Acnodes APH8185 User manual

All rights reserved. Product description and product specifications aresubject to changewithout notice.
For lastest product information, please v isit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA 91710 Tel: [phone] Fax: [phone]
© C opyright 2017Acnodes C orp.

The OSD Control
Control Key Definition
1. Power LED Indicator: Green Light is with the signal; Red Light is out of signal or extraordinary.
2. Sleeping Mode Indicator: Red light indicator when the monitor going to sleep
3. 「On/Off」: Press the button to turn on/off the display.
4. 「Menu/Select」: 1. Call the Menu 2. Confirm the selection
5. 「Auto/Exit」: 1. Adjust the display to the best position. 2. Exit the options
6.「+」:Press the button to adjust the increasing value of selected OSD control option.
7.「-」: Press the button to adjust the decreasing value of selected OSD control option.
Quick Selecting Menu
1.「+ 」：Press this key can quickly go to signal input selection menu, (if the monitor has more
than one input source), there are “Auto/VGA/DVI” three modes. Default is in “Auto” state.
Then press “OK (Menu)” key to confirm the selection.
2.「Auto/Exit」: Press this key can adjust the display to the best position and resolution.
OSD Menu Operation
Press「MENU」and the screen will appear the following OSD icons:
1.Power LED
2.Sleeping Mode
LED
3.
4.
5.
6.
7.

OSD Menu Adjustments:
Press「+」,「-」to increase or decrease the light bar for moving to the right icon you
want to adjust.
Press 「MENU/ENTER」again to confirm in the selected item.
Then, the selected bar will become yellow at bottom under the item.
Press 「+」or「-」to select the item and press「MENU/ENTER」again, the value will
turn red, press「+」or「-」to increase or decrease the value.
When it is finished, press「MENU/ENTER」to exit; the red value will turn back to yellow.
Then you can continue to next adjustment.
Color Luminance Adjustment
Contrast: Adjust the contrast level of brightness and darkness of the screen.
Brightness: Adjust the brightness of the screen.
Backlight
：
Th
e backlight has default set in the most bright.
Normally the function has no effect.
BRIGHTNESS
：
Adjust the brightness of the screen.
CONTRAST
：
Adjust the contrast level of brightness and darkness of the
screen.
SHARPNESS:
Adjust
the sharpness of display

Display
Image H./V. Position
Contrast: Adjust the contrast level of brightness and darkness of the screen.
Brightness: Adjust the brightness of the screen.
AUTO
ADJUSTMENT
:
Auto
adjusting the display position and its best phase and clock
settings.
H
. POSITION：
Adjust the size of horizontal image (left and right sides).
V
. POSITION：
Adjust the size of vertical image (
up and down sides).
PIXEL
CLOCK：
This is normally
set by different clocks, factory default has been setup
PHASE
：
Adjust the image distortion appearing as horizontal “noise” on the
screen.

OSD
OSD POSITION
：
Display the location of OSD Menu.
OSD TIME OUT
：
Reset
：
LANGUAGE
：
Display time duration of OSD Menu.
Recall Setting Value Yes/No.
Select Languages
Remark2
Remark 2: Language Selection
English
Français：French
Deutsch：German
Español：Spanish
日本語：Japanese
繁體中文：Traditional Chinese
簡體中文：Simplified Chinese
COLOR Temp
9300
K：
Asian
Area.
7500
K：
Asian
Area.
6500
K：
Europe
and North American Area.
SRGB
：
Europe
and North American Area.
USER
COLOR：
RED
：
GREEN
：
BLUE
：
User’s
setting.
Red adjustment. User’s setting
Remark 1
Green
adjustment. User’s setting Remark1
Blue
adjustment. User’s setting Remark1
Remark 1.: When moving the light bar to the selected item, press ENTER (MENU/ENTER), the bar and value will
become yellow (or red), then press「+」or「-」to adjust the value.

Others
Reset: Recall settings to the factory default setting
Menu Time: OSD Menu showing period during no any instructions given.
OSD H. Position：Present the position of the OSD horizontal position
OSD V. Position：Present the position of the OSD vertical position
Language: English / French / German / Japanese/ 繁體中文 / 簡體中文
Transparency: Adjust the OSD transparency shown on the display
Rotate: Default is “Off”, for others please request to your distributor or sales representative

Source Selection
Input Signal Selection:
Two Input are supported: Digital and Analog
If both digital and analog are connected, use the switch to select either Digital or Analog input
Auto Select: Default the OSD should auto detect the signal input
D-SUB：Input analog signal.
DVI：Input digital signal.
Display the video information presenting to the current states.
Information