ABC Design Kiddie Ride On User manual

Kiddie Ride On
Kiddie Ride OnKiddie Ride On
Kiddie Ride On

Dear Customer,
Congratulations on the purchase of your ABC-Design Kiddie Ride On. We are pleased that you have chosen one of our products and
hope that you will be completely satisfied with the service you receive from the product. We advise you to read the Instruction Leaflet
carefully before use and then to keep it in a safe place. If you fail to do this the safety of your child can be jeopardised. Kindly pay
attention to the washing and care instructions so that you enjoy long and trouble free use of your new purchase.
ABC-Design Team.
Warning information
Warning informationWarning information
Warning information
-Please read this instruction carefully before using the Kiddie Ride In.
-If you do not care about the instruction your child could not be fully protected.
-If you drive through stairs or if you lift up your stroller please take away your child down from the Kiddie Ride On.
-Please make sure, that all locks are closed
-This Kiddie Ride On can only be used for one child.
-From time to time make sure, that all necessary locks are still closed careful. If not, please tighten.
-Please don´t do any changings which can lower the safety of the products.
-Please make sure, that the child can have a support from the stroller while standing on the Kiddie Ride On.
-Please only use this Kiddie Ride On on stroller which are prepared for this kind of product.
Page 2

Fixation on the stroller
Fixation on the strollerFixation on the stroller
Fixation on the stroller
Please remove the fixation from the Kiddie Ride On as shown
on the picture. Push the lever to the backside and open the
lock. Now you can easily remove the fixation.
Turn the screw(1) to the left side for opening. Now you can take
the screw away.
Page 3

Pull the plastic slope together with the screw to the outside.
Here you can see all parts of the fixation.
Page 4

Take the plastic slope as shown on the picture. Fix it at the
backside tube of the stroller.
Now take the second part of the fixation to the plastic slope.
Pull the plastic slopes to the slot and tighten the plastic slope
Page 5

Put the hull on the screw.
Now fix the screw and turn it to the right.
Page 6

Fixation on the stroller
Fixation on the strollerFixation on the stroller
Fixation on the stroller
The fixation lever of the Kiddie Ride On can be adjusted in the
width. Remove the screw (1) (turn to the left)on the lower part
of the Kiddie Ride On. Now you can adjust the fixation lever in
the width. When you have reached the final position tighten the
screw (turn to the right).
Please make sure, that both sides have the same distance and
the Kiddie Ride On is situated in the middle position.
Fix the Kiddie Ride On as shown on the picture.
Page 7

Please press the pin on both sides into the holes of the fixation.
Please make sure, that the lock is closed in the right way.
Page 8

Adjustment of
Adjustment ofAdjustment of
Adjustment of the
thethe
the Kiddie Ride On
Kiddie Ride OnKiddie Ride On
Kiddie Ride On
For adjusting the Kiddie Ride On in the length please press the
button on both sides (1)
Now you can adjust the Kiddie Ride On in the length (2).
Remove the button and the adjustment will lock.
Please adjust the Kiddie Ride On in the length, that this is
situated behind the breaks and the wheels.
Page 9

For adjusting the Kiddie Ride On in the height please press the
buttons on both sides (1).
Now you can adjust the levers in the height.
Please adjust the height, that the wheels are situated on the
floor.
If you don´t use the board, you can easily clapp it upwards.
Page 10

Removing the
Removing theRemoving the
Removing the Kiddie Ride On
Kiddie Ride OnKiddie Ride On
Kiddie Ride On
For removing the Kiddie Ride On from the stroller please
push the lever to the backside as shown on the picture to
open the lock.
Now you can remove the lever from the fixation. Take away
the Kiddie Ride On from the stroller.
You can leave the Kiddie Ride On fixation fixed at the
stroller every time.
Page 11