Accusplit Exclusive AX602 User manual

ACCUSPLIT, Inc.
7901StoneridgeDrive,Suite350
Pleasanton,CA94588USA
800-965-2008925-290-1900FAX925-290-1930
www.ACCUSPLIT.com•[e-mail]
167-1512

ACCUSPLIT®
exclusive
AX602
STOPWATCH
OPERATING
INSTRUCTIONS

ACCUSPLIT® AX602
DIGITAL 100 MEMORY STOPWATCH
WITH SPLIT AND LAP TIME MEASUREMENT AND
STROKE/FREQUENCY MEASURING FUNCTIONS
FEATURES
The Quartz Stopwatch is a digital
stopwatch featuring memory and
stroke/frequency measuring func-
tions. In addition, the stopwatch
is water resistant. Therefore, it is
suitable for aquatic sports or use
in rainy weather.
• STOPWATCH
The stopwatch can measure up
to 10 hours in 1/100 seconds.
• SPLITTIME/LAPTIME
 MEASUREMENT
Up to 100 split times and lap
times can be measured.
2

• LARGE-SIZEDTHREE-ROWDISPLAYPANEL
Total elapsed time, split time and lap time are displayed at the same
time in separate rows, and they can be measured successively
without releasing split or lap time measurement.
• MEMORYFUNCTION
Up to 100 measurements can be stored in memory, and they can be
recalled after the measurement is over.
• TIME/CALENDARDISPLAY
Year, month, date, hour, minutes, and seconds can be displayed while
the stopwatch is not in use.
• BATTERY
Lithium battery CR2032 or equivalent is used.
• ACCUSPLIT“X”CASE
Exclusive professional case with no-fail buttons.
3

There are four buttons as
indicated in the illustration.
STROKE/FREQUENCY MEASURING MODE
STROKE/FREQUENCY MEASURING MODE
TIME/CALENDAR
display
STOPWATCH
display
4
STROKE/FREQUENCY MEASURING MODE
STROKE/FREQUENCY
MEASURINGdisplay
A
C
B
D

5
TIME/CALENDAR SETTING
1. Press “D” to show the time/calendar display. The time/calendar display
mark will appear.
2. S1 – Press and hold “B” for 2 seconds until seconds display begins flashing.
TIME/CALENDARdisplay mark
A
C
B
D
Year
Month and date
Seconds
Minutes
Hour
ACCUSPLIT products use a common setting procedure known as S1-S2-S3-S4.
S1 (2 sec) - Enter set function OR
S1 (4 sec) - Enter set function &
clear the current settings
S2 – Select field to be set
(selected field will flash)
S3 – Set field to desired settings
S4 – Exit setting function

6
3. S2 – Press “B” repeatedly to select the digits (flashing) to be adjusted.
With each press of “B,” the digits to be adjusted change over in the
following order.
4. S3 – Press “A” to set the flashing digits or reset the seconds to “00”.
 • Thedigitsmovequicklyif“A”iskeptpressed.
 • Whenthesecondsdigitscountanynumberfrom”30”to“59”and“A”is
pressed, one minute is added and the second digits are reset to “00”.
5.S4– After all the adjustments are completed, press “A” repeatedly until watch
exits set mode and returns to the TIME/CALENDAR display.
Notes:
1. Hour digits are displayed in the 24-hour indication.
2.Yeardigitscanbesetfrom1988to2027.Thecalendaradjustsautomaticallyfor
odd and even months including February of leap years.
 seconds minutes hour year month date
Note: The watch exits set mode automatically after setting date.

7
STOPWATCH
Press “D” in the TIME/CALENDAR display to show the STOPWATCH display.
The STOPWATCH display mark will appear.
The STOPWATCH can measure up to 10 hours in hours, minutes, seconds and
1/100 seconds.
 • Beforeusingthestopwatchbesuretoresetthedigitsto“0:00:00.00”.
When the stopwatch is stopped, press ”B” to reset.
When the stopwatch is counting, press “A” to stop the measurement
and then press “B”.
A
C
B
D
STOPWATCHdisplay mark
Split time
Lap time
Total time (accumulated
elapsed time)
Split/lap number

A A B
 • “Splittime”referstoanelapsedtimerequiredtocoveradistancefrom
the start to a given point.
 • “Laptime”referstoanelapsedtimerequiredtocoveragivensection
of the whole distance.
Lap time
Split time
Start
1.STANDARDMEASUREMENT
Hour Seconds
Minutes 1/100 seconds
START STOP RESET
8

2.ACCUMULATEDELAPSEDTIMEMEASUREMENT
9
START STOP RESTART
RESET STOP
Restart and stop
of the stopwatch
can be repeated
by pressing “A”.
BA
A A