard used Sensor Applicator
and Sensor Pack according to
local regulations.
Gently pull Sensor Applicator
away from your body.
Quick Start Guide for
FreeStyle Libre 2 Reader
STEP 1
STEP 4
STEP 7
STEP 2
STEP 5
STEP 8
Line up dark mark on Sensor
Applicator with dark mark on
Sensor Pack. On a hard surface,
press down rmly on Sensor
Applicator until it comes to a stop.
Sensor Applicator is ready to
apply Sensor.
CAUTION: Sensor Applicator
now contains a needle. Do not
touch inside Sensor Applicator
or put it back into Sensor Pack.
Lift Sensor Applicator out of
Sensor Pack.
Lid Cap
Sensor
Sensor
Applicator
Codes on labels
must match
●
1 Assemble and Apply
Sensor to your body
●
2 Start new Sensor with Reader
●
3 Check your glucose whenever you
want for up to 14 days.
Wait 60 minutes
for start-up
Select site on back of upper arm.
Do not use other sites as these may
result in inaccurate glucose readings.
Note: Avoid scars, moles, stretch
marks, lumps, and insulin injection
sites. To prevent skin irritation,
rotate sites between applications.
Setup Overview
●
1 Assemble and Apply Sensor to the back of your upper arm
FLASH GLUCOSE MONITORING SYSTEM

350
250
150
50
82
mg
dL
Glucose
Trend Arrow What it means
Glucose rising quickly
Glucose rising
Glucose changing slowly
Glucose falling
Glucose falling quickly
Glucose Going
Low
2pm 6pm 10pm
Start New
Sensor
Review
History
No Active Sensor
10:23pm
OK
Low Glucose Alarm
High Glucose Alarm
Signal Loss Alarm
Change Alarm
Settings
Change Alarm Settings
Alarm Settings
Low Glucose 70 mg/dL
High Glucose 240 mg/dL
Signal Loss On
OK
minutes
New Sensor
Starting Up
60
Sensor can be used in:
OK
Do not take high doses
of vitamin C (more than
500 mg per day). This may
falsely raise your Sensor
readings. Supplements like
Airborne®or Emergen-C®
have high doses of vitamin
C. Read labeling for all
supplements to determine
vitamin C content.
Important OK
Low Glucose Alarm
Dismiss Alarm & Check
Glucose
High Glucose Alarm
Dismiss Alarm & Check
Glucose
Scan Sensor now?
Signal Loss Alarm
YesNo
Alarms
Sound & Vibration
Time & Date
Settings
1 / 3
Check
Glucose
Review
History
Ends in 14 days
10:23pm
When any alarm is on, sound/vibration and signal status
display on the Home Screen.
Refer to User's Manual for additional symbols.
Symbol What it means
Sound and Vibration ON
Sound and Vibration OFF
Sensor communicating with Reader
Sensor not communicating with Reader
Check
Glucose
Review
History
Ends in 14 days
10:23pm
Press Home Button to turn on Reader.
Note: If using Reader for the rst
time, follow the prompts to set date
and time.
Touch Start New Sensor.
Hold Reader within 1.5 inches (4 cm) of Sensor
to scan it.
Note: Before you start your Sensor, choose
which device you want to use. If you start the
Sensor with the Reader, you will be unable to
use the App to check your glucose or receive
alarms.
Press Home Button to go to
Home Screen. Touch .
Touch Alarms and then touch
Change Alarm Settings.
Select and set your alarms. Touch done to save.
Review the important information
on the screen.
Sensor can be used to check your
glucose after 60 minutes.
Hold Reader within
1.5 inches (4 cm) of
Sensor to scan it.
Reader shows your glucose reading. This includes your
Current Glucose, Glucose Trend Arrow, and Glucose Graph.
Press Home Button to turn on Reader.
If you have followed the instructions described in the User’s Manual and are still having diculty setting
up your System or if you are not sure about a message or reading, contact your health care professional.
STEP 3
STEP 3
STEP 1
STEP 1
STEP 2
STEP 2 STEP 3
STEP 1 STEP 2
Touch Dismiss Alarm & Check
Glucose or press the Home Button to
dismiss alarm and check your glucose.
Touch No to dismiss alarm.
Touch Ye s or press the Home Button
to dismiss alarm and scan the Sensor.
Noties you when glucose
is below the level you set.
Noties you when Sensor is not
communicating with Reader
and that you are not getting
Low or High Glucose Alarms.
Noties you when glucose is
above the level you set.
The Sensor automatically communicates with the Reader and can give you glucose alarms.
Alarms are on by default. To change their settings or turn alarms o,follow these steps.
IMPORTANT: Glucose alarms are an important safety feature. Please consult your health
care professional before making changes.
You must scan your Sensor to see your glucose reading.
Current Glucose
Glucose from your latest scan
Glucose Graph
Graph of your current and
stored glucose readings
Message
Touch for more
information
The circular shape of the sensor housing, FreeStyle,
Libre, and related brand marks are marks of Abbott.
©2018-2020 Abbott ART40392-003 Rev. A 01/21
Manufacturer
Consult instructions for use
●
2 Start new Sensor with Reader
●
3 Check your glucose
Using Alarms
Setting Alarms