ACT TLM User manual

IOM-100 v2
TLM Modular Baghouse
Installation and Operation Manual

2
ACT Dust Collectors
CAUTION!
Accidents happen, be careful and always follow all local and federal regulations!
Fires and explosions do occur in dust collectors. Many items in a dust form can become very flammable and/or
explosive. It is very important that when installing a dust collector to check with and abide by all local and federal
regulations. Precautions such as spark traps, detectors, and extinguishers are always recommended when sparks or
explosive danger is present. Never throw any burning objects into the duct work or dust collector. There is no way to
guarantee 100% prevention of fires. However, the methods mentioned above will greatly reduce your risk. ACT
Dust Collectors will not be responsible in any way for any loss or damage associated with fires or explosions in your
dust collector.
If your dust collector came with explosion vents or if explosive dusts are present, it is the owner’s/operator’s
responsibility for full compliance with all authorities having jurisdiction. It is recommended that the NFPA codes be
studied and applied, including, but not limited to 68, 69 and 654. Included in the NFPA standards is the issue of
isolating your dust collector. Please contact us or an expert in the area regarding isolation of your dust collector in
the event of an explosion. Unless a Kst test was performed, and we were provided with the results, the size of the
explosion vents may be inaccurate and you may not be in compliance. It is the owner/operators responsibility to
verify the Kst and Pmax values. We recommend that your process be evaluated regularly to make sure that you
remain in compliance and the vent area is sufficient. ACT Dust Collectors will not be responsible for ANY loss
whatsoever resulting from an explosion associated with an ACT dust collector.
Dust collectors are tall and top heavy. Always be careful when handling them. Make sure your equipment is capable
of making the lifts and moves you are trying to make. Be sure the foundation for the dust collector is proper and
secure.
All plumbing and electrical should be performed by certified professionals and meet all codes and regulations.
Never open any doors or access panels while the machine is in operation.
Always shut down the unit prior to service and lock out all disconnects.
Always wear proper safety equipment when working on or around your dust collector and follow all local and federal
codes.
Dust Collector
Model: _____________________________________ Serial Number: _________________________________
Filters: _____________________________________ Ship Date:_____________________________________
Option/Accessories: __________________________________________________________________________
Fan Blower
Manufacturer/Model: __________________________ Serial Number _________________________________
Product Datasheet

3
TLM Baghouse
Table of Contents
Introduction.................................................................................................................................................................4
Operation Principle.....................................................................................................................................................5
Shipping and Receiving .............................................................................................................................................6
Handling ..................................................................................................................................................................... 6
Assembly
Hopper and Legs...........................................................................................................................................7
Filter Housing Middle Section .......................................................................................................................7
Filter Housing Top Section............................................................................................................................ 8
Multiple Modules - Hopper ............................................................................................................................8
Multiple Modules - Middle Filter Housing ......................................................................................................9
Multiple Modules - Top Filter Housing ..........................................................................................................9
Ladders and Railings ..................................................................................................................................10
Bags and Cages Installation - Blowpipe Removal ......................................................................................11
Bags and Cages Installation - Continued....................................................................................................12
Compressed Air ..........................................................................................................................................12
Electrical...................................................................................................................................................................13
Timer Board Programming.......................................................................................................................................13
Maintenance
Bags Replacement......................................................................................................................................14
Troubleshooting .......................................................................................................................................................16
Warranty...................................................................................................................................................................18

4
ACT Dust Collectors
Introduction
Thank you for your purchase of an ACT dust collector. Our goal is to provide you with a product of best quality,
service, and pricing in the industry.
This manual is to provide general instructions in assisting you with your installation, operation, and maintenance of
your equipment. It is the user’s responsibility to ensure that the equipment is correctly installed and operated. It is
also the user’s responsibility to ensure and provide qualified personnel for the installation, operation, and
maintenance of the equipment and to adhere to all applicable federal and local building and safety codes and
regulations.
Any special instructions and certified drawings accompanying this equipment shall supersede this manual.
Keep this manual along with any special instructions and drawings necessary for assembly, operation, and
maintenance with the equipment.

5
TLM Baghouse
Operation Principle
The TLM baghouse is a pulse-jet, fabric filter, air cleaning device that removes the particulates from dust-laden air
and allows clean air to be exhausted. As air enters through the hopper inlet, the particulates experience a reduction
of velocity, which causes the heavier particulates to fall down into the hopper. The remaining dust is directed
upward towards the filter bags where the dust is collected on the filters, allowing clean air to be exhausted. As the
dust accumulates on the filters and forms a dust cake, the efficiency of the filter bags increases.
To remove excess dust buildup, a timer board is used to sequentially open the solenoid and diaphragm valves that
release a pulse of compressed air through the blowpipes and downward into the filter bags. This pressure pulse
releases the excess dust on the filters, allowing it to drop down into the hopper.
Hopper Inlet
Bag Filters
Blowpipes

6
ACT Dust Collectors
Shipping and Receiving
All products from ACT Dust Collectors are carefully inspected for quality and order completion prior to shipment.
Prior to unloading, inspect all components for any shipping damage and missing parts. Report and file a claim
immediately with the carrier for any damage or missing items. Once filed, contact your ACT Dust Collectors
representative to notify them of your issue(s).
Any repairs to components with minor damage from transit must be approved in writing by the manufacturer.
Handling
Handling should be performed by trained, able, and qualified personnel and be consistent with safe handling
practices outlined by OSHA and local codes.
Review this manual and any additionally supplied certified drawing(s) to familiarize yourself with the lift points of
each of the components.
Verify the integrity and lift capacity of all handling equipment/components.
When handling the housing, it is recommended to utilize spreader bars to prevent any deformation during lifting.
All lifting points are to be used.
Table 1 - Recommended SAE Torque Table
Bolt Size SAE Grade 5 Torque (ft-lb), dry
1/4-20 8.4
5/16-18 17.4
3/8-16 31
7/16-14 49
1/2-13 75
5/8-11 150
3/4-10 267

7
TLM Baghouse
Assembly
Hopper and Legs
1. Lift the hopper using a crane along its four lift points.
2. Locate and fasten the legs along the corners of the
hopper with the supplied hardware. Hand tighten the
hardware while keeping the hopper supported with
the crane.
3. Locate and fasten the leg bracings to the legs. Hand
tighten the hardware.
5. Fasten the middle of the leg bracings that cross one
another.
6. Install 3/4 inch diameter anchor bolts with a minimum
1 3/4 inch extension above the foundation.
7. Once the hopper and legs have been assembled and
anchored, tighten all of the fasteners to the
recommended SAE torque per Table 1.
Filter Housing - Middle Section
1. Apply the supplied gasket sealing tape to the hopper
flange on to the inner side of the bolt pattern.
2. Lift the filter housing middle section with a crane
along its four internal lift points and align it to the
hopper flange (It is recommended to utilize spreader
bars to prevent any deformation).
3. Fasten the housing to the hopper. Hand tightening
only.
4. Once all fasteners are installed and the middle
section is properly aligned, tighten all fasteners.
Middle Housing - Hopper - Legs Assembly
Spacer
Housing
Gasket Sealing Tape
Hopper
Leg
Leg Bracing
Hopper
Lift Point
Middle Filter Housing
Internal Lift Lugs

8
ACT Dust Collectors
Filter Housing - Top Section
1. Apply the supplied gasket sealing tape to the middle
filter housing flange on to the inner side of the bolt
pattern.
2. Lift the filter housing top section with a crane along
its four lift points and align it to the middle filter flange
(It is recommended to utilize spreader bars to
prevent any deformation).
3. Fasten the top housing section to the middle section.
Hand tightening only.
4. Once all fasteners are installed and are properly
aligned, tighten all fasteners.
Multiple Modules - Hopper
1. Completely assemble one hopper so that it is self-
supporting.
2. Lift the second hopper to be installed next to the first
hopper.
3. Fasten the second hopper to the first hopper along
the mating side so that they share one leg.
4. Complete the leg assembly for the second hopper.
Top Filter Housing
Multi - Hopper Assembly
Lift
Lift

9
TLM Baghouse
Multiple Modules - Middle Filter
Housing
1. Apply the supplied gasket sealing tape to the
hopper flange and the mating flange of the middle
filter housing. Locate gasket to the inner side of
the bolt pattern.
2. Lift the filter housing middle section with a crane
along its four internal lift points and align it to the
hopper flange (It is recommended to utilize
spreader bars to prevent any deformation).
3. Fasten the housing to the hopper.
4. Lift the second middle section and align it to its
respective hopper and to the mating side flange of
the previous section.
5. Fasten the second middle section to the hopper
and previous middle section.
Multiple Modules - Top Filter
Housing
1. Apply the supplied gasket sealing tape to the
middle filter housing flange and the mating flange
of the top filter housing. Locate gasket to the inner
side of the bolt pattern.
2. Lift the filter housing top section with a crane along
its four lift points and align it
to the middle filter flange (It
is recommended to utilize
spreader bars to prevent
any deformation).
3. Fasten the top housing
section to the middle
section.
4. Lift the second top section
and align it to its respective
middle section and to the mating side flange of the
previous section. While in this process of
alignment, the 1” NPT header coupler should be
installed to connect both header assemblies.
5. Fasten the second top section to its middle section
and previous top section.
Filter Housing Middle Module Assembly
Lift
Lift
Filter Housing Top Module Assembly
Header
Coupler

10
ACT Dust Collectors
Ladders and Railings
1. Ensure that the filter housing, hopper, and legs are
securely tightened prior to ladder and railing installa-
tion
2. Locate, mount, and hand fasten the guard rails to the
collector.
3. Fasten the guard rails together.
4. Once all guard rails have been mounted, install the
ladder and cage.
5. Tighten all fasteners to the proper SAE torque.
Safety Railings
DETAIL “A”
DETAIL “B”
Guard Rails
A
B
Ladder Assembly
Ladder and Cage
Assembly

11
TLM Baghouse
Bag and Cage Installation
Blowpipe removal
1. The blowpipes are installed prior to shipping and
must be unfastened and pin-locked in the upright
position for bag and cage installation.
2. Open the filter access doors to gain access to the
clean air plenum by unfastening the knobs by hand.
3. Carefully raise the door up and secure the hinge by
engaging the lock.
4. Carefully step down onto the tubesheet.
5. Loosen by hand the dresser nut on bulkhead
connector from the inside
6. Undo the pin connector on the opposite end of the
blowpipe.
7. Once the blowpipe is loosened, slide it back and out
of the bulkhead connector and raise it up 90
degrees. Re-insert the pin connector to hold the
blowpipe in its upright position.
Opening and Securing
Filter Access Doors
Lift Door
Hinge Safety Lock
Blowpipe Removal/Installation
Bulkhead
Connector
Pin Connector
Blowpipe
Tubesheet

12
ACT Dust Collectors
Bag and Cage Installation
Continued
1. Insert the filter bag into the tubesheet hole.
2. Manipulate the snap band end of the filter bag into
the shape of a half moon as you insert the bag onto
the tubesheet such that the tubesheet is located be-
tween the two ridges of the snap band.
3. Center the filter bag in the tubesheet hole.
4. Insert the cage into the filter bag and firmly press
down to secure it.
5. Reinstall the blowpipes and secure the filter access
doors
Compressed Air
The supplied compressed air must be clean, dry, and oil-
free. Set the compressed air pressure levels to 90-100
psi. Do NOT exceed 100 psi as damage may occur to
the components.
Prior to installation, purge the compressed air lines of
any dirt or buildup.
1. Install the pipe line to the air manifold. Use thread
sealant tape or compound on all connections.
2. It is recommended to install a shut-off valve, pres-
sure regulator, safety exhaust valve, and filter along
the pipe line leading to the manifold.
Filter Bag and Cage
Tubesheet
Opening
Filter Bag
Tubesheet
Filter Bag
Bag Cage
Solenoid Valves
1” NPT Female
Diaphragm Valves
Air Manifold
Pulse-Jet Cleaning System

13
TLM Baghouse
Electrical
All wiring should be done by a certified electrician and in accordance with all local and federal codes.
Refer to the job specific electrical drawing(s) located in the panel and manual binder for detailed instructions.
Fan and timing board/solenoid wiring are to be in separate conduits.
1. Fan
 Verify fan rotation by observing motor rotation from the motor end and comparing it to the rotation arrow
on the fan. Another indication is poor fan performance or a lack of air movement.
2. Timer Board
 Locate the timer board as close to the dust collector as possible.
 To wire the timer board, please refer to the wiring diagram located inside the timer board enclosure.
 Once the timer board has been installed, the pressure gauge must be connected to the dust collector
using customer supplied ¼” tubing (clean air plenum = “ - ”, dirty air plenum = “ + ”). If the dust collector
is installed outside, the tubing should UV resistant.
 IMPORTANT: Prior to operating the dust collector or adjusting the settings, ensure that the
down time clean feature has been properly wired. This feature will allow the dust collector to clean itself
during shut down, which will aid in prolonging the life of the filters.
Timer Board Programming
Familiarize yourself with the timer board manual before programming the timer board. The table below summarizes
the recommended settings. Consult with ACT Dust Collectors for specific applications.
Table – Recommended Timer Board Settings
Feature Settings
Process Current pressure drop
Last Output The highest output terminal value that has a wire installed in it. Terminal out- puts have a range from 1-22 and are found near the
bottom of the timer board.
Time Off 10
Time On 100
High Limit 1.50” above initial pressure drop
(Contact Manufacturer for Questions)
Low Limit 1” below high limit
High Alarm 10 (Unless alarm is installed - Consult Manufacturing)
Low Alarm 0 (Unless alarm is installed - Consult Manufacturing)
Cycle Delay 0
Down Time Cycles 10
Auto Alarm Reset Unless notified, leave at factory setting of 5.

14
ACT Dust Collectors
Maintenance
Bag and Cages Replacement
Blowpipe removal
1. Prior to maintenance, lock out and tag all electrical
connections.
2. Open the filter access doors to gain access to the
clean air plenum by unfastening the knobs by hand.
3. Carefully raise the door up and secure the hinge by
engaging the lock.
4. Carefully step down onto the tubesheet.
5. Loosen by hand the dresser nut on bulkhead
connector from the inside
6. Undo the pin connector on the opposite end of the
blowpipe.
7. Once the blowpipe is loosened, slide it back and out
of the bulkhead connector and raise it up 90
degrees. Re-insert the pin connector to hold the
blowpipe in its upright position.
Opening and Securing
Filter Access Doors
Lift Door
Hinge Safety Lock
Blowpipe Removal/Installation
Bulkhead
Connector
Pin Connector
Blowpipe
Tubesheet

15
TLM Baghouse
Bags and Cages Replacement
Continued
1. Lift the cage up and out of the filter bag
2. Manipulate the snap band end of the filter bag into
the shape of a half moon and release the filter from
the tubesheet until it falls down into the hopper.
3. Remove the dirty bags from the hopper through the
hopper access door.
4. From the clean air plenum, insert the filter bag into
the tubesheet hole.
5. Manipulate the snap band end of the filter bag into
the shape of a half moon as you insert the bag onto
the tubesheet such that the tubesheet is located be-
tween the two ridges of the snap band.
6. Center the filter bag in the tubesheet hole.
7. Insert the cage into the filter bag and firmly press
down to secure it.
8. Reinstall the blowpipes and secure the filter access
doors
Filter Bag and Cage
Tubesheet
Opening
Filter Bag
Tubesheet
Filter Bag
Bag Cage

16
ACT Dust Collectors
Troubleshooting
Problem Probable Cause Solution
Poor performance - not enough
suction or air movement Fan rotation in wrong direction Rewire three phase wires to change fan rotation
Closed damper or obstruction in
airstream Slowly open damper or remove obstruction
VFD Verify settings and operating
speed
System design Verify fan performance to fan
curve with airflow, static pressure,
and amperage readings
Re-evaluate system design to
verify that the fan is properly sized
for the application or nothing has
changed since product selection
(i.e. added a new weld station)
System effects Check along the duct system to
ensure that there is no abrupt
changes in airflow (i.e. inlet box
with no turning vanes, mitered
elbow with no vanes, etc.)
Filters at end of life Replace filters
Not enough compressed air Verify that the pressure is high
enough for effective cleaning (set
to 90-100 psi)
High differential pressure Dirty filters Activate cleaning by reducing the
"high limit" or manually pulse by
following the instructions in timer
board manual
Replace filters near end of life
Not enough compressed air Verify that the pressure is high
enough for effective cleaning (set
to 90-100 psi)
Defective cleaning system Verify solenoids, diaphragm
valves, and timer board are
functioning and properly wired
Motor over-amping Fan design Overloading radial-bladed fans
may require a damper to reduce
the horsepower requirements
Electrical Verify correct motor supply voltage
Fan/motor sized incorrectly Confirm system requirements with
airflow measurements
Replace fan with larger unit

17
ACT Dust Collectors
Troubleshooting Continued
Problem Cause Solution
Zero differential pressure
reading Wrong pressure high/low pressure tubing connection Swap the connections of the pressure reading plastic tubing on
the side of the collector
Pressure reading tubing kink or
leakage Inspect tubing for kinks or leakage
Filters/Bypass Verify filters are installed and that
there is no bypass of dust
Defective timer board Replace board. (1-800-422-1316)
Cleaning system not pulsing Solenoid Listen for clicking noise to verify
solenoids are opening/closing.
Replace if defective.
If located in frigid outdoors
temperatures, a solenoid heater
may be required
Diaphragm Valve Replace worn diaphragms.
(1-800-422-1316)
Timer board Manually pulse by following
instructions in timer board manual.
Verify it is correctly installed.
Defective. Replace board. (1-800-
422-1316)
No down-time cleaning Timer board Verify settings on timer board
Electrical Call A.C.T. to verify electrical
drawings and specifications.
(1-800-422-1316)
Dust discharging from outlet Filter damage Inspect filters for tears along filter
media and gaskets.
Pulse pressure set too high Decrease compressed air
pressure.

18
ACT Dust Collectors
Warranty
Air Cleaning Technology, Inc. warrantees the equipment to be free from defects in materials and workmanship for a
period of 10 years from the date of purchase. This warranty does not cover any damage due to normal wear and
tear including, but not limited to, corrosion, abrasion, elements, and modifications. This warranty covers parts only.
This warranty covers only the parts manufactured exclusively for Air Cleaning Technology, Inc. All other parts will be
covered by individual manufacturer’s warranty.
For Questions and Replacement Parts
Call Toll-Free 800-422-1316

 N  S 
N  U  N 



