ACTi ACM-7411 Series User manual

MegaPixel IP Outdoor Rugged Dome
(with DC 12V / PoE)
ACM-7411 series
Ver. 080415
Quick Installation Guide
All manuals and user guides at all-guides.com
all-guides.com

0-1
0Getting Started
1.1 PACKAGE CONTENTS
ACM-7411 series Power Adaptor (Option)
(DC12V / PoE )
Product CD Terminal Blocks for Power, DI/O & Audio
Warranty Card Accessory
1
All manuals and user guides at all-guides.com

0-2
1.2 PHYSICAL DESCRIPTION
All manuals and user guides at all-guides.com

0-3
1. Ethernet Port
The IP device connects to the Ethernet via a standard RJ45
connector. Supporting NWAY, this IP device can auto detect the
speed of local network segment (10Base-T/100Base-TX
Ethernet).
2. Power Input
If your power input is DC12V. Please follow the description on the
connector to connect to power.
3. Power Input Audio & DIO input/output
PIN NAME DESCRIPTION
1 12V DC Power Input
2 GND Ground Pin
PIN NAME DESCRIPTION
1 DIO PW DC12VIN
2 DIO GND DGND
3 DO
DO1_TO_OUTSIDE
4 DI
DI1_FROM_OUTSIDE
5 AO_GND DGND
6 A_OUT
Audio_OUT_LR
7 AI_GND DGND
8 A_IN
Audio_IN
All manuals and user guides at all-guides.com

0-4
4. Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button. Reconnect the
power cable while continuing to hold the reset button.
Step 3: Keep holding the reset button depressed around 6 seconds,
release the reset button. The unit will start up with factory default
settings.
5. Conduit Hole
These conduit holes are used for cables to go through.
1.3 INSTALLATION PROCEDURE
There are three types of installation of this IP outdoor rugged dome series.
Surface mount Flush mount Wall mount
Pictures
Optional Bracket
required
●●
The mounting procedure can be divided into two parts,
1st: Connect the IP outdoor rugged dome series
2nd: Mount the IP outdoor rugged dome series
All manuals and user guides at all-guides.com

0-5
1.3.1 Connect the IP Outdoor Rugged Dome
1.3.1.1 Remove the cover
Remove the dome cover with special hex wrench in the accessory bag.
1.3.1.2 Insert the cabl
There are two conduit holes, one is at the dome bottom and the other one is
at the side of rugged dome with plug. Remove the plug if your cable will go
through the one at the side of rugged dome
All manuals and user guides at all-guides.com
all-guides.com

0-6
1.3.1.3 Connect cables to connectors
Please follow the instruction at Chapter 2: Physical Description, for how to
connect to each connector.
1.3.1.4 LED Description
There are three LEDs in the system. They are indicators for power, fan and
heater respectively. According to operating temperature, the different LED
will be lighted for different situation.
All manuals and user guides at all-guides.com

0-7
1.4 Mount the IP Outdoor Fixed Dome (Surface)
All manuals and user guides at all-guides.com

0-8
1.5 Mount the IP Outdoor Fixed Dome (Flush)
All manuals and user guides at all-guides.com

0-9
1.6 Mount the IP Indoor Fixed Dome (Wall)
All manuals and user guides at all-guides.com

0-10
Adjust the camera
2.1 Adjust zoom and focus
Please adjust the camera direction first. Then move the focus and the zoom
lever at the picture 1 to adjust the zoom and the focus. Fix the zoom and
focus after adjusting.
2.2 Adjust camera functions
Refer to picture 1 for what can be adjusted and how to adjust.
Picture1
1. focus lever
2. Zoom lever
3. Tilt adjustment screw
4. Image adjustment axis
5. Pan adjustment screw
2
All manuals and user guides at all-guides.com
all-guides.com

0-11
QuickTour
This section guides you with a quick tour on this IP device.
3.1 Configure this IP Device
3.1.1 Make sure network environment
Default IP of this IP device is 192.168.0.100. Please make sure this IP device and
your PC are on the same network segment before running the installation.
3.1.2 Open Internal Explorer with IP address
3
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)
All manuals and user guides at all-guides.com

0-12
NOTE: If your web browser is earlier than IE6, then download IE6 is
recommended.
NOTE: This IP device default IP address is set to 192.168.0.100
3.1.3 Login with default administrator’s account & password
NOTE: Default administrator account is set to Admin, password is set to
123456, and click button.
3.1.4 Preview the video
All manuals and user guides at all-guides.com

0-13
3.1.5 Set the new IP address
*IP Address : The default IP address is 192.168.0.100.
*Subnet Mask : The default subnet mask is 255.255.255.0
*Click button
NOTE: In your Client PC, please make sure the setting of Network
Connections Type is set to Auto Negotation, since this IP device follows
MII standard. Otherwise, you might not see the live image.
IMPORTANT: After the IP address is changed, please record this IP
address. There’s no way to connect to the IP device if user forgets the
new IP address.
All manuals and user guides at all-guides.com

0-14
3.1.6 Check Default Video Setting
3.1.7 Click Save Reboot to restore all settings and please wait about 30 seconds
for system reboot.
All manuals and user guides at all-guides.com