Acnodes APW5460 User manual

APW5460
47” 1920 x 1080 Widescreen LCD
A l u m i n u m F r o n t B e z e l
W a l l M o u n t R e a d y
Industrial
Monitors
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA91710 Tel: [phone] Fax: [phone]
© Copyright 2015 Acnodes Corp.

Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing dam
age to other equipment or injury to persons nearby.
■When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■Observe all precautions and warnings attached to the equipment.
■If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being dam
aged by transient over-voltage.
■Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
■Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and invali
date its warranty.
■If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■Any product, on which the serial number has been defaced, modified or removed.
■Damage, deterioration or malfunction resulting from:
□ Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
□ Repair or attempted repair by anyone not authorized by us.
□ Any damage of the product due to shipment.
□ Removal or installation of the product.
□ Causes external to the product, such as electric power fluctuation or failure.
□ Use of supplies or parts not meeting our specifications.
□ Normal wear and tear.
□ Any other causes which does not relate to a product defect.
■Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-
lation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■Re-position or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Contents
< Part. 1 > APW5460
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Mounting Hardware & Installation
P.1
P.2 - 3
P.4
< Part. 2 > Specifications / OSD / Remote Controller
2.1 Product Specifications
2.2 On-screen Display Operation ( OSD )
2.3 Remote Controller ( RC-2 )
P.5 - 6
P.7 - 8
P.9
< Part. 3 > Options
3.1 Option Table
3.2 3G / HD / SD-SDI Broadcast-grade input
3.3 MCS Multi-display control solution
3.4 MIL-type or lockable connector
3.5 TV ( Analog )
P.10
P.11
P.12
P.13
P.14

Before Installation
■It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
■To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
■Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1 Disconnect the power cord.
2 Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1 Disconnect the power cord.
2 Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or applyany liquids directlyonto the monitor. Always applythe solution to your
microfiber cloth first, not directlyon the parts you are cleaning.
3 Gently wipe the surface. Use as little pressure as possible.
4 Wait until your monitor is completely dry before plugging it in and powering it up.

< Part 1 >
< 1.1 > Package Content
APW5460
47" FHD LCD display X 1
6ft VGA cable X 1
Power cord X 1
Remote controller X 1
Wall-mount bracket set X 1
Standard I/O
HDMI DVI-D Audio S-Video R CA Audio VGA Power
in out

< 1.2 > Structure Diagram -
1Front view
2
34
7
Bottom view
1 Rear case
2 LCD panel
3 6mm aluminum front bazel
4 Audio speaker, pair
5 LCD membrane
6 Wall-mount bracket
7 Remote sensor
5
Rear view
6
HDMI DVI-D Audio S-Video R CA Audio VGA Power
in out
Standard I/O : HDMI, DVI-D, Audio, S-Video + RCA, VGA
Options I/O : TV
SDI or MCS ( either one )
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
APW5460
1154 x 70.8 x 689 mm
45.1 x 2.8 x 27.1 inch
To be confirmed
35.1 kg
77.2lbs
41 kg
90.2 lbs

< 1.2 > Dimension

Front wall-mount bracket
Rear side
Rear wall-mount bracket
Wall
< 1.3 > Wall-mount Installation
Step 1
■Install left & right front wall-mount brackets at
the rear side of the LCD shown above.
■M5 screw x 8 pcs included ( Left & right side ).
Step 2
■Install left & right rear wall-mount brackets on
the wall shown above.
■6 x M10 screws required ( Left & right side ).
M10 screw sets are not provided.
Step 3
Wall
Wall LCD Wall
■Attach the LCD to the rear wall-mount brackets
on the wall.
Step 4
Installation Completed.
■No VESAmount provided for 46" and 55”
models. Only wall-mount available.

< Part 3 >
< 3.1 > Product Specifications
Mechanical
Design
APW5460
Front Panel
Black, RAL 9005
Rear Casing
Dark grey, RAL 7037
Other Mounting
Wall mount
Protection
3mm protective glass
LCD
Panel
Manufacturer
Panel Size ( diagonal )
47-inch Widescreen TFT color LCD
Display pixel ( dots x lines )
1920 x 1080
Brightness ( typ. )
350
Contrast Ratio ( typ. )
1400:1
Color
16.7 M
Viewing Angle ( L/R/U/D )
89/89/89/89
Response Time ( ms )
8
Dot pitch ( mm )
0.53
Display Area ( mm )
1040H x 585V
Surface treatment
Haze 2%, Anti-glare
Surface hardness
3H
Backlight Type
LED
MTBF ( hrs )
50,000
Video
Connectivity
Digital
HDMI
HDMI 1.1, CEA-861-D
DVI
DVI-D, TMDS single link
Analog
VGA
Analog 0.7Vp-p
Composite ( RCA)
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio
Connectivity
Audio Input
Connector
3.5mm stereo jack
Impedance / Power level
30kΩ / 750mV
Audio Output
Connector
3.5mm stereo jack
Resistance / Power level
30kΩ / 2.8V
Speaker Output
Power
2 x 10W
*When the audio output is connected, speaker output is OFF
Power
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON
130W or less
Power saving mode
9W or less
Power button OFF
2W or less

< 3.1 > Product Specifications
Regulatory
SafetyApproval
FCC & CE
Environmental
Conditions
Operating
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
Product ( W x D x H )
1145 x 70.8 x 689 mm
45.1 x 2.8 x 27.1 inch
Packing ( W x D x H )
To be confirmed
Net Weight
35.1 kgs / 77.2 lbs
Gross Weight
41 kgs / 90.2 lbs
Applicable
Format
DVI-D / VGA Input
PC Signal
1920 x 1080 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
HDMI Input
PC Signal
Same as VGA
Video Signal
1080p : 50 / 60Hz
1080i : 50 / 60Hz
720p : 50 / 60Hz
480p : 60Hz
576p : 50Hz
Audio Signal
2ch Linear PCM ( 32 / 44.1 / 48 KHz )
Composite / S-Video
Input
NTSC
525 lines, 60 fields / sec
PAL
625 lines, 50 fields / sec

< 2.2 > On-screen Display Operation ( OSD )
Power light
Green = On
Orange = Power saving
Membrane Switch Function
Power on / off LCD
Display the OSD menu
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button for 5 seconds)
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
2
PC
Auto adjust : Automatically adjust sizes, centers and fine tunes the
video signal to eliminate waviness and distortion.
Clock : Adjust the clock value
Phase : Adjust the phase value
H. Position : Align the screen image left or right
I. Position : Align the screen image up or down
1
Picture
Picture mode :
Standard / Vivid / Soft / User mode to choose
Brightness :
Adjust background black level of the screen image
Contrast :
Adjust the difference between the image background
(black level) and the foreground (white level)
Hue:
Adjust the screen hue value
Saturation :
Adjust the saturation of the image color
Picture size :
Adjust the image size
Color temp :
Standard / Cool / Warm / User to choose
Noise reduce :
Reduce the noise of the image
Sharpness :
Adjust the image from weak to sharp

< 2.2 > On-screen Display Operation ( OSD )
3
Audio
Audio mode : Movie / Voice / Normal / Music mode to choose
Volume : Adjust the volume of sound
Bass : Set the value of bass sound
Treble : Set the value of treble sound
Balance : Set the balance value of treble and bass sound
Analog TV audio : Set the value of analog TV audio sound
Mute : Turn off the surrounding sound
4
TV
Auto search : Automatically search
Manual search : Search the TV manual
Fine tune : Fine tune the TV signal
Color system : Adjust the TV color
Sound system : Adjust the TV sound
Channel edit : Edit the channel
5
MISC
Language : Select the language in which the OSD menu is
displayed - English
Sleep timer : Set the off time
PIP mode : Adjust picture in picture setting
PIP position : Enter into PIP position
PIP source : Enter into the Sub source and sound source
System reset : Return the adjustment back to factory setting
Information : Select for Help

< 2.3 > How to Use the Remote Controller
1 8
2
INPUT MUTE
VOL 9
7 BACK EXIT
PIP17
20
SOURCE
21
SWAP
PIP
POSITION PIP
AUDIO 18
19
r
1
INPUT
Select the source
2
Switches on or off the TV
3 0 - 9 Only use in TV mode. Select channels. For channel numbers 10
and above, enter the second digit within two seconds.
4 AUTO Auto adjust
5 MENU Display the menu on the screen or go to the previous menu
Go to the upper menu or select the previous value /
Go to the next menu or select the next value /
6 ▲/ ▼/ ◄/ ►/ ENTER Decrease the setting value /
Increase the setting value or enter to the select item setting
Enter to the select item settings or excude the setting
7
BACK
Back to previous value
8
MUTE
Turn on or off the speaker
9
Vol + / -
Increase or decrease the speaker volume
10
CH + / -
For TV model only, increase or decrease the channel number
11
FREEZE
Reserve for OEM model
12
- / --
For setting input single or double digits
13
ASPECT
Adjust the screen size
14
SELECT
To select the existing item
15
SLEEP
Select the sleeping time
16
EXIT
Exit the menu or cancel
PIP functions
17
PIP
Picture in picture
18
PIP AUDIO
To set the audio of in PIP mode
19
POSITION
To set the screen position in PIP mode
20
SOURCE
PIP Source
21
SWAP
Swap screen in PIP mode
1
2
3
3
4
5
6
7
8
9
CH
10
4
AUTO
0
-/--
FREEZE
11
12
5
MENU
SELECT
ASPECT
13
14
6
ENTER
SLEEP
15
16

< Part 3 > Options
< 3.1 > Option Table
Options
APW
SDI ***
MCS multi-screen control ***
MIL-type / lockable connector
TV
***
The user can only select either SDI or MCS inputs.

< 3.2 > Options : 3G / HD / SD-SDI input
Acnodes’ SDI input is an ideal solution for the broadcast-
grade video and high resolution CCTV market.
Designed for use with Full HD 1080p and ultra high resolution
1920 x 1200 LCD displays, Acnodes provides a SDI input
module without using additional space or power and it comes
standard with a 2-year warranty.
SDI
HDMI DVI-D Audio S-Video R C A Audio VGA Power
in out
in - out
INPUT
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equalized & relocked
Standard Compliance
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
Compatible Video Format
3G-SDI
1080p
@60 / 50Hz, 4:2:2
1080p
@30 / 25 / 24Hz, 4:4:4
1080i
@60 / 50Hz, 4:4:4
720p
@60 / 50Hz, 4:4:4
HD-SDI
1080p
@30 / 25 / 24Hz, 4:2:2
1080i
@60 / 50Hz, 4:2:2
720p
@60 / 50Hz, 4:2:2
SD-SDI
480i
@60Hz, 4:2:2
ITU-R BT.656
576i
@50Hz, 4:2:2
Compatible Audio Format
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
Max. Transmission Distance
75 ohm coaxial cable
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s

< 3.3 > Options : MCS
MCS
( Multi-display Control ) More control is always good. Especially when it is necessary and
easy. Acnodes provides MCS solution to control the OSD of
various LCD displayup to 64 units.
The RS-232C is used for the communication between the PC and
the first display via a 15 feet serial cable while the CAN bus is
used for the various LCD displays cascade together via CAT 5/6
cable, and daisychain up to 1,000 meters.
Designed for use with LCD displays, Acnodes provides a MCS
input module without using additional space or power and it
comes standard with a 2-year warranty.
MCS
HDMI DVI-D Audio
in
S-Video R C A Audio
out
VGA Power
Link in out set
*** Please download the protocol of MCS control at :
http://www.acnodes.com/files/downloads/MCS-UM.pdf
RS-232C
Set switch
For the 1st and last display,
push the set switch upward
15 feet serial cable
( over 15 feet, extender required )
For other daisy chain displays,
push the set switch downward
LINK OUT IN OUT IN OUT IN
OUT
RJ-45 jack
Cat5 / 6 cable
max. 300 meters
Cat5 / 6 cable
max. 300 meters
Daisy chain up to 1,000
meters and 64 displays
Cat5 / 6 cable
max. 300 meters
up to 64 displays

< 3.4 > Options : MIL-type or Lockable Connector
Input
Part no.
MIL Standard
MIL - type
Connector
DC Power ***
( Male )
MS3470W8-33P
MIL - DTL - 26482
VGA ***
( Male )
MS3470W14-15P
MIL - DTL - 26482
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design flexibility possible. For more information, please contact us.
Input
Part no.
Standard
Lockable
Connector
DC Power
( Male )
YM-Ext-461CP001
D-type 3W3
USB
LUSB - A111 - 00
-
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.

< 3.5 > Options : TV ( Analog )
HDMI DVI-D Audio
in
S-Video R C A
TV
Audio
out
VGA Power
***
For RC-2 remote controller specifications, please refer to P.13