Abelko UltraBase30 User manual

www.abelko.se
IMSE
UltraBase30
Welcome to Ultra!
All users of this product must carefully read the manual and take
necessary safety precautions.
Safety instructions
If the product is not used as intended its protection and safety functions may
not work.
Installation
The unit is to be mounted on a DIN rail in a locked cabinet. Installation is
carried out by a qualied electrician. Cables must be fastened and secured so
that no risk for injury or re exists. Ventilation openings in the devise housing
may not be covered.
A circuit breaker shall be installed close to the unit and its power supply.
Function and position shall be clearly labelled. External voltage source
connected to DIGITAL OUT must be limited to a maximum of 0.5 A.
The equipment must be unplugged from the mains and other possibly
dangerous voltage sources during installation and service.
Quick start guide

www.abelko.se
Power supply
UltraBase30 is powered by 24 V DC, through the terminal marked +24V and
GND.
Requirements and characteristics of the unit’s inputs and outputs can be found
in the table below.
Port Supply
Supply expansion
module (port Ex)
+24V/GND 24 VDC* (>300 mA) 24 VDC, 1A
* Stabilized DC voltage.
The Power LED lights up when the device is energized and the Status LED
lights up when the device has started up and is working.
Safety instructions
All external equipment connected to the device must have double or
enhanced isolation (class II) from power mains or other dangerous
voltage source (>50 VAC or > 75 VDC).
Note that all cables used must be approved for at least 50 °C ambient
temperature.
At high ambient temperatures there is a risk for burning injuries. Wait
for the equipment to cool down, and use protective gloves.
Network connection
The unit is connected to a permanent network by the Ethernet port. The
factory default IP address is 10.0.48.94.
Local PC is used only to connect the unit directly to a PC. It has IP address
192.168.142.1, and can be used to congure the regular network connection
in the UltraBase30.
When you use the Local PC port, the computer should be congured for DHCP
(which it usually is).
1. Open a web browser and enter the IP address https://192.168.142.1 in
the address bar. This will take you to the login page.
User name and password the rst time you log in:
User name: cong
Password: ef56
2. Go to the menu Communication and Network, and set the IP
address and netmask, in order to congure the settings for the port
marked Ethernet.

www.abelko.se
You can also use DHCP, the unit will then automatically get network
settings. After a while, you can see which IP address it received. You
can use this IP address to access the device from a PC, connected to the
same network.
HTTPS
The rst time that you log in to an Ultra, you will be warned that the
connection is not private, secure, or similar. This is because the system uses
HTTPS for a secure and encrypted connection. The security is guaranteed by a
certicate that is issued for a specic address. Since the address is adjustable,
there is only a self-signed certicate for the unit.
You need to accept and add this exception. The procedure diers depending on
which browser you are currently using. The communication is still encrypted, so
no-one can see, for example, which passwords are being used.
Graphical programming
Graphical programming is available as an installable program. Download it at
www.abelko.se.
There is also a link to the program in your units user interface under
Conguration and Graphical programming.
Universal inputs
There are 16 universal inputs marked UI. Universal inputs can be used for both
resistive temperature sensors, voltage 0-10 V and current 0-20 mA. UI can also
be used as a digital status input for potential-freeswitches.
Resistive temperature sensors Voltage 0-10 V
Current 0-20 mA
Digital status input for potential-
free switches

www.abelko.se
Digital inputs
There are four digital inputs marked DI. Digital inputs can be used for digital
status, counters and for frequency measurement.
Analog outputs
There are six analog outputs for 0-10 V, marked AO. The gure below is an
example on how you can connect an AC-powered valve controller.
Digital outputs
There are four digital outputs marked DO. Digital outputs are open collector
that closes to ground (GND) when they are activated.
Cleaning
The housing is cleaned from dust and dirt using a dry cloth. Do not use
chemicals.
Recycling
UltraBase30 should be recycled as electronics.
Repair and service
Reparation and service shall always be performed by Abelko Innovation.
Contact your distributor rst if the need arises.
Manuals, updates and other information are available at
www.abelko.se.