AccessPRO MAG-175 User manual

MAG-175
ELECTROMAGNETIC LOCK (FORAUTOMATIC DOOR)
MANUAL

1
1. Featuresintroductions
 All-in-one design far easy installation. The lock itself would not haveany residual
magnetism.
 Adjustable width (59mm-89mm) far useof different sliding doors' slots.
 Armature bracket which can beadjusted horizontally or vertically for betterfitting.
 Voltage inputdesigntofitallsliding doors (DC12V).
 The lock itself is equipped with release switch and indicator for better maintenance of
the sliding doors.
 Built-in photocoupler connects with egress delay circuit push button point.
Maximum holding force of 80kg/ 175 lbs.
 Currents: 150mA{dependingonDC12Vtesting).
Dimensions:
 Magnetic lockbody:118 mm (L)x 66mm (W) x 53.5mm (H).
 Armature: 63mm (L) x38mm (W)x 126.5mm (H).
 Totalweight:1.25kg.
2. Modelseries
 5PIN connector without lockstatus point.
 7PIN connector with lockstatus point.
3. Panel
3PIN connector: To set either 110V or 220 V
5 PIN connector: DC12, external push button,
triggers to open door.
7 PIN connector: DC12 V, external push
button, triggers to pen door, lock status point.
Release switch: For better maintenance of
sliding door.
Indicator (red):
Normal state: Blinking
Door opening: Light on

2
4. lnstallation instructions
.
P.S. (1)Please selectonly one power input (DC12V or 110Vor220V)
(2)Triggertodooropen relaycontact rating: 1A@30VDC,0.5A@120VAC.

3
5. Connector Wiring
A .Use of DC12V only

4
6. Precautions
(1) Before installation, please check the voltage and polarity of the power supply in
order to avoid wrong connection causingdamage tothe magnetic lock.
(2) Please make sure the armature isfit correctly toavoid any damage to the door
before use.
(3) Please do not attempt to repair or conduct any modificationtothe system,
unless by qualifiedpersonnel.
{4) Warranty period for the magnetic lock is 1year.
7. lnstallations
(1) Dimensions

5
(2) Physical installation
(3) Template assembly
Adjustable brackets (Top)
Fixedscrews
Adjustable brackets (Bottom)
Adjustablescrews (A)
•The use of the template is tofix the lock body to the adjustable bracket.
8 adjustable screws adjust the lock body on thetemplate's two longvertical slits.
•8 adjustable screws There are 2 adjustable screws for all 4 sides ofthe template for
stronger position holding andto avoidany damage tothe template.
•A bendingareaoftheadjustable bracketisbeingputintotheslot.
Usefixed screws to fit the lock body tightly to the slot.

6
(4) Adjustingthe brackets
Adjustablescrews (B)
Adjustable brackets (Top)
Adjustablescrews (A)
Adjustable brackets (Bottom)
A. Loosenall 8adjustable screws (Aand B).Adjust the bracket (bottom) tothe lowest
pointandtighten all 4 adjustable screws (A).
B. Fitthe lock bodyto theslot.Adjust the bracket (top)to the slot.
C. Finally,tighten all 4 adjustable screws (B) andallfixed screws.
(5) Adjustingthearmature
Loosen the fixed screws and move
the armature tothe different
direction to suit different door.
Adjusting the armature
horizontally
.
.
.
..
.
Adjustingthe armature
vertically.

7
Relevant positions: