Abelko UltraBase20 User manual

www.abelko.se
IMSE
UltraBase20
Welcome to Ultra!
All users of this product must carefully read the manual and take
necessary safety precautions.
Safety instructions
If the product is not used as intended its protection and safety functions may
not work.
Installation
The unit is to be mounted on a DIN rail in a locked cabinet. Installation is
carried out by a qualied electrician. Cables must be fastened and secured so
that no risk for injury or re exists. Ventilation openings in the devise housing
may not be covered.
A circuit breaker shall be installed close to the unit and its power supply.
Function and position shall be clearly labelled. This must also be done for
dangerous voltages connected to built in relays. External voltage source
connected to DIGITAL OUT must be limited to a maximum of 2 A.
The equipment must be unplugged from the mains and other possibly
dangerous voltage sources during installation and service.
Quick start guide

www.abelko.se
Power supply
UltraBase20 can be powered i serveral ways. Requirements and characteristics
of the unit’s inputs and outputs can be found in the table below.
Port Supply
Supply expansion
module (port Ex)
VDC 24 VDC* (>300 mA) 24 VDC, 1A
24VAC
24 VAC (>300 mA) No
24 VDC* (>300 mA) No
* Stabilized DC voltage.
The Power LED lights up when the device is energized and the Status LED
lights up when the device has started up and is working.
Safety instructions
All external equipment connected to the device must have double or
enhanced isolation (class II) from power mains or other dangerous
voltage source (>50 VAC or > 75 VDC).
Note that all cables used must be approved for at least 50 °C
ambienttemperature.
At high ambient temperatures there is a risk for burning injuries. Wait
for the equipment to cool down, and use protective gloves.
Network connection
The unit is connected to a permanent network by the Ethernet port. The
factory default IP address is 10.0.48.94.
Local PC is used only to connect the unit directly to a PC. It has IP-address
192.168.142.1, and can be used to congure the regular network connection
in the UltraBase20.
When you use the Local PC port, the computer should be congured for DHCP
(which it usually is).
1. Open a web browser and enter the IP address https://192.168.142.1 in
the address bar. This will take you to the login page.
User name and password the rst time you log in:
User name: cong
Password: ef56
2. Go to the menu Communication and Network, and set the IP
address and netmask, in order to congure the settings for the port
marked Ethernet. You can also check the DHCP box, the unit will then

www.abelko.se
automatically get network settings. After a while, you can see which IP
address it received. You can use this IP address to access the device
from a PC, connected to the same network.
HTTPS
The rst time you log in to an Ultra, you will be warned that the connection is
not secure, or similar. This is because the HTTPS protocol ensures a secure and
encrypted connection. The security is guaranteed by a certicate, which needs
to be issued for a specic IP number. Since the IP address is and needs to be
congurable, there is no signed certicate for the unit.
You need to accept and add this exception. The procedure diers depending on
which browser you are currently using. The communication is still encrypted, so
no-one can see, for example, which passwords are being used.
Grapical programming
Graphical programming is available as an installable program. Download it at
www.abelko.se
There is also a link to the program in your units user interface under
Conguration and Graphical programming.
Analog outputs
There are four analog outputs for 0-10 V, marked AO.The gure below is an
example on how you can connect an AC-powered valve controller.
Digital outputs
There are three digital outputs, marked DIGITAL OUT. They are normally
open relays with breaking capacity of 250 VAC/2A or 30 VDC/2A with resistive
load.
Temperature sensor inputs
There are six inputs for resistive temperature sensors, marked with T. They
have a measurement range of 800 to 1600 Ohms and works for example with
PT1000 sensors (approximately -50ºC to 150ºC) and Ni1000 sensors.

www.abelko.se
Analog inputs
There are two analog inputs, marked AI. These can be congured to measure
0-10 V or 0-20 mA.
Digital inputs
There are ve digital inputs, marked DI. These can be used for digital status,
counters and frequency measurement.
Cleaning
The housing is cleaned from dust and dirt using a dry cloth. Do not use
chemicals.
Recycling
When recycling, sort UltraBase20 as electronics.
Repair and service
Reparation and service shall always be performed by Abelko Innovation.
Contact your distributor rst if the need arises.
Manuals, updates och other information are available at
www.abelko.se.