ABI INTERIORS Aliro Accessible 14736 User manual

ALIRO ACCESS IBLE 140 ° CO NTINUOUS GRAB
RAIL
Dis cla imer: Pro du cts in th is man u a l mu s t b y la w b e in s ta lled b y licen s ed a n d reg is tered trad esp eo p le in acco rd a n ce w ith th e relevan t s ta n d a rd s . A BI a n d th e ma n u f a c tu rer/d is trib u to r
res erve t h e rig h t to v a ry s p ecifica tio n s o r d elete mo d els fro m t h eir ra n g e with o u t p rior n o tif ic a tio n . Dimen s io n s a re n o min a l mea s u remen t s on ly. Th e in f o rma tio n lis t ed is co rrec t a t th e time
o f p u b lica tio n , h o w ev er A B I a n d th e ma n u fa ctu rer/d is t ribu t o r takes n o res p o n s ib ilit y fo r p rin tin g errors . Co p yrig h t © A B I I n terio rs 2 02 2 P ty Ltd
SPECIFICATIONS
RECOMMENDED USE Domestic/Commercial
MATERIAL 316 Stainless Steel
MOUNTING HARDWARE INCLUDED Yes, M10 x 75mm Coach Screw
STANDARDS AS14 28 .1:2021

1
2
3
4
5
6
1
IN THE BOX
1
2
3
46
5
1
1
2
3
End Bracket x 2
610mm Rail x 1
140oBracket x1
140o Accessible Continuous
Grab Rail Kit (numbered components)
Fixing Kit
(unnumbered components)
Coach Screw x4
O Ring x 4
Fixing Bracket x4
Washer x 4
Grub Screw x 10
825mm Rail x1
Corner Bracket x1
1010mm Rail x1
4
5
6
ALTERNATIVE INSTALL FORMAT
Modularity of product permits installation on either the left or right hand walls.
1612
43
1061 551
760
1061
524
71
Structure
Structure
Structure
Note: Dimensions are nominal measurements only

INSTA LLATION G UIDE
3Mark out fixing points centre to centre, on a level floor,
ensuring grab rail placement meets AS1428.1:2021 standards.
Refer to alternative install location instructions for opposite wall
installation.
1061
71
1612
4Align fixing points with rail configuration, using a level, double
check fixing location. Drill pilot holes accordingly.
level
5Secure fixing brackets at previously marked fixing location.
Ensure fixing is level & fixed into appropriate structural support.
Drill
Coach Screw
Washer
Fixing Bracket
O ring
Pilot hole
6Slide grab rails onto brackets & fix with grub screw. Ensure
all fixings are tight and secure.
2Fix grab rails to brackets using allen key provided.
Note: do not tighten grub screws completely, this aids wall
mount install process.
1
1
2
3
4
5
6
1
For rough in, refer to Step 3 for wall structure set out.
Set out grab rail in numbered configuration as illustrated below.
(Numbered indication appears on previous page).
1061
551
Quick Tip: If sliding the
grab rail onto the brackets is
challenging, it may help to
remove this grub screw
during installation to allow
more movement. Be sure to
reinstall the grub screw!
Note: This product must be installed by a licensed tradesperson.
This product’s install must comply with AS1428.1:2021 for installation
within Australia. This is a general installation guide - there are many
factors that are involved that can alter the installation method. ABI takes
no responsibility if your product is not fixed to adequate wall structure.
524
43
Structure
Structure
Structure
760
DO NOT use crea m
cleaners or bleach.
These substances are
abrasive .
Regularly clean with
mildliquid deterg ent
or soapand water.
DO NOT use cleaning
pads with abrasive
surfaces as this may
scratch the materia l .
IMPORTANT
Loosen grub screws to
aid installation.
Tighten once installed.
Note: Dimensions are nominal measurements only
IMPORTANT
Place assembled grab rail
against wall to aid
wall marking/check
before drilling.