Acekare Yomper User manual

1/ 17
Make your life easier !
Yomper
Removable electric motorization for wheelchair
Set up guide
for the frame
on foldable wheelchair
with braces
v1.3 - 23/02/2017

2/ 17

3/ 17
Table of contents
1Presentation of the frame .................................................................................. 4
2Setting up the frame......................................................................................... 6
2.1 Step 1 : Open the frame and lock it in the clip (B) .......................................... 6
2.2 Step 2 : Protect the frame of the wheelchair with the tape supplied .................. 6
2.3 Step 3 : Measure the distance from the ground to the axis of the frame’s tube .. 7
2.4 Step 4 : Setting up the right loop (A') ............................................................ 7
2.4.1 Unscrew the indexing digit (L) ............................................................... 8
2.4.2 Unscrewing the 2 screws (2) and setting up the right loop on the right side
of the frame..................................................................................................... 9
2.4.3 Put back the indexing digit .................................................................... 9
2.5 Step 5 : In the same way, set up the left loop .............................................. 11
2.6 Step 6 : Close the frame and measure the distance L .................................... 11
2.7 Step 7 : Check the height between the frame’s axis and the ground ............... 13
2.8 Step 8 : Check the space for the insertion of the Yomper ............................... 13
2.9 Step 9 : Check the adjustment of the stop (H).............................................. 14

4/ 17
1 Presentation of the frame
The fixing frame of the Yomper is already assembled when it’s delivered. It is to be set
up on foldable wheelchairs equipped with braces :
It is composed of the following parts :
•2 loops (A et A')
•1 clip (B)
•1 pivot (C)
•1 bar –left part (D)
•1 bar –central part (E)
•1 bar –right part (F)
•2 locknuts (G et G')
•1 stop (H)
•1 bar frame (I)
•1 clip frame (J)
•1 torque spring (K)
•1 indexing digit(L)

5/ 17
The 2 loops (A et A’) will be fixed on the frame of the wheelchair.
All the screws and bolts necessary to set up the frame are already in place :
•2 round head screws M6 x 50 (1)
•3 round head screws M6 x 40 (2)
•2 countersunk screws M3 x 10(3)
•2 white nylon washers (4)
•2 black nylon washers (5)
•2 x 2 washers M6 (6)
•1 Nylstop screw M6 (7)
•2 Nylstop screws M3 (8)

6/ 17
2 Setting up the frame
2.1 Step 1 : Open the frame and lock it in the clip (B)
2.2 Step 2 : Protect the frame of the wheelchair with the tape supplied
Protect the frame at a distance of 110mm from the wheels’ axis :

7/ 17
2.3 Step 3 : Measure the distance from the ground to the axis of the
frame’s tube
The measurement must be made at the level of the protection that you set up during
step 2 :
2.4 Step 4 : Setting up the right loop (A')

8/ 17
Check out the chart below to know in which holes you must put the screws.
h
Screws in the
holes
210 à 220mm
1 et 1'
220 à 230mm
2 et 2'
230 à 240mm
3 et 3'
240 à 250mm
4 et 4'
2.4.1 Unscrew the indexing digit (L)
Before screwing the loop on the right, you need to unscrew the indexing digit (L) to
reach the screw on top (1).

9/ 17
2.4.2 Unscrewing the 2 screws (2) and setting up the right loop on the right side of the frame
The loop must come at the level of the space protected with tape :
Put back into place the 2 washers M6 (6) on the lower screw,
between the 2 parts of the loop
2.4.3 Put back the indexing digit

10 / 17