ACTi ACM-3701E User manual

Megapixel IP Dome
ACM-3401
Megapixel Day&Night IP Dome
ACM-3411
Ver. 080130
Quick Installation Guide
Megapixel IP Vandal Proof PoE Indoor Mini Dome
ACM-3701E
Ver. 120803
Quick Installation Guide
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

0-1
0Getting Started
1.1 PACKAGE CONTENTS
ACM-3701E Product CD
Warranty Card Drill Template
Mount Screws Allen/Hex Key
RJ45 Field Installable Feed
Through Adaptor
1
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

0-2
1.2 PHYSICAL DESCRIPTION
1. Ethernet Indicator LED
The LED will indicate ethernet speed and active states after IP
camera has connected completely.
2. Power LED
The LED will light up after IP camera has successfully completed
the boot process
3. Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button. Reconnect
the power cable while continuing to hold the reset button.
Step 3: Keep holding the reset button depressed around 16
seconds, release the reset button. The unit will start up with
factory default settings.
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

0-3
Model
ACM-3701E
Picture
Type
Rugged RJ-45 Connector
4. Ethernet Port
The IP device connects to the Ethernet via a female RJ-45
industrial connector.
The Ethernet port supporting Power over Ethernet.
Supporting NWAY, this IP device can auto detect the speed of
local network segment (10Base-T/100Base-TX Ethernet).
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

0-1
1.3 BASIC CONNECTIONS
Follow the procedures below to connect the IP device to the respective
apparatuses.
1. Connect this IP device’s ethernet port to an Ethernet (RJ45 connector). IP
device has only PoE built-in, you must regard it as a PD and connect it
directly to a PSE device like PoE switch.
2. Connect a PC to the Ethernet hub
NOTE: You may find a support package for help you getting familiar
with PoE. Please visit our web site, and get the support document
TS-00040.
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

1-2
1Quick Tour
This section guides you with a quick tour on this IP device.
2.1 Configure this IP Device
2.1.1 Make sure network environment
Default IP of this IP device is 192.168.0.100. Please make sure this IP device and
your PC are on the same network segment before running the installation.
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

1-3
2.1.2 Open Internal Explorer with IP address
NOTE: If your web browser is earlier than IE6, then download IE6 is
recommended.
NOTE: This IP device default IP address is set to 192.168.0.100
2.1.3 Login with default administrator’s account & password
NOTE: Default administrator account is set to Admin, password is set to
123456, and click button.
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

1-4
2.1.4 Preview the video
2.1.5 Set the new IP address
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]