Oneida Air Systems Super Dust Gorilla User manual

OneidaAir Systems, Inc. 1001 West Fayette St., Syracuse, NY13204
Phone [phone].476.5151 Fax [phone] www.oneida-air.com
Shown with
optional Stand.
Models may vary slightly
in appearance.
6_10
SuperGorillaOwner’sManual
2hp50Hz
CyclonicDustCollector
2hp50Hz

1
2hp 50hz Super Gorilla Owner’s Manual © O.A.S. 2010
Thank You for Choosing an Oneida Air Systems Product!
OAS manufactures and sells dust collection equipment only. Our qualified technicians and sales staff are available
7:30am - 6:00pm EST Mon. -Thurs. and 7:30am - 5:00pm EST Fri. to answer any questions concerning OAS products
and dust collection. Call for ductwork design and ductwork quotes, including system pricing and shipping cost.
Read the entire Owner’s Manual before installing or operating system!
Proudly Made
in the USA
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
X.
XI.
XII.
XIII.
XIV.
XV.
XVI.
XVII.
XVIII.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
System Start-Up Information
Commercial Configurations
General Specifications & Fan Performance Curve
Dimensions
General Assembly
General Assembly Instructions
Bracket Assembly
Filter Assembly
Filter Maintenance
Directions for Cleaning External Filter & Clipping Dust Pan
Fan / Blower Wiring Diagram
Troubleshooting
Fire Hazards - Read Before Installing System
Terms and Conditions
Stand Assembly
Accessories
Fan Motor Maintenance
Optional Remote Controller Diagram
TableofContents Page

22hp 50hz Super Gorilla Owner’s Manual © O.A.S. 2010
I.SystemStart-UpInformation
The Dust Collector & Fan / Blower is heavy! Handling and installation should always be performed
by experienced and trained personnel who have experience with rotary equipment. In addition to
the following instructional manual, care should be taken to ensure compliance with specific safety
requirements mandated by federal, state and local codes.
1. Read the installation and maintenance instructions as well as the recommended safety practices in this
manual
3. Motor is pre-wired at the factory. If magnetic starter trips circuit, check the following:
1. Dust drum securely fastened to discharge of cone?
2. Is ductwork installed at cyclone inlet?
2. Install ductwork completely before operating collector:
A.) Seal ductwork with silicone sealant or duct tape.
B.) Have dust bin in place and sealed.
Caution
Warning
Warning
Do not operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in
place. Dust Drum and Cyclone must be in place and sealed or motor will overheat!
If amperage is too high - shut down immediately! See Troubleshooting section.

3
2hp 50 hz Super Gorilla Owner’s Manual © O.A.S. 2010
II.Super DustGorillaConfigurations
Shown with
optional Stand.
1. External Cartridge Filter - Silencer Included with Filter
Caution:
Cartridge Filter Media
If exhaust air is vented outside you must provide make up / return air.
Flue gases (carbon monoxide) can be drawn into the shop from furnaces,
water heaters or other appliances.
99cm / 8.83 Sq. Meters
GE H12 Certified HEPAfilter media.

42hp 50hz Super Gorilla Owner’s Manual © O.A.S. 2010
III.GeneralSpecifications&FanPerformanceCurves

5
2hp 50hz Super Gorilla Owner’s Manual © O.A.S. 2010
IV.Dimensions
For Minimum Mounting Heights w/ 99 cm Filter
*Dimensions subject to slight variation in manufacturing.
2 & 2.5hp -
92.00”
6
33 cm
33.0 cm
123 cm
61.6 cm
67.5 cm
Allow 2.5 - 5 cm from ceiling
231.1 cm
191.8 cm
168.9 cm
142.2 cm
40.0 cm
20.3 cm
99.0 cm
15.2 cm
132.5 liter shown
Add 33 cm for 208.2 liter 10 cm

62hp 50hz Super Gorilla Owner’s Manual © O.A.S. 2010
V.GeneralAssembly
Optional 35 & 55 Gal. Stand
(4) Rubber Leg Caps - RCR012500
(4) Top Gussets - RFG010000
(4) Mid-Gussets - RFG010001
(4) Stand Braces - SXX000000
(4) 35 Gal. Leg Set - SXX000035 or
(4) 55 Gal. Leg Set - SXX000055
Stand Hardware Kit -
AHX000100
(16) 1/4”-20 x 2” bolts
(16) 1/4”-20 x 3/4” bolts
(32) 1/4” flat washers
(32) 1/4”-20 Nylock nuts
f9. (16) Clips -AFT051618
AHX000001
40
12
f10. (16) Flange Bolts -AFB155155
(8) 5/16” Clips
(8) 5/16” Bolts
(8) 5/16” Clips
(8) 5/16” Bolts 5i
5i. Filter Plate - (13”) FPX010013 / (18”) FPX010018
6. Filter - (2hp) FCS133995 / (2.5hp) FCS183900
5g. Internal Silencer - (2hp) BSC130000 /
(2.5hp) BSC180000
5b. J - Hooks (8) -AFJ051602 /AFT000001
5a. Plenum - FPX000001
4. Cyclone Cone - SCX002105 / SCX025105
1a. 2hp motor - BMZ020105 / 2.5hp - BMZ025105
1. MotorAssembly - (2hp) BXI002105 / (2.5hp) BXI002505
5e. Dust Bin - (13”) FPZ000013 / (18”) FPZ000018

2hp 50hz Super Gorilla Owner’s Manual © O.A.S. 2010
7
VI.AssemblyInstructions
Clips - AFT051618
Motor Plate
Gasket
Material
Gasket material goes
outside of clip holes
on top and bottom of
fan housing.
Gasket
Material
Collector
Barrel
Fan
Housing
Washer
Washer
Bolt
Bolt
Clip
Instructions for assembly of the Fan Blower Housing and Barrel of the Oneida Models.
1. Push clips onto inside circle on Fan Housing, making sure clip is pushed all of the way on, that the bolt
holes are in alignment with the clip holes and that the small barrel on the clip is on the INSIDE of the Fan
Housing as shown in diagram.
2. Stick the gasket material around the Fan Housing as shown in the diagrams, outside of the bolt circle.
Making sure of a complete seal. Dust collection systems cannot operate effectively without being tightly
sealed with no air leaks.
3. Put bolt through washer. then into appropriate bolt holes in Fan Housing and Barrel. Tighten bolts so
they all are snug, then go back and finish tightening the bolts in a star pattern.
Proportions and sizes of parts may be
exaggerated for purposes of explanation.
It is CRITICAL that this part
of the clip is put on the inside
of the Fan Blower Housing as
shown here. Otherwise you
will not get the seal needed for
complete dust collection!

8
2hp 50hz Super Gorilla Owner’s Manual © O.A.S. 2010
VI.GeneralAssemblyInstructions Do NOT use hook on motor to lift unit.
There are essentially three ways to assemble your collector and to at-
tach it to the stand. The way that is right for you should be determined
by expertise and manpower available. When the units are all assem-
bled they are very heavy and top weighted.All of this should be taken
into account before deciding on the method best suited for you.
With all assemblies, make sure rectangular air
outlet is oriented on Fan/Blower housing as
you are looking down as in Fig. 1Aor facing it
as shown in diagrams. This is very important.
Then you can rotate the housing to whatever bolt
position is best for your shop.
Before you start, make sure you have read the directions thoroughly.
Bolt Fan / Blower housing to Cyclone barrel, Then bolt Motor and
Plate to Fan/Blower housing. Carefully lay unit on its side and then
bolt cone to barrel. Lift entire unit up onto stand. Unit is extremely
heavy and top weighted, be advised!
Bolt Fan / Blower housing to Cyclone barrel, Then bolt Motor and
Plate to Fan/Blower housing. Put Cone up on stand and orient holes.
Lift assembled unit onto cone making sure proper holes are lined up.
Bolt unit to stand, then finish bolting barrel to cone.
Bolt Fan / Blower housing to Cyclone barrel, Put Cone up on stand
and orient holes. Lift assembled unit onto cone making sure proper
holes are lined up. Bolt unit to stand, then finish bolting barrel to
cone. Lift Motor & Plate onto Fan/Blower housing and bolt together in
proper direction.
Method #1 -
Method #2 -
Method #3 -
If you are having trouble getting your drum out
to empty it, you can cut down the flex hose to
give yourself more room. Just make sure that the
drum lid tightly seals to the drum and that there
are no leaks in the flex hose connection.

92hp 50hz Super Gorilla Owner’s Manual © O.A.S. 2010