Abus Smartvest FUAA35000 User manual
Back to Contents 2 Back to Contents
English
Introduction
Dear Customer,
Thank you for purchasing this product.
ABUS Security Center hereby declares that this device and all components comply with RED
Directive 2014/53/EU. The devices also meet the requirements of the following EU Directives:
EMC Directive 2014/30/EU and RoHS Directive 2011/65/EU. The full text of the EU Declaration of
Conformity is available at the following Internet addresses:
www.abus.com/product/FUAA35010A
www.abus.com/product/FUHA35000B
www.abus.com/product/FUBE35001A
www.abus.com/product/FUHA35000C
www.abus.com/product/FUBE35011A
www.abus.com/product/FUHA35000D
www.abus.com/product/FUBE35020A
www.abus.com/product/FUMK35000A
www.abus.com/product/FUBW35000A
www.abus.com/product/FUSG35000A
www.abus.com/product/FUBW35010A
www.abus.com/product/FUSG35010A
www.abus.com/product/FUEM35000A
www.abus.com/product/FUWM35000A
www.abus.com/product/FUHA35000A
ABUS Security-Center GmbH & Co. KG
Linker Kreuthweg 5
86444 Affing
GERMANY
To ensure this condition is maintained and that safe operation is guaranteed, it is your obligation to
observe this user guide.
Please read the entire user guide carefully before putting the product into operation, and pay attention
to all operating instructions and safety information.
All company names and product descriptions are trademarks of the corresponding owner.
All rights reserved.
If you have any questions, please contact your specialist installation contractor or
specialist dealer.
Disclaimer
This user guide has been produced with the greatest of care. Should you discover any omissions or
inaccuracies, please contact us in writing at the address provided above.
ABUS Security-Center GmbH does not accept any liability for technical and typographical errors,
and reserves the right to make changes to the product and user guides at any time and without prior
warning.
ABUS Security-Center GmbH is not liable or responsible for direct or indirect damage resulting from
the equipment, performance and use of this product. No guarantee is made for the contents of this
document.
Back to Contents 3 Back to Contents
English
Explanation of symbols
The triangular high voltage symbol is used to warn of the risk of injury or health
hazards (e.g. caused by electric shock).
The triangular warning symbol indicates important notes in this user guide which
must be observed.
This symbol indicates special tips and notes on the operation of the unit.
Lists
1. …
2. …
Lists with a set order, given either in the text or warning notice.
•…
•…
Lists without a set order, given either in the text or warning notice.
Intended use
Only use the device for the purpose for which it was built and designed. Any other use is considered
unintended.
This device may only be used for the following purpose(s):
•The Smartvest wireless alarm system enables easy access to modern homes with its
combination of reliable all-round security and attractive home-automation functions. Up to
32 wireless components and four IP cameras can be connected to the Smartvest alarm panel
via the free app, enabling you to access the alarm control panel from anywhere in the world.
If an alarm is triggered, the alarm panel activates its built-in, high-volume 90 dB siren; it can
also raise the alarm simultaneously via push notifications in the app and email.
Important safety information
General
Before using this device for the first time, please read the following instructions carefully and observe
all warning information, even if you are familiar with the use of electronic devices.
All guarantee claims are invalid in the event of damage caused by non-compliance
with this user guide. We cannot be held liable for resulting damage.
We cannot be held liable for material or personal damage caused by improper
operation or non-compliance with the safety information. All guarantee claims are
void in such cases.
Retain this handbook for future reference.
If you sell or pass on the device to third parties, you must include these instructions with the device.
The following safety information and hazard notes are not only intended to protect your health, but also
to protect the device from damage. Please read the following points carefully:
Back to Contents 4 Back to Contents
English
Power supply
•Only operate this device using a power source which supplies the grid voltage specified on the
type plate. If you are unsure which voltage is supplied at the installation location, contact your
energy provider.
•Disconnect the device from the power supply before carrying out maintenance or installation work.
•To fully disconnect the device completely from the mains, the mains plug must be withdrawn from
the mains socket.
•In order to eliminate the risk of fire, the device’s mains plug should always be disconnected from
the mains socket, if the device is not being used for an extended period of time.
Overload/overvoltage
•Prior to unstable weather and/or when there is a risk of lightning strike, disconnect the device from
the mains network or connect the device to a UPS.
•Avoid overloading electrical sockets, extension cables and adapters, as this can result in fire or
electric shock.
Cables
•Always grasp all cables by the plug connector and do not pull the cable itself.
•Never grasp the power cable with wet hands, as this can cause a short circuit or electric shock.
•Do not place the device itself, items of furniture or other heavy objects on the cable and ensure
that it does not become kinked, especially at the connector plug and at the connection sockets.
•Never tie a knot in the cable and do not bundle it together with other cables.
•All cables should be laid so that they cannot be trodden on or cause a hazard.
•Damaged power cables can cause fire or electric shock. Check the power cable from time to time.
•Do not modify or manipulate the power cable or plug.
•Only use adapter plugs or extension cables that conform to applicable safety standards, and do
not interfere with the mains or power cables.
Children
•Keep electrical devices out of reach of children. Never allow children to use electrical devices
unsupervised. Children may not always properly identify possible hazards. Small parts may be
fatal if swallowed.
•Keep packaging film away from children. There is a risk of suffocation.
•This device is not intended for children. If used incorrectly, parts under spring tension may fly out
and cause injury to children (e.g. to eyes).
Back to Contents 5 Back to Contents
English
Installation location/operating environment
Place or mount the device on a steady, level surface and do not place any heavy objects on the device.
Make sure that there is adequate ventilation (do not place the Smartvest on a shelf, thick carpet, bed
or wherever the ventilation slits may be covered. Always leave a gap of at least 10 cm on all sides).
The Smartvest is not designed for operation in rooms prone to high temperatures or humidity
(e.g. bathrooms) or excessive dust accumulation.
For all components only suitable for indoor use, please ensure that
•no direct heat sources (e.g. radiators) have an effect on the components
•the components are not exposed to direct sunlight or strong artificial light
•no naked flames (e.g. lit candles) are placed on or next to the components
•contact with sprayed or dripping water is avoided
•the components (except the watersensor of the waterleak detector FUWM35000, follow the
installation instructions for the water sensor under 3.9) are not operated in the vicinity of water
and, in particular, never submerged (do not place objects containing fluids, e.g. vases or drinks
on or near the device)
•the components are not exposed to large temperature fluctuations, as otherwise there may be
condensation from humidity which may lead to electrical short circuits
For all components that are suitable for indoor and outdoor use, please ensure that
•the components are not exposed to excessive shock or vibration
•the components are not placed in the immediate vicinity of magnetic fields (e.g. loudspeakers)
•contact with aggressive liquids is avoided
•no foreign objects are able to penetrate the components
•the operating temperature and operating humidity of the components are observed.
Please refer to the relevant quick guide, technical information and installation instructions in Section 3
for information on proper installation and compliance with the operating environment for components.
Battery
All Smartvest components, with the exception of wireless sockets, are or can be supplied with a battery.
In order to guarantee a long lifespan and avoid fire and injury, please follow the instructions below:
•Do not dispose of the battery with household waste. Please dispose the batteries only via a return
system, for this, please inform yourself at the local disposal companies.
•The battery must not be directly exposed to heat or sunlight, and must not be stored in hot places.
•The battery must not be burned.
•The battery must not come into contact with water.
•The battery must not be dismantled, pierced or otherwise damaged.
•The battery contacts must not be short-circuited.
•The battery must be kept out of reach of small children.
•The battery cannot be recharged.
Back to Contents 6 Back to Contents
English
Unpacking the device
Handle the device with extreme care when unpacking it.
Packaging and packaging aids can be reused and, as far as possible, should be sent for recycling.
We recommend the following:
Paper, cardboard and corrugated cardboard as well as plastic packaging items should be placed in the
appropriate recycling containers.
If no such facility exists in the area, these materials should be put into the general household waste.
Warning
If the original packaging has been damaged, inspect the device. If the device shows signs
of damage, return it in the original packaging and inform the delivery service.
Start-up
Observe all safety and operating instructions before operating the device for the first time.
Warning
Improper or unprofessional work on the power supply system or domestic installations
puts both you and others at risk.
Connect the installations so that the mains power circuit and low-voltage circuit always run
separately from each other. They should not be connected at any point or become
connected as a result of a malfunction.
Care and maintenance
Maintenance is necessary if the device has been damaged (e.g. damage to the power cable and plug,
or the housing), or if liquids or foreign bodies have got into the interior of the device, or if it has been
exposed to rain or damp, or if it does not work properly or has been dropped.
Maintenance
•If smoke, unusual noises or smells develop, switch the device off immediately and unplug from
the socket. In such cases, the device should not be used until it has been inspected by a qualified
technician.
•Have all maintenance tasks carried out by qualified technicians only.
•Never open the housing on the device or accessories. If the housing is open, there is the risk of
fatal electric shock.
Cleaning
•Only clean the device housing with a damp cloth.
•Do not use products such as solvents, white spirit or thinners, or any of the following substances:
Brine, insect spray, solvents containing chlorine or acids (ammonium chloride), or scouring
powder.
•Rub the surface gently with a cotton cloth until it is completely dry.
The device operates with a dangerous voltage level. When conducting maintenance
work (e.g. cleaning), disconnect the device from the mains.
Back to Contents 7 Back to Contents
English
Contents
1. Device description.......................................................................................................................... 10
FUAA35000 Smartvest.......................................................................................................... 10
FUHA35000 Wireless Socket................................................................................................ 13
FUMK35000 Magnetic Contact ............................................................................................. 14
FUBW35000 PIR Motion Detector......................................................................................... 15
FURM35000 Smoke/Heat Detector....................................................................................... 15
FUSG35000 Siren ................................................................................................................. 16
FUBE35000/FUBE35001 Remote Key ................................................................................. 17
FUBE35010/FUBE35011 Control Panel ............................................................................... 18
FUWM35000 Flood Detector................................................................................................. 20
FUBE35020 Wireless Button............................................................................................. 21
FUSG35010 Wireless Door Bell........................................................................................ 22
FUEM35000 Vibration Detector......................................................................................... 23
2. Start-up........................................................................................................................................... 24
Installing the Smartvest App.................................................................................................. 24
Setting up the Smartvest ....................................................................................................... 24
Pairing components............................................................................................................... 27
Removing components.......................................................................................................... 29
General settings..................................................................................................................... 29
3. Installation ...................................................................................................................................... 31
FUAA35000 Smartvest.......................................................................................................... 31
FUHA35000 Wireless Socket................................................................................................ 32
FUMK35000 Magnetic Contact ............................................................................................. 32
FUBW35000 PIR Motion Detector......................................................................................... 34
FURM35000 Smoke/Heat Detector....................................................................................... 35
FUSG35000 Siren ................................................................................................................. 35
FUBE35000/FUBE35001 Remote Key ................................................................................. 36
FUBE35010/FUBE35011 Control Panel ............................................................................... 36
FUWM35000 Flood Detector................................................................................................. 38
3.10 FUBE35020 Wireless Button................................................................................................. 39
3.11 FUSG35010 Wireless Door Bell............................................................................................ 40
3.12 FUEM35000 Vibration Detector............................................................................................. 40
4. Operation........................................................................................................................................ 42
Navigation bar and footer ...................................................................................................... 43
Overview................................................................................................................................ 44
Hotkeys.................................................................................................................................. 46
Rooms ................................................................................................................................... 47
Cameras................................................................................................................................ 48
Contacts................................................................................................................................. 50
Events.................................................................................................................................... 51
Alarm view............................................................................................................................. 53
Back to Contents 8 Back to Contents
English
5. Configuration.................................................................................................................................. 54
Configuration overview.......................................................................................................... 55
Components .......................................................................................................................... 56
5.2.1 Pairing the camera................................................................................................................ 56
5.2.2 Pairing the wireless socket.................................................................................................... 56
5.2.3 Pairing the magnetic contact................................................................................................. 57
5.2.4 Pairing the motion detector ................................................................................................... 57
5.2.5 Pairing the smoke/heat detector ........................................................................................... 57
5.2.6 Pairing the siren .................................................................................................................... 58
5.2.7 Pairing the Remote Key ........................................................................................................ 58
5.2.8 Pairing the control panel ....................................................................................................... 58
5.2.9 Pairing the Flood Detector .................................................................................................... 59
5.2.10 Pairing the Wireless Button................................................................................................. 59
5.2.11 Pairing the Wireless Door Bell ............................................................................................ 59
5.2.12 Pairing the Vibration Detector ............................................................................................. 60
Configure components .......................................................................................................... 60
5.3.1 Setting up the alarm panel .................................................................................................... 60
5.3.2 Setting up the wireless socket............................................................................................... 61
5.3.3 Setting up the magnetic contact............................................................................................ 61
5.3.4 Setting up the motion detector .............................................................................................. 61
5.3.5 Setting up the smoke/heat detector ...................................................................................... 62
5.3.6 Setting up the siren ............................................................................................................... 62
5.3.7 Setting up the Remote Key ................................................................................................... 63
5.3.8 Setting up the control panel .................................................................................................. 63
5.3.9 Setting up the Flood Detector ............................................................................................... 64
5.3.10 Setting up the Wireless Button............................................................................................ 65
5.3.11 Setting up the Wireless Door Bell ....................................................................................... 65
5.3.12 Setting up the Vibration Detector ........................................................................................ 66
5.3.13 Setting up the camera......................................................................................................... 67
Hotkeys.................................................................................................................................. 69
Scenarios............................................................................................................................... 70
5.5.1 Application examples –Basics.............................................................................................. 70
5.5.2 Open/closed magnetic contact scenario............................................................................... 71
5.5.3 Sunrise/sunset scenario........................................................................................................ 71
5.5.4 Door bell alarm panel scenario ............................................................................................. 72
5.5.5 Wireless Button scenario ...................................................................................................... 72
5.5.6 Wireless Door Bell scenario.................................................................................................. 72
Schedules.............................................................................................................................. 73
Advanced settings ................................................................................................................. 74
5.7.1 Network settings.................................................................................................................... 74
5.7.2 Security settings.................................................................................................................... 74
5.7.3 Status configuration............................................................................................................... 75
5.7.4 Notifications........................................................................................................................... 77
Back to Contents 9 Back to Contents
English
5.7.5 Firmware update ................................................................................................................... 78
5.7.6 Adopt time............................................................................................................................. 79
5.7.7 Daylight saving time.............................................................................................................. 79
5.7.8 About..................................................................................................................................... 79
5.7.9 Additional modes................................................................................................................... 79
6. Technical data................................................................................................................................ 80
7. FURM35000A Smartvest Wireless Smoke/Heat Detector............................................................. 86
Introduction............................................................................................................................ 86
Safety information.................................................................................................................. 87
Scope of delivery................................................................................................................... 88
Technical data ....................................................................................................................... 88
Functional principle and features........................................................................................... 88
Behaviour in case of alarm.................................................................................................... 89
Selecting location................................................................................................................... 89
Installation and start-up ......................................................................................................... 90
Displays and functions........................................................................................................... 90
Care and maintenance ...................................................................................................... 93
Warranty ............................................................................................................................ 94
Disposal............................................................................................................................. 94
Declaration of conformity................................................................................................... 94
Declaration of performance ............................................................................................... 95
Back to Contents 10 Back to Contents
English
1. Device description
This section contains descriptions of the Smartvest and all associated components.
FUAA35000 Smartvest
Front
1
Power LED
Green
On
System is supplied with power
Off
No power supply
2
Status LED
Off
System is “disarmed”
Yellow
On
The system is “disarmed” and there is a fault
(e.g. battery dead or magnetic contact is “open”)
Blue
On
System is “armed”
Red
On
System is “armed” and in the alarm state
(normal alarm, tamper alarm or panic alarm)
3
Network LED
Green
On
Connection to network and internet
Off
Connection to network without internet
Red
Flashing
No network connection
4
Optional stand. Removable for wall installation.
1
4
2
3
Back to Contents 11 Back to Contents
English
Under side
1
Reset button
To reset passwords to the default settings (123456) and network settings
to DHCP:
•While the system is in operation, press and hold the reset button for
>10 seconds using a paper clip. The power LED will go out and a
continuous tone will sound. The system then restarts.
Resetting the system to the default settings means that all settings are reset
and component pairings are deleted.
•Press the reset button with the alarm control panel turned off, and
hold it for >10 seconds while turning on the alarm control panel.
The power LED will go out and a continuous tone will sound. The
system then restarts.
2
RJ45 connection
Integrated network access 10/100 Mbit
3
Power supply
5 V DC/1.5 A. Device starts automatically when powered by line voltage.
4
Hygrometer
Integrated hygrometer for measuring temperature and humidity
1
4
2
3
Back to Contents 12 Back to Contents
English
Rear
1
Battery
operation
6 x AA (1.5 V) batteries for backup power supply (approx. 5h battery life)
Changing the battery
Push the clips to open the battery compartment cover.
Remove the six dead AA (1.5 V) batteries from the compartment and replace
with six new AA (1.5 V) batteries. Make sure they are facing in the direction
shown on the compartment floor, then close the battery compartment by
replacing the cover.
2
Mounting
bracket
Mounting bracket for wall installation
Drill hole spacing: 10 cm (drilling template provided)
3
Loudspeaker
Smartvest loudspeaker with a maximum volume of 90db.
4
Background
LEDs
Off
Off
System is “disarmed”
Yellow
On
The system is “disarmed” and there is a fault
(e.g. battery dead or magnetic contact is “open”)
Blue
On
System is “armed”
Red
On
System is “armed” and in the alarm state
(e.g. magnetic contact open).
5
Cabling
Cabling for power supply and network cable.
1
4
2
3
5
Back to Contents 13 Back to Contents
English
FUHA35000 Wireless Socket
1
Schuko socket
Schuko socket type F (CEE 7/4). Can be used in the following countries:
Germany, Austria, Sweden, Netherlands
2
Status LED
Off
Wireless socket is activated; power is being
transmitted.
Blue
On
Wireless socket is ready and activated; power is
not being transmitted to the appliance.
Flashing
Wireless socket is starting up
Orange
Flashing
Repeater mode started
On
Wireless socket is ready and activated; power is
not being transmitted to the appliance.
Repeater modeon and connectedwithacomponent.
3
Button
Press this button once to activate or deactivate the wireless socket.
Press and hold the button for five seconds, to activate repeater mode.
4
Schuko plug
Schuko plug type F (CEE 7/4). Can be used in the following countries:
Germany, Austria, Sweden, Netherlands
Repeater mode
As well as switching appliances, the wireless socket can also be used as a wireless repeater for another
component. To do this, take the following steps:
1. Press and hold the button for five seconds to activate repeater mode. The status LED will start to
flash orange.
2. For any components that you want to connect to the wireless socket, carry out the manual process
for pairing components (see Section 5, Configuration).
3. The status LED lights up orange when the connection is successful
4. To deactivate repeater mode again, first disconnect the switch. Press and hold the button.
Reconnect the switch. Wait until the LED flashes blue and only then release the button.
If deactivation was successful, the LED will now light up blue.
Note
It is only ever possible to connect one component to a wireless socket.
Further information on the wireless socket
Programming
Removal
Installation
Configuration
Technical data
1
2
3
4
Back to Contents 14 Back to Contents
English
FUMK35000 Magnetic Contact
1
Transmitter
component
Contains a wireless component
Mounted on window frame
2
Signal LED
Blue
Flashing
Magnetic contact is closed
Magnetic contact is opened
3
Battery
operation
1x 3 V button battery (CR2032) for power supply (up to one year battery life).
The Smartvest App warns you when the battery is low. Follow the instructions
in the app.
Changing the battery
Slide the battery compartment cover out in a downwards direction.
Remove the dead 3 V button batteries from the holder provided and replace
with a new 3 V battery, then close the battery compartment by replacing
the cover.
4
Magnet
component
Contains a magnet component
Mounted on window or door
Further information on the magnetic contact
Programming
Removal
Installation
Configuration
Technical data
1
2
3
4
Back to Contents 15 Back to Contents
English
FUBW35000 PIR Motion Detector
1
Catch
Catch for removing the rear panel
2
Pair button
Button for manual pairing with the Smartvest
Activate test mode: press for 5 s
Deactivate test mode: press for 5 s
3
Tampering
contact
Tampering contact for alarming in the event of unwanted removal
4
Battery
operation
3 x AA (1.5 V) batteries for power supply (up to two years battery life)
The Smartvest App warns you when the battery is low. Follow the instructions
in the app.
Changing the battery
Press the catch on the underside of the PIR Motion Detector and remove the
rear panel. Remove the 3 dead AA (1.5 V) batteries from the compartment
and replace with 3 new AA (1.5 V) batteries. Make sure they are facing in the
direction shown on the compartment floor, Reattach the PIR Motion Detector
to the mounted rear panel.
Note
In test mode, the PIR Motion Detector’s energy-saving mode is deactivated so it triggers
each time motion is detected. Use this to check whether the detector fully covers the
monitored space. Deactivate test mode after use, as otherwise this will severely affect the
battery life.
Further information on the motion detector
Programming
Removal
Installation
Configuration
Technical data
FURM35000 Smoke/Heat Detector
Refer to the instructions for the smoke/heat detector.
(See Section 7 FURM35000 Smartvest wireless smoke/heat detector)
1
2
3
4
Back to Contents 16 Back to Contents
English
FUSG35000 Siren
1
LED chamber
LED flashes (according to setting) in the event of an alarm and to
acknowledge changes to the siren settings. If the system status changes, the
siren will flash two times.
2
Loudspeaker
Siren loudspeaker with an adjustable volume of 80 db or 100 db.
3
Pair button
Button for manual pairing with the Smartvest
4
Tampering
contact
Tampering contact for alarming in the event of unwanted removal
5
Battery
operation
4 x C (1.5 V) batteries for power supply (up to two years battery life)
Changing the battery
Put the system in the maintenance mode before you remove the siren from
the bracket.
Loosen both screws on the cover. You do not need to completely remove the
screws. Lift the cover upwards from the bottom and remove.
In order to access the screws more easily when changing the batteries,
you can temporarily remove the tampering contact’s rubber cover.
Remove the dead 4 C (1.5 V) batteries from the compartment and replace
with the new 4 C (1.5 V) batteries. Make sure that the battery is always
positioned with the negative end against the spring. Place the top end of the
cover into the holes provided and attach the cover beneath using the two
screws.
Further information on the siren
Programming
Removal
Installation
Configuration
Technical data
1
2
3
4
5
Back to Contents 17 Back to Contents
English
FUBE35000/FUBE35001 Remote Key
1
Signal LED
Blue
Flashing
Acknowledges when button is pressed
2
Arm button
Button for arming the Smartvest
Press and hold for five seconds to part set
3
Disarm button
Button for disarming the Smartvest
4
Camera button
Button to start recording for connected cameras
5
Panic button
Button for triggering the panic alarm (press for 3 seconds)
6
Battery
operation
1x 3 V button battery (CR2032) for power supply (up to two years battery life)
The Smartvest App warns you when the battery is low. Follow the instructions
in the app.
Changing the battery
Remove the battery compartment on the side of the Remote Key.
Remove the dead 3 V button batteries from the holder provided and replace
with a new 3 V battery, Push the battery compartment back into the Remote
Key.
Note
The exact reaction caused when a button is pressed depends on the app settings. Refer
to Section 5.7, Advanced settings for the arm and disarm buttons, and Section 5.4,
Hotkeys for the camera button and panic button.
Further information on the Remote Key
Programming
Removal
Installation
Configuration
Technical data
1
2
3
4
5
6
Back to Contents 18 Back to Contents
English
FUBE35010/FUBE35011 Control Panel
1
Arm button
Button for arming the Smartvest
2
Disarm button
Button for disarming the Smartvest Verification is required after pressing (PIN
or RFID Chip).
3
Part
set button
Button for part setting the Smartvest.
4
Panic button
Button for triggering the panic alarm (press and hold for five seconds).
5
Settings button
Button for settings options. Verification is required after pressing (PIN code).
6
RFID reader
Signal LED
Blue
Flashing
RFID reader has now been active for 30 seconds
and is awaiting verification.
7
Mount
slot
These square slots are for fixing the control panel to the mount.
8
Battery
operation
4 x AA (1.5 V) batteries for power supply (up to one year battery life)
The Smartvest App warns you when the battery is low. Follow the instructions
in the app.
Changing the battery
Once you have set the alarm panel to maintenance mode, remove the
control panel from the mount by lightly pressing the tab at the bottom of the
mount downwards. You can now slide the control panel out from above.
Loosen the screws on the back and open the battery compartment.
Remove the four dead AA (1.5 V) batteries from the compartment and
replace with four new AA (1.5 V) batteries. Make sure the polarity is correct
when replacing the batteries.
9
Reset button
Resets the control panel to the default settings, i.e. all settings are reset, and
the PIN code and all paired RFID chips are unpaired.
•Press and hold the control panel’s reset button for > 5 seconds during
operation. Two consecutive signal tones will sound to confirm reset.
The control panel will then restart.
•The default PIN code is (1234), no RFID chips are paired. Please
ensure that the control panel is still paired in your Smartvest system.
1
2
3
4
5
6
7
8
9
10
11
12
Back to Contents 19 Back to Contents
English
10
Tampering
contact
Tampering contact for alarming in the event of unwanted removal
11
Cabling
Cabling for the power supply
12
Sounder
Control panel sounder
Note
The exact reaction caused when a button is pressed depends on the app settings. Refer
to Section 5.7, Advanced settings for the arm and disarm buttons, and Section 5.4,
Hotkeys for the panic button.
Note
An exit delay of 30 seconds is preset on the control panel. When pressing the arm/part
set button, the Smartvest will only be armed/part set once this time has elapsed.
You can increase the exit delay to a total of 60 seconds by adjusting the exit delay for
arm/part set under Status configuration in the app’s advanced settings (see Section 5.7).
–Please note that, in this case, the exit delay will remain set to 30 seconds for arming/part
setting via app and Remote Key.
The exit delay set on the control panel can be cancelled by pressing the disarm button.
Operation
Arming the system
Press the button to arm the system. Once the button has been pressed, an exit delay begins which
arms the system after 30 seconds. A signal tone sequence with decreasing intervals (crescendo)
indicates that arming is imminent.
Part setting the system
Press the button to part set the system. Once the button has been pressed, an exit delay begins
which part sets the system after 30 seconds. A signal tone sequence with decreasing intervals
(crescendo) indicates that arming is imminent.
Disarming the system
Press the button to disarm the system. Once the button has been pressed, you have 30 seconds for
verification using a four-digit PIN code or RFID chip (see Section 5.2). Please hold the RFID chip in front
of the blue flashing LED. Successful verification is indicated by two consecutive signal tones.
Triggering a panic alarm
To trigger a panic alarm, press and hold the button for > five seconds.
Further information on the control panel
Programming
Removal
Installation
Configuration
Technical data
Back to Contents 20 Back to Contents
English
FUWM35000 Flood Detector
1
Mount
slot
These slots are for fixing the Flood Detector to the wall.
2
Battery
operation
4 x AA (1.5 V) batteries for power supply (up to two years battery life)
The Smartvest App warns you when the battery is low. Follow the instructions
in the app.
Changing the battery
Once you have set the alarm panel to maintenance mode, remove the flood
detector panel from the wall by sliding it out from above. Open the battery
compartment, remove the 4 dead AA (1.5 V) batteries from the compartment
and replace with 4 new AA (1.5 V) batteries. Make sure the polarity is correct
when replacing the batteries (+/-).
3
Mute button
In the event of an alarm, you can use this button to disarm the sounder for
the flood detector.
4
Pair button
and Test button
Button for manual pairing with the Smartvest.
5
Sensor socket
The sensor can be connected using this socket
6
Sounder
The flood detector sounder sounds for five minutes in the event of an alarm
Operation
Muting the sounder
The flood detector sounder sounds for five minutes in the event of an alarm. The sounder can be
muted using the mute button. The sounder is then reactivated if the water sensor is triggered again.
Function test:
Press and hold the Pair/Test button for five seconds to activate test mode (three beeps will sound to
confirm). The detector is now in test mode for three minutes, which means the flood detector sirens
sound for two seconds every time the sensor is triggered, although no alarm is sent to the Smartvest
alarm panel.
Further information on the Flood Detector
Programming
Removal
Installation
Configuration
Technical data
3
5
1
2
4
Table of contents
Other Abus Receiver manuals
