ACTi E44 User manual

Bullet Camera
Hardware Manual
E44, E45, E46
Ver. 2013/06/05

www.acti.com
Hardware Manual
2
Table of Contents
Precautions 3
Safety Instructions ...........................................................................5
Introduction 6
List of Models....................................................................................6
Package Contents.............................................................................7
Physical Description ........................................................................8
Installation Procedure 9
Mount the Camera ............................................................................9
Waterproof Cable Installation........................................................ 11
Basic Waterproof..........................................................................12
Full Waterproof.............................................................................15
Basic Connections .........................................................................21
Connecting a Single Camera.......................................................21
Connecting Multiple Cameras......................................................22
Adjust Focal Length and Focus ....................................................23
Accessing the Camera 24
Configure the IP Addresses...........................................................24
Using DHCP Server to Assign IPAddresses................................24
Using the Default Camera IPAddress..........................................26
Access the Camera.........................................................................28

www.acti.com
Hardware Manual
3
Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to
follow the safety instruction given may directly endanger people, cause damage to the system
or to other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.

www.acti.com
Hardware Manual
4
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for compliance could void the user’s authority to operate the equipment.
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to European Standard EN 55022
and EN 55024. In a domestic environment, this product may cause radio interference in which
cause the user may be required to take adequate measures.

www.acti.com
Hardware Manual
5
Safety Instructions
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to
qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in
this manual. Adjust only those controls that are covered by the instruction manual, as an
improper adjustment of other controls may result in damage, and will often require
extensive work by a qualified technician to restore the video product to its normal
operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.

www.acti.com
Hardware Manual
6
Introduction
List of Models
This hardware manual contains the following models:
E44
2MP Bullet with D/N, IR, Basic WDR, SLLS, Vari-focal lens
E45
1MP Bullet with D/N, IR, Superior WDR, Vari-focal lens
E46
3MP Bullet with D/N, IR, Superior WDR, Vari-focal lens

www.acti.com
Hardware Manual
7
Package Contents
Bullet Camera
Sunshield
Mounting Screw Kit
Sunshield Screw Kit
Waterproof Kit
Drill Template
Quick Installation Guide
Warranty Card

www.acti.com
Hardware Manual
8
Physical Description
Side View
Back View
1) Ethernet Connector
Connects to the network and power source. See Basic Connections on page 21 for more
instructions.

www.acti.com
Hardware Manual
9
Installation Procedure
Mount the Camera
1. Attach the bracket to the camera.
2. Mark the location of the screw holes based on the drill template included in the package.
NOTE: Depending on the surface where you will install the camera, it may be necessary to
drill three (3) holes and use the supplied screw tox.
3. Attach the camera to the surface using the three (3) supplied screws.
4. When installing the camera outdoors, attach the sunshield using the supplied screws and
washers.
5. Adjust the camera installation angle and orientation, and then tighten the two (2) screws to
fix its position.

www.acti.com
Hardware Manual
10
6. Connect the RJ-45 male-type connector of the camera to the 2-sided female type
connector (included in the waterproof cable kit). On the other side of the 2-sided female
type connector, connect the Ethernet cable from the network.
The above cable connection can be used if the camera will be installed indoors or when a
junction box will be used on an outdoor installation.
If the camera will be installed outdoors and without a junction box to protect the cable
connection from rain or dust, be sure to apply the waterproof installation, see Waterproof
Cable Installation on page 11.
Ethernet cable
of the camera
Ethernet cable
from the network
2-Sided Female Type
Connector

www.acti.com
Hardware Manual
11
Waterproof Cable Installation
There are two ways to waterproof the cable installation:
Basic Waterproof: Waterproof cable connection with naked cable.
Full Waterproof: Waterproof cable connection with watertight flex conduit.
The Waterproof Cable Kit that came with the camera contains the following items:
The 2-Sided Female Type Connector is used in all types of cable connection.
Basic Waterproof
Accessories
Full Waterproof
Accessories
2-Sided Female Type
Connector

www.acti.com
Hardware Manual
12
Basic Waterproof
1. Prepare the basic waterproof cable accessories. Detach the parts as follows:
NOTE: The above accessories come in two sets, one for the Ethernet cable of the camera
and the other for the network.
2. Insert the clamping nut through the Ethernet cable of the camera.
3. Insert the rubber seal.
Main Body
Rubber Seal
Clamping Nut

www.acti.com
Hardware Manual
13
4. Insert the main body.
5. Do the same procedures on the Ethernet cable on the network side.
6. Connect the Ethernet connector of the camera and the network to each side of the 2-sided
female type connector.
Ethernet cable
of the camera
Ethernet cable
from the network
2-Sided Female
Type Connector
Network Side
Camera Side

www.acti.com
Hardware Manual
14
7. On the Ethernet cable on the camera side, attach the rubber seal to the main body.
8. Attach the main body to the 2-sided female type connector.
9. Attach the clamping nut to the main body.

www.acti.com
Hardware Manual
15
10. Do the same procedures on the network cable side. Below is a complete cable connection.
Full Waterproof
1. Prepare the full waterproof cable accessories (included in the waterproof cable kit) and
flexible conduit cable (not included), with ½” diameter.
2. Detach the parts of the main body, as follows:
NOTE: The Lock Nut is designed for use with junction boxes and will not be used in this
installation. Please set it aside.
Clamping Nut
Sealing Insert
Body
Lock Nut
2-Sided Female
Type Connector
Converter
Washer
Main Body

www.acti.com
Hardware Manual
16
3. Insert the clamping nut through the Ethernet cable of the camera.
4. Insert the rubber seal.
5. Insert the main body.

www.acti.com
Hardware Manual
17
6. Connect the Ethernet cable of the camera to the shorter end of the 2-sided female type
connector, and then set the cable aside.
7. On the network side, insert the Ethernet cable through the flex conduit.
8. Insert the clamping nut through the flex conduit.
Thicker-end for
network
Shorter-end for
network

www.acti.com
Hardware Manual
18
9. Insert the sealing insert and attach it at the end of the flex conduit.
10. Insert the body through the Ethernet cable and attach the body to the clamping nut.
11. Insert the converter and attach it to the body.

www.acti.com
Hardware Manual
19
12. Insert the washer into the thicker side of the 2-sided female type connector.
13. Attach the network side converter to the 2-sided female type connector.
14. On the Ethernet cable on the camera side, attach the rubber seal to the main body.

www.acti.com
Hardware Manual
20
15. Attach the main body to the 2-sided female type connector.
16. Attach the clamping nut to the main body.
The waterproof cable connection is complete.