AboLife M15 User manual

Model: M15
Customer Support:
Email:[email protected]

01
Our customer support team is providing video call guide service now,which will
guide you to complete the lock installation and setups in minutes. Feel free to
email us at [email protected] to schedule your video call.
Quick start tip:
Customer Support
Email:[email protected]

02
Prepare the door and check dimensions
backset
60 or 70 mm
54 mm
1"
25 mm
35 mm and 50mm
the door edge is 1" (25 mm).
If drilling a new door, use the supplied template and the complete door drilling instructions
Measure to confirm the thickness of the door is
between 1-3/8" and 2"(35mm and 50mm).
1-3/8" and 2"
1.
3.
2.
4.
Customer Support
Email:[email protected]

03
Install the latch and strike
1. Insert the latch bolt into the door.
2. Install strike on the door frame.
Twist the latch and adjust the bolt length.
(Make sure the latch bolt is retracted).
up YES up NO
Make sure t he
is in the bottom position.
T-shaped hole
No adjustment is required.
Proceed to next step.
Make sure the hole in the door
frame is drilled a minimum of
1"(25mm)deep.
YES
NO NO
up
2Customer Support
Email:[email protected]

Install the exterior assembly
3
NOYES
Route the cable through the door below
the bolt.and push the keypad onto the door.
The key must be pulled out when installing.
cable
Customer Support
Email:[email protected]

4
Install the interior assembly
2. Route cable through the
bottom of mouting plate.
1. Take off the mounting plate.
4. Ensure tight cable connection.
3. Tighten screws evenly.
5. Tighten screws evenly.
3
Loose the 2 screws
Note:
please support
exterior assembly
during mounting
plate installation.
Insert key and test latch.
if latch does not extend or retract smoothly.
please adjust mounting plate screws.
If the keypad and mounting plate are
deflection.
please loose mounting plate screws
and adjust.
NO NO
Cable
Mounting plate
The smooth side of
the plug should be at the bottom.
Customer Support
Email:[email protected]

Install the batteries and
perform the door handing process
06
5
Note:Do not use rechargeable batteries or Non-alkaline batteries.
Make sure the door is unlocked
and that you are using a fresh
set of batteries.
x3x2 Unsuccessfu l
Successful
1.Install 4 AA batteries in battery pack.
2. Perform the door handing process.
The batteries are not included.
If the latch bolt extends or retracts not smoothly.
please check the latch and re-install the lock.
1. Press ,the latch bolt extends by itself.
2. Enter preset code:123456,press , the latch
bolt retracts by itself.
GreenRed
Customer Support
Email:[email protected]

07
1 1
F a cto ry de fa u lt se ttin g s
:
:
:
:
6-10
SET
SET
1 1
F a cto ry de fa u lt se ttin g s
:
:
6-10
User ID 01
Setting button
Factory default settings
Customer Support
Email:[email protected]
Our customer support team is providing video call guide service now,which will
guide you to complete the lock installation and setups in minutes. Feel free to
email us at [email protected] toschedule your video call.
Quick start tip:

08
5I the keypad will be locked 90 seconds
90 seconds
Open the battery cover.
for more than 5 seconds
A factory reset will delete all codes associated with the lock.
Keep press holding set button more than 5 seconds until the lock short beeps
5times and light flash blue 5 times. then the beeps 1second and light flash
green 1 times. the lock has been reset sucessful.
exited
x5
blue
p
Customer Support
Email:[email protected]

0 9
1. For your safety, please change and remember your programming
code in time.
2
30
3programming
Remove the battevy cover,and Press the set button 1 time.
then the keypad will be light on. now the lock is in programming mode.
4
NEW RE-NEW
SET
SET
F a cto ry de fa u lt se ttin g s
:
:
6-10
F a cto ry de fa u lt se ttin g s
:
:
6-10
:
:
6-10
SET
User ID 01
Setting button
Factory default settings
Customer Support
Email:[email protected]

1 0
6-10
NEW ID
UC
1
NEW
ID UC
RE-NEW
UC
digits
Add new use code
SET
3
Delete All User codes
SET
2
ID
Delete User code
SET
Make sure you have more than 1 user code or else you can not delete it.
2 digits
2 digits Re
ID
Customer Support
Email:[email protected]

1 1
5-30
Sound On and Off
6
1 or 2
SET
Set Auto Lock:
5
Time
Cancel Auto Lock
5
0 0
SET
SET
5
.
.
Customer Support
Email:[email protected]

1 2
Alert Reason Solution
Door jammed while attempting
to lock.
Manually re-lock door. If needed,
reposition strike.
Unsuccessful programming. Attempt programming procedure
again.
Incorrect User Code ente red. Re-enter User Code.
button flashes red
3 times with 3 beeps.
button flashes red
3 times with 3 beeps.
5 incorrect User Codes entered
within one minute.
Re-enter User Code after 90
seconds keypad lock out.
LED redlight when press
any button.Low battery.
System Alerts
LED redlight when press
any button. and can not
unlock/lock.
LED green light and beeps
1 second after press
unlock/lock button.
the lock no respond.
Replace batteries.
Customer Support
The keypad and light
indicator no respond.
Battery run out.
Bad cable connection.
Use Micro-Usb supply power to
unlock or key to unlock then
replace batteries.
Re-connect the cable.
Super low battery.
Poor quality battery.
Our customer support team is providing video call guide service now,which will
guide you to complete the lock installation and setups in minutes. Feel free to
email us at [email protected] toschedule your video call.
Quick start tip:
Customer Support
Email:[email protected]

1 3
un
u n
Customer Support
Email:[email protected]

1 4
Customer Support
Email:[email protected]

1 5
B a cksid e ofTe m p la te
Back side of Template
Customer Support
Email:[email protected]