Able Planet BT400 User manual

LOCATION OF PARTS AND CONTROLS
1. Volume Up Button
2. Play/Pause Button
3. Volume Down Button
4. Multi-function Button/LED
5. Forward Button
6. Backward Button
7. Microphone
8. DC Charging Port
CHARGING HEADSET
1. Plug one end of the included USB cable into the DC Charging Port on the Headset.
2. Plug the other end into a USB port on your computer, or a USB AC adapter/5V 1A (not included)
and connect to an electrical outlet.
3. The LED will illuminate solid red while charging. The LED will shut off when fully
charged. The Headset takes approximately 3hours to charge from a completely
depleted battery.
4. You have approximately 8 hours of use from a fully charged battery, depending upon the
functions being used.
POWERING HEADSET ON AND OFF
1. Press the MULTI-FUNCTION BUTTON for 3 seconds. The LED will flash blue three times and you
will hear an ascending tone. The headset is now powered on.
2. Press the MULTI-FUNCTION BUTTON between three to five seconds. The LED will flash red three
times and you will hear a descending tone. The headset is now powered off.
1
2
3
7
4
5
6
LED STATUS CHART
POWER ON
POWER OFF
PAIRING
STANDBY MODE
AV ACTIVE MODE
HEADSET ACTIVE MODE
LOW BATTERY INDICATION
AUTO SHUTDOWN
CHARGING
COMPLETE CHARGING
LED flashes blue 3 times
LED flashes red 3 times
LED flashes between blue and red
LED is solid blue
LED flashes blue twice every 2 seconds
LED flashes blue once every 2 seconds
LED flashes red once 2 sec continuous
LED flashes red 3 times and powers off
(5 minutes with no Bluetooth® connection)
LED is solid red
LED is off
Foldable Bluetooth® Headset
BT400
14

PAIRING HEADSET WITH YOUR BLUETOOTH® DEVICE
You can pair the headset to any Bluetooth®-enabled device, like a cell phone, smartphone or a
Bluetooth®-enabled computer. You may also pair using a USB Bluetooth® dongle (not included) to
take calls to use with Skype or other meeting-type programs.
1. Press and hold the MULTI-FUNCTION BUTTON for six seconds to put the headset into pairing
mode. The LED will flash between blue and red and you will hear a double tone.
2. Set your Bluetooth® device to search for Bluetooth® headset
Note: See your Bluetooth® device’s manual for additional information on Bluetooth® pairing if you
need assistance.
3. Select the headset “BT400” from the list of found devices and connect the headset to your
Bluetooth® device. If prompted ,enter "0000" for the passkey.
4. The headset has successfully paired with your device when its LED begins to flash blue twice
every few seconds.
Note: After pairing for the first time, the headset will remember your Bluetooth® device so you
should only need to do this once. When the headset automatically reconnects (or asks if it can
reconnect), it will sound a single tone.
OPERATION
LISTENING TO MUSIC/AUDIO
When your headset is connected to a device with an A2DP profile, you can listen to stereo music
from a transmitter through your headset. You can connect a USB dongle, AV transmitter or
cellular phone with A2DP supported profile. Almost any A2DP source device supports AVRCP
that can use play/pause, next track and pre-track function.
Note: If you use AV transmitter with 3.5mm audio jack it won’t support the AVRCP function.
Working in AV connection mode, you can;
• Short press PLAY/PAUSE BUTTON to toggle between play and pause
• Short press the FORWARD or BACKWARD button to move forward or backward through your
audio tracks.
• Short press MULTI-FUNCTION BUTTON to initiate voice dial feature
• Use the VOLUME UP or VOLUME DOWN button to increase or decrease the volume level
of your audio through your headset
LISTENING TO MUSIC/AUDIO
Standby mode:
• Short press MULTI-FUNCTION BUTTON to initiate voice dial function
• Double click MULTI-FUNCTION BUTTON to initiate last number redial function
Incoming call mode:
• Short press MULTI-FUNCTION BUTTON/LED to accept a phone call
• Double click MULTI-FUNCTION BUTTON/LED when you hear a beep tone to reject call
While on a call mode:
• Short press VOLUME UP or VOLUME DOWN to adjust volume
• Double click MULTI-FUNCTION/LED BUTTON when beep tone sounds to toggle between calls
• Short press MULTI-FUNCTION/LED BUTTON to end call
• Short press PLAY/PAUSE BUTTON to mute the microphone
TROUBLESHOOTING
• If the Bluetooth® Headset does not work, try the following:
• Ensure your Bluetooth® device has charged
• Turn off all devices and then turn them on in the order instructed
• Ensure devices are within approximately 30 feet of each other
• Ensure the headset is connected by checking its LED status
Note 1: Some A2DP sources, like a 3.5mm interface transmitter, cannot support an AVRCP profile.
The remote control function will not work.
Note 2: Only cellular phones that support a hands-free profile can use voice dial, last number
redial, or the call transfer function.
32