ACTi PJSK-0102 User manual

PJSK-0102
User Manual
2022/11/23

www.acti.com
USER MANUAL
2
Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.

www.acti.com
USER MANUAL
3
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class Adigital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is
not installed and used in accordance with the instruction manual, it may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at
their own expense.
LVD/EMC Directive
This product complies with the European Low Voltage Directive 2014/35/EU
and EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical &
Electronic Equipment (WEEE) Directive and must be disposed of in a
responsible manner.
Battery Directive-2013/56/EC
Battery in the product complies with the European Battery Directive
2013/56/EC. For proper recycling, return the battery to your supplier or to a
designated collection point.

www.acti.com
USER MANUAL
4
Safety Instructions
The device must be installed, serviced, and maintained by a trained professional with necessary
safety knowledge and skills. Before you start using the device, please read through this guide
carefully and make sure all applicable requirements are met to avoid danger and loss of property.
Storage, Transportation, and Use
•Store or use the device in a proper environment that meets environmental requirements,
including and not limited to, temperature, humidity, dust, corrosive gases,
electromagnetic radiation, etc.
•Make sure the device is securely installed or placed on a flat surface to prevent falling.
•Unless otherwise specified, do not stack devices.
•Ensure good ventilation in the operating environment. Do not cover the vents on the
device.Allow adequate space for ventilation.
•Protect the device from liquid of any kind.
•Make sure the power supply provides a stable voltage that meets the power
requirements of the device. Make sure the power supply's output power exceeds the total
maximum power of all the connected devices.
•Verify that the device is properly installed before connecting it to power.
•Do not remove the seal from the device body without consulting the manufacturer first.
Do not attempt to service the productyourself. Contact a trained professional for
maintenance.
•Always disconnect the device from power before attempting to move the device.
•Take proper waterproof measures in accordance with requirements before using the
device outdoors.
Battery Use Caution
•When battery is used, avoid:
oHigh or low extreme temperature during use, storage, and transportation.
oExtremely low air pressure or low air pressure at high altitude.
oBattery replacement.
•Use the battery properly. Improper use of the battery such as the following may cause
risks of fire, explosion or leakage of flammable liquid or gas.
oReplace battery with an incorrect type.
oDispose of a battery into fire or a hot oven, or mechanically crushing or cutting of
a battery.
•Dispose the used battery according to your local regulations or the battery
manufacturer’s instructions.

www.acti.com
USER MANUAL
5
Power Requirements
•Installation and use of the device must be in strict accordance with your local electrical
safety regulations.
•Use a UL certified power supply that meets the requirements if an adapter is used.
•Use the recommended cord set (power cord) in accordance with the specified ratings.
•Only use the power adapter supplied with your device.
•Use a mains socket outlet with a protective earthing (grounding) connection.
•Ground your device properly if the device is intended to be grounded.

www.acti.com
USER MANUAL
6
Table of Contents
Precautions ................................................................... 2
Safety Instructions............................................................................................. 4
Introduction .................................................................. 8
Packing List........................................................................................................ 8
Photo Indication................................................................................................ 8
Joystick Function..........................................................................................................................11
Keyboard Interface.......................................................................................................................12
Cable Connection......................................................... 13
Connect RS-485 Connector............................................................................... 13
Startup and Shutdown................................................. 14
Startup............................................................................................................ 14
Shutdown........................................................................................................ 14
Setup........................................................................... 15
Set the Network .............................................................................................. 15
Add NVR Devices............................................................................................. 15
Manage Users ................................................................................................. 15
Common Operations.................................................... 16
Basic Concept.................................................................................................. 16
Control a PTZ Camera ...................................................................................... 16

www.acti.com
USER MANUAL
7
Option 1 .......................................................................................................................................16
Option 2 .......................................................................................................................................17
Play Live Video ................................................................................................ 17
Control Menus................................................................................................. 18
Multi-Window View ........................................................................................ 18

www.acti.com
USER MANUAL
8
Introduction
Packing List
1. Keyboard 3. Serial Port Cable
2. Feet (4 pcs.) 4. User Document
Photo Indication
The image below is for reference only, actual product may slightly differ.
Item
Description
1
Screen
LCD screen
2
Indicator
PWR (Power)
Steady blue for normal operation
NET (Network)
Steady blue for normal network connection
TX/RX (Data
Transmission)
Blinks blue when transmitting data
3
Playback Keys
Reserved.
Reserved.

www.acti.com
USER MANUAL
9
Item
Description
Reserved.
Reserved.
Reserved.
Reserved.
4
Knob
Reserved.
5
Function Keys
ESC
Cancel or exit.
LOCK
Lock.
SYS
Open the main menu.
SHIFT
Switch input method.
ID
Device ID.
SET
Set.
MON
Use with a number key toselect a monitor.
WIN
Use with a number key toselect a window on
screen.
CAM
Use with a number key toselect a camera.
PANEL
Reserved.
MULT
Use with a number key to set a multi-window view
on screen.
MON_G
Reserved.
CAM_G
Reserved.
GROUP
Reserved.
PRESET
Call or set preset.
PATROL
Call or set patrol.
ROUTE
Call or set route.
RUN/STOP
Reserved.
REC
Reserved.
PREV
Display the previous screen inNVR control mode
during sequence.
NEXT
Display the next screen in NVRcontrol mode
during sequence.
6
Number / Letter Keys / Clear / Enter
Input numbers or letters.Press SHIFT to switch.
7
PTZ Control
Keys
FOCUS+/MENU
Increase camera focus in PTZcontrol mode.
Open the main menu in NVRcontrol mode.
FOCUS-/R_CLICK
Decrease camera focus in PTZcontrol mode.

www.acti.com
USER MANUAL
10
Item
Description
In NVR control mode, show the shortcut menu that
appears with a right-click ofthe mouse.
IRIS+/MUTE
Increase camera iris in PTZcontrol mode.
Turn off audio in NVR controlmode.
IRIS-/TOOLBAR
Decrease camera iris in PTZcontrol mode.
Display toolbar in NVR controlmode.
ZOOM+/F1
Zoom in in PTZ control mode. Switch active area
(e.g., text box, drop-down list) on a tab in NVR
control mode (same asF1).
ZOOM-/F2
Zoom out in PTZ controlmode.
Switch tabs in NVR controlmode (same as F2).
LIGHT/PTZ
Turn on light in PTZ controlmode.
Display PTZ control window inNVR control mode.
WIPER/EDIT
Turn on wiper in PTZ controlmode.
Switch control mode in NVRcontrol mode.
Input numbers or letters inmenu mode.
8
Auxiliary keys (AUX1-AUX5)
For expansion.
9
Joystick
Control PTZ cameras. SeeJoystick Function for
details.
10
SWITCH
Press once: confirm.
Press twice: snapshot when controlling PTZ
camera or recording video.

www.acti.com
USER MANUAL
11
Joystick Function
Operation
Description
Up
•Navigate between menu items.
•Tilt up in PTZ control mode.
•Play fast or select the previous menu in NVR controlmode.
Down
•Navigate between menu items.
•Tilt down in PTZ control mode.
•Play slow or select the next menu in NVR control mode.
Left
•Navigate between menu items.
•Turn left in PTZ control mode.
Right
•Navigate between menu items.
•Turn right in PTZ control mode.
Upper left/lowerleft/upper
right/lower right
Control directions in PTZ control mode.
Rotate counterclockwise
Zoom out in PTZ control mode.
Rotate clockwise
Zoom in in PTZ control mode.
NOTE:
•In PTZ control mode, the further you tilt the joystick, the faster the camera rotates.
•The joystick allows the maximum rotation degree of ±45°.
•Use the joystick carefully to avoid damage.

www.acti.com
USER MANUAL
12
Keyboard Interface
Network Interface Keyboard
Serial-Interface Keyboard

www.acti.com
USER MANUAL
13
Cable Connection
Connect RS-485 Connector
1. Connect the network video recorder (NVR) through the RS-485 connector.
2. Connect Aof the RS-485 connector to RS-485+ of the NVR
3. Then connect B to the RS-485-of the NVR.
NOTE: Only 2A and 2B of the RS-485 connector can be used to connect keyboard in parallel.

www.acti.com
USER MANUAL
14
Startup and Shutdown
Startup
1. Connect power. The power LED is lit. When the system time displays on the screen,press
ENTER.
2. Use the joystick (tilt left/right/up/down) to navigate and input the correctusername and
password.
NOTE:
•The default admin username/password is admin/123456. The default operator
username/password is user/123456.
•Press SHIFT to switch inputs between numeric, uppercase letters, andlowercase
letters.
•When locked, the system time displays on the screen. To display the main menu,
press ENTER and input the username and password.
3. Press ENTER to display the main menu.
Shutdown
Exit the system and then unplug the power to completely shut down the keyboard.

www.acti.com
USER MANUAL
15
Setup
Press ENTER on the keyboard to access the main menu.
Set the Network
1. Tilt the joystick up/down to navigate. Press ENTER to select. Press ESC to exit.
Path: Main Menu>Local Cfg>Net Cfg
2. Use the joystick to locate the cursor. Press the number keys to input the IP, subnet, mask
and gateway.
NOTE: The default IP address is 192.168.1.16.
Add NVR Devices
Only an administrator can add devices.
Step 1: Preparation
•Log in to the NVR and note down its device ID (to be used in Step 2).
•Make sure the NVR to add is connected.
Step 2: Procedures
1. Tilt the joystick up/down to navigate. Press ENTER to select.
Path: Main Menu>Dev Manage>Manual Cfg>Add Dev
2. Set the device ID, name, type, and connection method.
NOTE: The device ID must be set correctly. See “Basic Concept”for details.
•If the keyboard is connected to the NVR through an RS-232 or RS-485 interface,
press ENTER and then complete the settings. The protocol, baud rate, data bit,
check bit, and stop bit should be the same as the settings in the NVR.
•If the keyboard is connected to the NVR through network, press ENTER and
then input the NVR's IP address.
Manage Users
1. Tilt the joystick up/down to navigate. Press ENTER to select.
Path: Main Menu>Advance Cfg>User Manage
2. Add and delete users as needed or change the user passwords.

www.acti.com
USER MANUAL
16
Common Operations
Press ENTER to access the main menu.
Basic Concept
ID refers to Device ID.
If the NVR is connected through the RS-485 serial interface, you need to input theNVR's actual
ID (you can find out by logging in to the NVR) and set the serial interface in the NVR as follows:
serial interface mode to keyboard, protocol to UV-1, baud rate to 9600, data bit to 8, stop bit to 1,
and check bit to none.
If the NVR is connected through the network, the preceding requirement on ID is unnecessary
because device IDs are only used for searching.
Control a PTZ Camera
Use the joystick or PTZ control ntrlooekeys to operate a PTZ connected.
Option 1
1. Input the ID.
2. Input the NVR’s device ID and then press ENTER. The basic device information is
displayed.
3. Press ENTER to confirm
4. Press a number key and then press MON to specify the monitor.
5. Press a number key and then press WIN to specify the preview window likned to the PTZ
camera.
NOTE:
•You need to log into the NVR first, otherwise PTZ control will be unavailable.
•PTZ control is unavailable if the specified window links to more than one camera.
6. Press PTZ to activate PTZ control mode.
•Use the PTZ control keys to adjust zoom and focus.

www.acti.com
USER MANUAL
17
•Use the joystick to control the rotation direction and speed (speed depends on
the degree of rotation). Twist the joystick to zoom in and out.
7. Press ESC to exit PTZ control mode.
Option 2
You need to log in to the NVR and note down the camera's device ID (to be usedin Step 4).
1. Press ID.
2. Input the NVR's device ID and then press ENTER. The basic device informationis
displayed.
3. Press ENTER to confirm.
4. Press a number key and then press CAM to specify the PTZ camera.
5. Press PTZ to activate the PTZ control mode.
•Use the PTZ control keys to adjust zoom and focus.
•Use the joystick to control the rotation direction and speed (speed dependson
the degree of rotation). Twist the joystick to zoom in and out.
6. Press ESC to exit PTZ control mode.
Play Live Video
Play live video on the screen with the current screen layout (e.g. 4 windows).
1. Press ID.
2. Input the NVR's device ID and then press ENTER. The basic device informationof is
displayed.
3. Press ENTER to confirm.
4. Press a number key and then press MON to specify the monitor.
5. Press a number key and then press WIN to specify the preview window.
6. Press a number key and then press CAM to specify the camera.
7. Press ENTER.

www.acti.com
USER MANUAL
18
Control Menus
1. Press ID.
2. Input the device ID and then press ENTER.
•R_CLICK: Show the shortcut menu that appears with a right-click of the mousein
a preview window.
•MENU: Display the main menu.
•ESC: Return to the previous window.
•MUTE: Turn off audio
•TOOLBAR: Show the toolbar
•F1: Switch active area such as text box, drop-down list on a tab.
•F2: Switch tab on screen
Multi-Window View
Change the preview layout (number of on-screen windows) on NVR.
1. Press ID.
2. Input the NVR device ID and then press ENTER.
3. Press MULTI until the desired multi-window view appears, or press a number key and
then press MULTI.

Copyright © 2014, ACTi Corporation All Rights Reserved
7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C.
TEL : [phone] FAX : [phone]
Email: [e-mail]