ACT ACTPRO PRODUCT RANGE User manual

Ireland Oce
Unit C1, South City Business Centre,
Tallaght, Dublin, D24 PN28, Ireland
United Kingdom Oce
601 Birchwood One, Dewhurst Road,
Birchwood, Warrington, WA3 7GB, UK
Ireland: [phone]
UK: [phone]
Email: [e-mail]
www.act.eu
www.act-access.com (USA)
Copyright © 2016 Access Control Technology Ltd. Part No.18-00095 Iss 4
USB Desktop Reader
Operating and Installation
Instructions
pro
ACT Product Code: ACT USB Reader

1
Operating & Installation Instructions
Copyright © 2016 Access Control Technology Ltd. Part No.18-00095 Iss 4
Operating & Installation Instructions
1 System overview
The ACTpro USB reader is a plug and play desktop reader, with support for ACT RFID,
HID, MIFARE Classic and DESFire EV1 technologies and is compatible with ACTenterprise
versions 1.3.0.5 or later.
2 Installation
1. Install ACTEnterprise V1.3.0.5 or later.
2. Plug in USB reader into an available USB port.
3. Wait for the installation of the driver to complete.
4. Run ACTManage.
5. Present card to reader.
6. If the card is already assigned to a user, the user details page is displayed.
7. If the card is not assigned to a user, a new user details page is displayed with the card
number entered.
3 Speci󰘰cations
Learned Cards and Site Coded cards are not supported by the USB reader.
Features Description
13.56MHz technology MIFARE Classic, MIFARE Plus, MIFARE DESFire EV1
125kHz technology ACTRFID and HID
Dimensions 116 x 67 x 14mm / 4½” x 2¾” x ½”
Power Supply 5V DC- supplied from USB port
Current consumption <100mA
Audio Indication Buzzer when card presented
Visual Indication
Red LED on: Normal
GreenLED󰘱asheswhenvalidcardpresented
AmberLED󰘱ashing:notconnectedtoPC
Green LED Flashing: capture mode
USB Cable 1.5m / 4½ ft USB cable
FCC ID: 2AILRUSBRD
Model No. USB-RD
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
WARNING: Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

4 Non ACT MIFARE Cards:
The reader may be programmed to read non ACT MIFARE cards. From ACTInstall,
GotoACTInstall->AdvancedSetup->CardCon󰘰guration->MifareFormat
Select the appropriate MIFARE card type then press Save:
ACT MIFARE Card: This is the default setting to read ACT MIFARE Cards
Serial Operation: Returns the MIFARE serial number
Reverse Serial Operation: Returns the MIFARE serial number in reverse
DESFire EV1 ACT File Operation: Set when using ACT DESFire EV1 cards
OEM MIFARE card: Non-ACT MIFARE cards
OEM MIFARE card with MAD: Non-ACT MIFARE cards
5 Capture Cards:
For cards with both 125 kHz and MIFARE technology, cards should be enrolled using the
capture card facility in ACTManage -> Users
Click on the Capture card icon beside the card number.
To read the 125kHz number on the card, select “Read from USB Reader” and click
capture.
To read the ACT MIFARE number on the card, select “Read from MIFARE USB”
Reader and click capture.
2
Operating & Installation Instructions
Copyright © 2016 Access Control Technology Ltd. Part No.18-00095 Iss 4

Ireland Oce
Unit C1, South City Business Centre,
Tallaght, Dublin, D24 PN28, Ireland
United Kingdom Oce
601 Birchwood One, Dewhurst Road,
Birchwood, Warrington, WA3 7GB, UK
Ireland: [phone]
UK: [phone]
Email: [email protected]
www.act.eu
www.act-access.com (USA)
Copyright © 2016 Access Control Technology Ltd. Part No.18-00095 Iss 4
Access Control Technology Ltd. reserve
the right to change the contents of this
manual and the system it applies to
without prior notice.
Whileeverye󰘯orthasbeentaken
by ACT to ensure the accuracy of
the information contained within
this document, ACT assumes no
responsibility for any errors or
omissions. No liability is assumed
for damages resulting from the use
of information contained within this
document.