ACTi ACM-1511 Series User manual

Megapixel IP IR DN PoE Bullet Camera
(with DC 12V / PoE)
ACM-1511 series
Ver. 120312
Quick Installation Guide

0-1
0Getting Started
1.1 PACKAGE CONTENTS
ACM-1511 series
(DC12V / PoE)
The bracket is not included
Product CD Terminal Block for Power
Warranty Card
1

0-2
1.2 PHYSICAL DESCRIPTION
1. Audio Input / Output
The Megapixel IP IR DN PoE Bullet Camera supports audio input
and output with earphone jack
2. Power Input
If your power input is DC12V , please follow the description on
the connector to connect to power.
3. Ethernet Port
The Megapixel IP IR DN PoE Bullet Camera connects to the
Ethernet via a standard RJ45 connector. Supporting NWAY, this
Megapixel IP IR DN PoE Bullet Camera can auto detect the speed
of local network segment (10Base-T/100Base-TX Ethernet).
4. Reset Button
Step 1: Switch off Megapixel IP IR DN PoE Bullet Camera by
disconnecting the power cable
Step 2: Press and continue to hold the Reset Button. Reconnect
PIN
NAME
DESCRIPTION
1
12V
DC Power Input
2
GND
Ground Pin

0-3
the power cable while continuing to hold the reset button.
Step 3: Keep holding the reset button depressed for a while,
release the reset button. The unit will start up with factory default
settings.
5. Power LED Indicator
The LED indicator lights up one time upon power up. It will
lights up again when this Megapixel IP IR DN PoE Bullet Camera
is fully booted up.

0-4
1.3 BASIC CONNECTIONS
Follow the procedures below to connect the Megapixel IP IR DN PoE
Bullet Camera to the respective apparatuses.
1. Connect the power adaptor to Megapixel IP IR DN PoE Bullet Camera
2. Connect Megapixel IP IR DN PoE Bullet Camera’s ethernet port to an
Ethernet (RJ45 connectors). If your Megapixel IP IR DN PoE Bullet
Camera has PoE built-in, you can regard it as a PD and connect it directly
to a PSE device like PoE switch.
3. Connect a PC to the Ethernet hub (RJ45 connectors)
1
NOTE: You may find a support package for help you getting familiar
with PoE. Please visit our web site, and get the support document
TS-00040.

0-5
1.4 Installation Procedure
1.4.1 Install the camera onto bracket
1.4.2 Rotate camera box counter-clockwise to remove camera
cover

0-6
1.4.3 Adjust the focus / zoom
- Zoom adjust lever
- Focus adjust lever

1-7
1Quick Tour
This section guides you with a quick tour on this Megapixel IP IR DN PoE Bullet
Camera.
2.1 Configure this Megapixel IP IR DN PoE Bullet Camera
2.1.1 Make sure network environment
Default IP of this Megapixel IP IR DN PoE Bullet Camera is 192.168.0.100. Please
make sure this Megapixel IP IR DN PoE Bullet Camera and your PC are on the same
network segment before running the installation.
2.1.2 Open Internal Explorer with IP address
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)

1-8
NOTE: If your web browser is earlier than IE6, then download IE6 is
recommended.
NOTE: This Megapixel IP IR DN PoE Bullet Camera default IP address is
set to 192.168.0.100
2.1.3 Login with default administrator’s account & password
NOTE: Default administrator account is set to Admin, password is set to
123456, and click button.
2.1.4 Preview the video

1-9
2.1.5 Set the new IP address

1-10
*IP Address : The default IP address is 192.168.0.100.
*Subnet Mask : The default subnet mask is 255.255.255.0
*Click button
NOTE: In your Client PC, please make sure the setting of Network
Connections Type is set to Auto Negotation, since this Megapixel IP IR
DN PoE Bullet Camera follows MII standard. Otherwise, you might not
see the live image.
IMPORTANT: After the IP address is changed, please record this IP
address. There’s no way to connect to the Megapixel IP IR DN PoE Bullet
Camera if user forgets the new IP address.
2.1.6 Check Default Video Setting

1-11
2.1.7 Click Save Reboot to restore all settings and please wait about 30 seconds
for system reboot.