ACT ACTsmart2 1070 User manual

smart2
All ACT hardware is ISO9001 and CE certified by independent external certifiers.
Operating and Installation
Instructions
ACTsmart2 Product Range

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
Contents
ORDERING INFORMATION................................................................................................................ 4
INSTALLATION NOTES....................................................................................................................... 5
IMPORTANT ........................................................................................................................................ 5
PRODUCT SPECIFICATION ............................................................................................................... 5
30 SECOND PROGRAMMING GUIDE ............................................................................................... 6
ACTsmart2 Prox Only (1070) ................................................................................................... 6
ACTsmart2 Pin & Prox Only (1080) .......................................................................................... 7
ACTsmart2 Pin Only (1090)...................................................................................................... 8
PROGRAMMING SUMMARY ............................................................................................................. 9
ACTsmart2 OPERATION................................................................................................................... 10
ACTsmart2 PROGRAMMING ........................................................................................................... 10
Adding a Card Batch ............................................................................................................. 11
Deleting a Card Batch ........................................................................................................... 11
Adding a PIN.......................................................................................................................... 11
Deleting a PIN........................................................................................................................ 11
Adding a Card and PIN.......................................................................................................... 11
Deleting a Card and PIN........................................................................................................ 11
Adding a Card Batch using the keypad................................................................................. 12
Deleting a Card or Card and Pin using the keypad ............................................................... 12
Adding a Random Card......................................................................................................... 12
Set Door Relay Time.............................................................................................................. 12
Set Door Ajar Time ................................................................................................................ 12
Set Guest Buzzer Time.......................................................................................................... 12
Change Programming Code.................................................................................................. 13
Change Number of PIN Digits ............................................................................................... 13
Limit Number of Users........................................................................................................... 13
User Toggle............................................................................................................................ 13
Adding a Card Batch with Toggle mode................................................................................ 13
Adding a PIN Code with Toggle mode .................................................................................. 13
User Arm Function................................................................................................................. 14
Adding a Card Batch with Arming Function .......................................................................... 14
Adding a Pin Code with Arming Function ............................................................................. 14
Programming ACTsmart2 Options......................................................................................... 15
Setting Programmable Input Function................................................................................... 16
Setting AUX I/O 1 Function ................................................................................................... 16
Setting AUX I/O 2 Function ................................................................................................... 16
I/O Function Codes .............................................................................................................. 16
Quick I/O Setup ..................................................................................................................... 17
Aux I/O 1................................................................................................................................ 17
Adding a Card Batch for second door................................................................................... 18
Adding a PIN for second door............................................................................................... 18
Adding a Card and PIN for second door ............................................................................... 18
Adding random Card for second door................................................................................... 18

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
Contents
PROGRAMMING A NETWORK SYSTEM .........................................................................................19
Programming Door Numbers .................................................................................................19
Set a Master ...........................................................................................................................19
Assign Door Numbers ............................................................................................................19
Assign Users to Doors............................................................................................................19
Checking Network Programming ...........................................................................................19
Find Door Number ..................................................................................................................20
Find All Door Numbers ...........................................................................................................20
Adding a Slave to the Network...............................................................................................20
Removing a Slave from the Network......................................................................................20
Replacing a Slave Unit ...........................................................................................................20
Replacing the Master Unit ......................................................................................................20
RESTORING FACTORY DEFAULT ....................................................................................................20
PROGRAMMING ACTsmart2 PROX ONLY (1070) ...........................................................................21
Adding a Card Batch to the Network .....................................................................................21
Deleting Batch Cards to the Network.....................................................................................21
Deleting Individual Card (Require Card Above) ......................................................................21
Programming for Default IO....................................................................................................21
Programming the Door Relay Time ........................................................................................22
Programming for ACT Smart Lock .........................................................................................22
Default ACTsmart2..................................................................................................................22
DIAGRAMS
ACTsmart2 Standalone Wiring Diagram .................................................................................23
ACTsmart2 Interlock and Fire Override Wiring Diagram.........................................................24
ACTsmart2 Network Wiring Diagram......................................................................................25
ACT Smart Lock Connection Diagram ...................................................................................26
Alarm Wiring Diagram.............................................................................................................27
ACTpro-X Reader Wiring Diagram..........................................................................................28
2 Door Wiring Diagram ...........................................................................................................29
ACTsmart2 System Diagram ..................................................................................................30
ACTsmart2 Flush mounting Diagram......................................................................................31
ACTsmart2 Surface mount Diagram.......................................................................................32
User List..................................................................................................................................36
Proximity reader ACTsmart2 1070
PIN & Proximity reader ACTsmart2 1080
PIN Only reader ACTsmart2 1090
Smart Lock ACTsmart2 Lock
Proximity Fob ACTProx FOB-B
Proximity ISO Card ACTProx ISO-B
Proximity Half Shell Card ACTProx HS-B
Proximity & Mag Stripe Card ACTProx DUO-B
Controller ACTsmart2 controller
Software ACTWin Smart
Ordering Information/Product codes

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
Installation Notes
• Remember to Factory Default the ACTsmart2 before programming
• Remember to place the supplied varistor across the terminals of the door strike coil to
protect the relay contacts
• Don’t mount the ACTsmart2 Prox units near RF sources
(Eg mobile phones, radio transmitters, computer monitors) or metal surfaces.
• Remember that the ACTsmart2 PIN and Prox units default to Card operation. Card and
PIN operation must be programmed in. (See ACTsmart2 Programming Options
section, Options 39, 40 and 41).
• Don’t power the unit from a switch-mode power supply. Use a linear regulated power
supply.
• Never use the on-board relay to switch AC mains voltage. An external relay,
electrically isolated from the ACTsmart2 should be used for this purpose
• Remember to change the programming code.
• Don’t power the ACTsmart2 from an AC power supply on a networked system.
An AC power supply may only be used on a standalone ACTsmart2.
• The ACTsmart2 is not compatible with the original HID compatible ACTsmart.
The cards and fobs for one version will not work on the other. The ACTsmart and
ACTsmart2 devices may NOT be networked together.
• When ordering new cards or fobs specify ACTsmart2.
Important
As with any Access Control system, always ensure there is an alternate means of escape
in the event of the unit failing to operate due to power loss or in the event of re.
Product Specification
Number of Users 500 users in Card and PIN mode. 1000 users otherwise.
Supply Voltage 12 - 24 V DC (linear PSU) or AC (standalone only)
Current Consumption 60mA (nominal), 100mA (maximum)
Output Current Sink 100mA
Operating Temperature -25 to +60 degrees C
Door Open Time 0 - 255 seconds
Max. ACTsmarts per network 8
Length of network 1.4km maximum
Relay Contact Rating 5A / 38Vac
Programmable Inputs 1
Programmable Input/Outputs 2
Controller Size Flush Mount (W x H x D, mm) 100 x 110 x 20
Surface Mount (W x H x D, mm) 100 x 110 x 35
Controller Weight 200 grams
Water Resistance High IP67
Construction Rugged Polycarbonate housing with stainless steel keys and
potted electronics.
1

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
30 Second Programming Guide
ACTsmart2 Prox Only (1070)
(For typical Standalone System)
1. Choose Programming Card.
Select any proximity card or fob as the programming card (it is recommended to use the
lowest numbered card in the batch). The card will only be used for programming and
cannot be used to gain access.
2. Remove tamper and LK1 from the ACTsmart2
Make sure the ACTsmart2 is not powered up and remove the unit from the mounting plate
or the surface mount collar (this opens tamper) and also remove LK1 at the back of the
unit.
3. Assign the Programming Card
Apply power to the unit and within 10 seconds present the programming card. The unit
will beep. Take the programming card away from the unit (more than 20cm). Within a fur-
ther 10 seconds replace LK1. The unit will beep.
The card is now programmed.
Replace the ACTsmart2 on the mounting plate / surface mount collar to close tamper.
4. Add a Card Batch
Present the Programming card followed by the rst card in the batch followed by the last
card
(highest numbered).
5. Store Programming Card
Put the Programming Card in a safe place in case it is required later to add or remove
cards. The ACTsmart2 is now ready for normal use.
For more information on programming the advanced features of the ACTsmart2
1070, please refer to the complete programming guide.
2

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
30 Second Programming Guide
ACTsmart2 Pin & Prox (1080)
(For typical Standalone System)
1. Enter Programming Mode.
Press abutton followed by the programming code (default is 9999) The LED will ash
amber.
2. Add a Batch of Cards
Press 10, then present the rst card in the batch followed by the last card in the batch.
Press abutton to complete.
3. Add a PIN Code
Press 12, and then enter a 4-digit PIN code. Press abutton to complete.
(Option 40 - Card or PIN.)
4. Set Desired Door Relay Active Time
Press 20, and then enter the desired number of seconds from 000-255 (three digits with
leading zeros). Press abutton to complete. The default time is 5 seconds.
5. Change Programming code
Press 23, then enter new 4-digit programming code. Press ato complete
6. Exit Programming Mode
Press the rbutton. The LED turns red. The ACTsmart is now ready for normal use.
Note: The ACTsmart2 may be returned to its factory default condition at any time by
entering the programming mode and pressing 80 followed by the abutton.
For information on programming the advanced features and networking the
ACTsmart2 range, please refer to the complete programming guide.
3

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
30 Second Programming Guide
ACTsmart2 PIN Only (1090)
1. Enter Programming Mode.
Pressabutton followed by the programming code (default is 9999) The LED will ash
amber.
2. Add a PIN Code
Press 12, and then enter a 4-digit PIN code. Pressabutton to complete.
3. Set Desired Door Relay Active Time
Press 20, and then enter the desired number of seconds from 000-255 (three digits with
leading zeros). Pressabutton to complete. The default time is 5 seconds.
4. Change Programming code
Press 23, then enter new 4-digit programming code. Pressato complete.
5. Exit Programming Mode
Press the rbutton. The LED turns red.
Note: The ACTsmart2 may be returned to its factory default condition at any time by
entering the programming mode and pressing 80 followed by theabutton.
For information on programming the advanced features and networking the
ACTsmart2 range, please refer to the complete programming guide.
4

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
Code Function Default
10 Add Card Batch
11 Delete Card Batch
12 Add PIN Code
13 Delete PIN
14 Add Card and PIN
15 Delete Card and PIN
16 Add Card Batch using keypad
17 Deleting a Card or Card and Pin using the keypad
18 Add Random Card
20 Set Door Relay Time 5 seconds
21 Set Door Ajar Time 30 seconds
22 Set Guest Buzzer Time 2 seconds
23 Change Programming Code 9999
24 Change Number of PIN Digits 4
26 Limit Number of Users 1000
30 Door Chime Off
31 Silent Operation Off
32 Lock-saver (Anti Tailgating) Off
33 Toggle Off
34 Door Forced Alarm On
35 Door Ajar Alarm On
36 Guest Button On
37 Duress Codes Off
38 Network Master Off
39 Card and PIN Off
40 Card or PIN Off
41 Card and any PIN Off
43 Pulse Door Armed Off
44 Permanent Backlight On
45 Automatic Backlight Off
50 Set Programmable Input Door Release Button
51 Set AUX I/O 1 Door Contact
52 Set AUX I/O 2 Door Alarm
53 Quick I/O Setup
60 Assign Door Numbers
61 Find Door Number
62 Find Door Numbers
70 Add Card Batch for Second Door
71 Add PIN code for Second Door
72 Add Card and PIN for Second Door
73 Add Random card for Second Door
80 Default Unit
Programming Summary
5

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
ACTsmart2 Operation
The ACTsmart2 family consists of Proximity Only (ACTsmart2 1070), Pin and Proximity
(ACTsmart21080) and PIN Only (ACTsmart2 1090) units. Each ACTsmart2 can operate in
standalone mode or up to 16 ACTsmart2 devices can be connected on a RS485 network.
The ACTsmart2 will support a maximum of 1000 tokens. A token may be a card, keyfob or
a PIN code. Each unit is contained in a rugged polycarbonate housing, with stainless steel
keys, and potted electronics, allowing for indoor and outdoor installation.
Programming the unit is achieved via the keys and LED. For quick and easy installation, the
ACTsmart2 has a default conguration, which is suitable for most installations. Cards and
PIN codes can be programmed into the ACTsmart2 very quickly. ACT recommends that
the user keep track of the Cardholders and PIN users on the system by using the User List
at the end of the manual. Make copies of this sheet and enter all User details on it. This
will allow users to be deleted later on, even if a card is lost or a user forgets their PIN code.
Additional User Lists can be downloaded from the resource section of our website at www.
act.eu.
To improve security, PIN codes can be increased from 4 to 6 digits in length. Normally only
card users are allowed access through the ACTsmart2 PIN and Prox unit. For maximum
security, the unit may be programmed to require all users to enter a PIN code after presenting
a card. For lower security applications, another programming option allows access to PIN
only users. A duress code feature is also available
The built-in inputs and outputs are programmable, allowing the ACTsmart2 to be used in
a wide variety of applications from simple door access, to cash ofces and re exits. Each
unit also has built-in tamper monitoring for improved security.
ACT also provide an easy-to-use PC application (ACTWinSmart), which allows the installer
to congure systems quickly. Up to 8 ACTsmart2 units may be connected to the PC. The
end-user may also use ACTWinSmart to monitor day-to-day activity, add new users etc.
ACTsmart2 Programming
Press the rbutton followed by the programming code (initially 9999). The LED will ash
amber while in programming mode. If ris pressed at any time or no key is pressed within
30 seconds, programming mode is exited. If the LED ashes green during programming,
then a card presentation is expected. If the LED ashes red, then a keypress is expected.
While the ACTsmart2 is busy performing a task, (Eg. Defaulting memory, adding cards), the
green led will turn on and the buzzer will sound an elongated tone.
Note: In most Programming Menus there is a step that is marked (optional)*. This
setting only applies to a Networked System (see Programming a Network System).
6

ACTsmart2 Operating and Installation Manual Rev. 2
Copyright © 2015 Access Control Technology Ltd.
Step Keypad Entry Operation
1 10 Add Card Batch
2 Present Card First card in Batch (lowest number card)
3 Present Card Last Card in Batch (highest number card)
4 Enter 1-8, (optional)* Select each door this batch enabled for
5Press aEnd programming card batch -
Note: the buzzer will sound while cards are loaded into memory.
Step Keypad Entry Operation
1 11 Delete Card Batch
2 Present Card First card in Batch (lowest number card)
3 Present Card Last Card in Batch (highest number card)
4 Enter 1-8, (optional)* Select each door this batch deleted from
5Press aEnd delete card batch -
Note: The buzzer will sound while cards are deleted from memory.
Adding a Card Batch:
Deleting a Card Batch:
Step Keypad Entry Operation
1 13 Delete PINs
2 0001-9999 4 - 6 digit PIN code
3 1-8, (optional)* Select each door this PIN is deleted from
4Press aEnd deleting PINs
Deleting a PIN:
Step Keypad Entry Operation
1 12 Add PINs (Make sure Option 40 is set on PIN and Prox units.)
2 0001-9999 4 - 6 digit PIN code
3 1-8, (optional)* Select each door this PIN is valid for
4Press aEnd programming PINs
Adding a PIN:
Step Keypad Entry Operation
1 14 Add Card and PIN (Make sure Option 39 is set on PIN and Prox units.)
2 Present Card
3 0001-9999 4 - 6 digit PIN code
4 1-8 (optional)* Select each door this Card & PIN is valid for
5Press aEnd programming Card and PINs
Adding a Card and PIN:
Step Keypad Entry Operation
1 15 Delete Card and PIN
2 Present Card
3 1-8, (optional)* Select each door this Card & PIN is deleted from
4Press aEnd deleting Card and PINs
Deleting a Card Batch:
7