Acoustic Energy Aelite User manual

Owner’s manual

Congratulations on choosing the Acoustic Energy AELITE One,
a powerful compact two-way loudspeaker which features
metal diaphragm technology and is capable of outstanding
performance. Please take a few moments to read this
manual. The advice it contains will enable you to get the very
best performance out of your Acoustic Energy loudspeakers.
The AELITE One utilises metal cone mid-bass drive unit technology,
proven in the AE Reference series. The rigid anodised alloy cone ensures
pure piston action and also acts as a heat sink for the bonded voice coil.
These features provide exceptional clarity, transparency, dynamics and
power handling.
The tweeter - or treble driver - is a high-quality neodymium unit with a
silk fabric dome integrating smoothly with the rest of the system.
All drive units are fully magnetically shielded so that the speakers
can be used in close proximity to a TV screen or monitor for AV
applications.
The Acoustic Energy AELITE One loudspeaker uses quality OFC
internal wiring, which enhances detail and transparency.
The AELITE One speakers are best heard with the tweeters at, or just
below, ear height when the listener is seated. For serious listening the
grilles are best removed.
Rigid support is essential for the speaker to develop its full detail and
dynamic performance. Rigid stands with spikes, cones or other methods
of secure mounting are recommended. Or wall mounting with a rigid
bracket.
Closeness to room boundaries has a major impact on the low frequency
performances. The speakers should be kept away from corners (which
will produce booming). The speakers can be positioned fairly close to a
back or side wall. If less than 6” a foam bung is supplied to minimise the
booming effect
Experiment with the best position to achieve a full, yet clean bass
response. Trust your judgement and ears.
For best stereo imaging the speakers should be as far apart as they are
from the listening position.
Positioning
Introduction

Bi-amping
Bi-amping adds a second amplifier to the system. One power amplifier
drives the treble section of both loudspeakers; a second drives the
mid/bass sections. Note that the shorting links must be
removed. Failure to do so will result in damaging the
amplifiers.
As regards the loudspeakers, wiring for bi-
amping is achieved in much the same way
as bi-wiring. Treble amplifier positive (red)
terminals should be connected via the
ribbed cable to
the positive (red) HF terminal on the speaker.
Similarly, treble amplifier negative is
connected to the negative (black) HF
terminal on the speaker. Repeat this
process with the mid/bass amplifier
and LF terminal pair.
After wiring up
Lower the volume to the minimum,
switch on the amplifier, select the signal source and
then raise the
volume to the listening level
required.
AMPLIFIER
LEFT SPEAKER
RETAIN LINKS
FOR FUTURE USE
RL
MAIN
Check that your amplifier is switched off before installing your
loudspeakers. Failure to do so may result in speaker or amplifier
damage. The diagram illustrates one loudspeaker only.
Conventional
Normal passive wiring requires shorting links to be in place between the
treble and mid/bass sections. The positive (ribbed) cable from the
amplifier positive (or red) terminal should connect with the positive
(red) terminal on the loudspeaker. Similarly the negative (smooth) cable
should connect the amplifier negative terminal (black) to the negative
terminal (black) on the loudspeaker.
Bi-wiring
Bi-wiring separates the bass and treble ground paths in the loudspeaker
and offer sound quality advantages. An extra set of cables is required.
Note that the shorting links are removed between the treble and
mid/bass sections and should be stored for later use if conventional,
passive driving is required.
Two pairs of cables are connected to the amplifier terminals. One cable
of each pair should connect to the treble section and one to the
mid/bass section. The positive (ribbed) cables from the amplifier positive
(or red) terminal should connect with the positive (red) terminals on the
loudspeaker. Similarly the negative (smooth) cables in each pair should
connect the amplifier negative terminal (black) to the negative terminals
(black) on the loudspeaker.
Connection

HF unit Neodymium tweeter with high
dispersion diaphragm.
Ferro fluid cooled and damped.
Magnetically shielded.
Exclusively profiled.
LF unit 110mm die-cast chassis. Lightweight
alloy cone with 32mm coil.
High-power, long-throw magnet
system. Magnetically shielded
Power Handling 100W max (undistorted program drive)
Frequency response ±3dB 45Hz to 23kHz
Frequency response ±6dB 55Hz to 21kHz
Sensitivity 89 dB/W
Impedance 8 ohm (6 ohm minimum)
Cabinet Real wood veneered. 15 mm MDF
wrap. Full circumferential brace. Front
firing, high power, low turbulence bass
reflex ports. 30 mm MDF front baffle.
Terminals Gold-plated 4-way binding posts.
Weight (excl. packaging) 6kg
Dimensions (WxHxD) 186 x 291 x 231 mm
Your Acoustic Energy loudspeakers are guaranteed against original defects in
materials, manufacture and workmanship for 3 years from the date of
purchase. Please retain all original packaging materials for possible future use.
We suggest that you complete details of purchase now and keep this
information in a safe place for future reference.
Under this warranty Acoustic Energy agrees to repair any defect or, at the
company’s discretion, replace the faulty component(s) without charge for parts
or labour. This warranty does not imply any acceptance by Acoustic Energy or
its agents for consequential loss or damage and specifically excludes fair wear
and tear, accident, misuse or unauthorised modification.
This warranty is applicable in the United Kingdom only and does not in any
way limit the customer’s legal rights. Claims and enquiries under the warranty
for AE products purchased outside the UK should be addressed to the local
importers or distributors.
If you have reason to claim under the warranty please contact your dealer in
the first instance.
Dealer’s name:........................................................................................................
Address:..................................................................................................................
................................................................................................................................
.................................................................................................................
Date of purchase:....................................................................................................
Serial numbers:.......................................................................................................
Acoustic Energy Limited
16 Bridge Road, Cirencester
Gloucestershire GL7 1NJ
Tel [phone]
Fax [phone]
Web www.acoustic-energy.co.uk
Specifications Warranty