ActionTec GT704-WG User manual

54 Mbps
Wireless
DSL Gateway
Model #: GT704WG
User Manual
Version 2.0
Solutions for the Digital Life™

Table of Contents
1 Introduction 1
Package Contents 1
Minimum System Requirements 2
Features 2
Getting to Know the Gateway 3
2 Performing a Quick Setup 7
Accessing Quick Setup Screens 7
Changing the Password 11
3 Viewing the Gateway’s Status 13
Broadband Connection Status 13
Network Status 16
4 Configuring Wireless Settings 17
Accessing Wireless Setup 17
Basic Wireless Setup 21
Wireless Advanced Settings 21
Connection 1-2-3 26
Wireless Status 27
5 Configuring Advanced Settings 29
Accessing Advanced Setup Screens 29
DSL Settings 33
DHCP Server 33
LAN IP Address 35
WAN IP Address 36
QoS Settings Upstream 38
QoS Settings Downstream 41
QoS Status 42
Remote Management/Telnet 42
Telnet Timeout Setting 43
Dynamic Routing 44
Static Routing 44
UPnP (Universal Plug and Play) 45
USB Port Detection 45
Time Zone 46
Remote Syslog Capture 46
i

ii
Actiontec 54 Mbps Wireless DSL Gateway User Manual
iii
Table of Contents
ii
6 Configuring Security Settings 47
Accessing Wired Security Screens 47
Admin User Name and Password 50
Firewall 50
Applications 53
DMZ Hosting 55
NAT (Network Address Translation) 56
7 Configuring Parental Controls 57
Accessing Parental Control Screens 57
Services Blocking 60
Website Blocking 61
Schedule Rules 61
8 Configuring the Gateway’s Utilities 65
Accessing the Utilities Screens 65
Restore Default Settings 68
Upgrade Firmware 68
Multiple PVC 69
Web Activity Log 69
System Log 70
OAM Ping Test 71
Ping Test 71
Reboot 72
9 Troubleshooting 73
Troubleshooting 73
Frequently Asked Questions 75
A Reference 81
Locating Computer Information 81
Locating Windows Operating System Files 82
B Switching to Static IP on the Computer 85
Windows 98 SE 85
Windows Me 88
Windows 2000 91
Windows XP 95
C Computer Security 99
Comparing DSL Service with a Dial-Up Modem 99
Gateway Security 100
Computer Security 100
Electronic Security 101

ii
Actiontec 54 Mbps Wireless DSL Gateway User Manual
iii
Table of Contents
D Specifications 103
General 103
Wireless Operating Range 104
LED Indicators 104
Environmental 104
E Glossary 105
F Service Acronyms 109
Service Acronym Definitions 109
Notices 113
Regulatory Compliance Notices 113
Modifications 113
Limited Warranty 115

iv
Actiontec 54 Mbps Wireless DSL Gateway User Manual
This page left intentionally blank.

1
Introduction
Thank you for purchasing the Actiontec 54 Mbps Wireless DSL Gateway. The
Gateway is the simplest way to connect computers to a high-speed broadband
connection. This easy-to-use product is perfect for the home office or small busi-
ness. If you want to take your computing to the next level, the Actiontec 54 Mbps
Wireless DSL Gateway is sure to be one of the keys to your success.
Package Contents
s Actiontec 54 Mbps Wireless DSL Gateway
s Power cord
s DSL cable
s Yellow (Ethernet) cable
s Blue (USB) cable
s Quick start guide
1

2
Actiontec 54 Mbps Wireless DSL Gateway User Manual
3
Chapter 1 Introduction
Minimum System Requirements
s Active DSL service
s Computer with an 10 Mbps or 10/100 Mbps Ethernet connection, or USB
connection
s Microsoft Windows 98 Second Edition (SE), Windows Millennium Edition
(Me), Windows NT 4.0, Windows 2000, Windows XP, Mac OS 7.1+, Mac OS
8.0+, Mac OS 9.0+, or Mac OS X+
☞ Note: USB LAN port is not supported with Microsoft
Windows NT 4.0 or Mac OS.
s Internet Explorer 4.0 or higher (5.x recommended) or Netscape Navigator
4.0 or higher (4.7 recommended)
s TCP/IP network protocol installed on each computer
Features
s Plug-and-Play installation support for computers running Windows oper-
ating systems (98SE, Me, 2000 and XP)
s ADSL WAN port (RJ-11)
s Full-rate ANSI T1.413 Issue 2, ITU G.992.1(G.dmt) and G.992.2(G.lite)
standard compliance
s Auto-handshake for different ADSL flavors
s USB 1.1 device specification compliance
s 12 Mbps USB data rate (full speed) support
s Bridged Ethernet over ATM, PPP over ATM, PPP over Ethernet
s Precise ATM traffic shaping
s IP packet routing and transparent bridge
s RIP-1, RIP-2, and static routing protocol support
s Built-in NAT, DHCP server
s DNS relay support

2
Actiontec 54 Mbps Wireless DSL Gateway User Manual
3
Chapter 1 Introduction
s PAP/CHAP authentication, administrative passwords through Telnet
s 64-, 128-, and 256-bit WEP/WPA wireless LAN security
s IEEE 802.3 Ethernet standard compliance
s 10/100 Base-T Ethernet ports (4)
s Fast Ethernet flow control support
s Web-based configuration setup
s FTP firmware upgradeable
s Web download support
s 802.11b/g support
Getting to Know the Gateway
This section contains a quick description of the Gateway’s lights, ports, etc.
The Gateway has several indicator lights (LEDs) on its front panel and a series of
ports on its rear panel.
Front Panel
The front panel of the Gateway features nine lights: Power, DSL, Internet,
Ethernet (4), USB, and Wireless.
Power
DSL Internet
Ethernet
1Wireless
234USB
1234

4
Actiontec 54 Mbps Wireless DSL Gateway User Manual
5
Chapter 1 Introduction
Power Light
The Power light displays the Gateway’s current status. If the Power light glows
steadily green, the Gateway is receiving power and fully operational. When the
Power light is rapidly flashing, the Gateway is initializing. If the Power light is
glows red when the Power cord is plugged in, the Gateway has suffered a critical
error and technical support should be contacted.
DSL Light
The DSL light illuminates when the Gateway is connected to a DSL line.
Internet Light
When the Internet light glows steadily, the Gateway is connected to the DSL
provider. When it flashes, the Gateway’s built-in DSL modem is training for the
DSL service.
Ethernet Lights
The Ethernet lights illuminate when the Gateway is connected to one or more of
its yellow Ethernet ports.
USB Light
The USB light illuminates when the Gateway is connected via its USB port.
Wireless Light
The Wireless light illuminates when the Gateway is connected wirelessly (if the
Gateway’s Wireless feature is turned on).

4
Actiontec 54 Mbps Wireless DSL Gateway User Manual
5
Chapter 1 Introduction
Rear Panel
The rear panel of the Gateway contains seven ports (Ethernet [4], Phone, USB, and
Power), as well as Reset and Power switches.
12VDC 0.6A
421
ON/OFF
Ethernet Cable
(from Ethernet port [1-4]
to computer)
USB Cable
(from USB port
to computer)
Power Adapter
(from Power port
to power outlet)
DSL Cable
(from DSL port
to phone jack)
Ethernet Ports
The Ethernet ports are used to connect computers to the Gateway via Ethernet
cable. The Ethernet ports are 10/100 Mbps auto-sensing ports, and either a
straight-through or crossover Ethernet cable can be used when connecting to the
ports.
DSL Port
The DSL port is used to connect the Gateway to a DSL (Digital Subcriber Line)
connection.
Reset Switch
Depressing the Reset switch for one second will restore the Gateway’s factory
default settings. To reset the Gateway, depress and hold the Reset switch for
approximately one second. The reset process will start after releasing the switch.
USB Port
The USB port is used to connect a computer to the Gateway via USB cable.

6
Actiontec 54 Mbps Wireless DSL Gateway User Manual
Power Port
The Power port is used to connect the Power cord to the Gateway.
N Warning: Do not unplug the Power cord from the Gateway
during the reset process. Doing so may result in permanent
damage to the Gateway.
Power Switch
The Power switch is used to power the Gateway on and off.

7
Performing a
Quick Setup
This chapter is a guide through a quick set up of the Gateway, including how to
connect the Gateway to the ISP.
To complete the quick setup, have the Welcome Letter or ISP Worksheet handy. If
the document is not available, contact the ISP immediately.
Accessing Quick Setup Screens
To access the Quick Setup screens:
1. Open a Web browser. In the “Address” text box, type:
http://192.168.1.1
then press Enter on the keyboard.
2

8
Actiontec 54 Mbps Wireless DSL Gateway User Manual
9
Chapter 2 Performing a Quick Setup
2. The “Home” screen appears. Click Quick Setup.

8
Actiontec 54 Mbps Wireless DSL Gateway User Manual
9
Chapter 2 Performing a Quick Setup
3. A login window appears. Enter the user name and password in the appropri-
ate text boxes, then click OK.
☞ Note: The default user name is “admin.” The default password is
“password.”
4. Follow the instructions in the “Welcome to the Quick Setup” screen, then click Next.
5. At the top of the next window, select PPPoE or DHCP.
5a. If PPPoE was selected in step 5, the default user name and password are
entered in the appropriate text boxes.
If “DHCP” was selected, go to step 6.

10
Actiontec 54 Mbps Wireless DSL Gateway User Manual
11
Chapter 2 Performing a Quick Setup
5b. If PPPoE was selected in step 5, select the IP type (“Dynamic IP-DHCP
[Default]” or “Single Static IP Address”). If Single Static IP Address was select-
ed, enter the address in the appropriate text box.
6. Optional - Select the DNS type (“Dynamic DNS Addresses [Default]” or
“Static DNS Addresses”). If Static DNS Addresses was selected, enter the pri-
mary and secondary DNS addresses in the appropriate text boxes. If unsure
what to enter in this section, contact the ISP.
7. Click Apply at the bottom of the screen.
8. Read the instructions on the next screen. The Gateway is successfully
configured.
The Power light flashes rapidly while the Gateway restarts, then glows steadily
green when fully operational. The Internet light will also glow steadily green. The
Gateway is now configured and users can start surfing the Internet.
If an error appears, stating the Web browser was unable to connect to the Internet,
check the configuration settings. Ensure all the information required by the ISP is
entered correctly.

10
Actiontec 54 Mbps Wireless DSL Gateway User Manual
11
Chapter 2 Performing a Quick Setup
Changing the Password
To create or change the password allowing access to the Gateway’s Web
Configuration screens, follow these instructions:
1. From the “Home” screen, select Security.
2. The “Security” screen appears. Select “Admin User Name and Password.”
3. The “Change Admin Username/Password” screen appears. Enter a new
Username in the “Admin User Name” text boxt, then enter a new password in
the “Admin Password” text box. Make sure to write down the user name and
password and keep it in a secure location. They will be needed to access the
Gateway’s Web Configuration screens in the future.
4. Click Apply at the bottom of the screen.
5. Read the instructions on the next screen. The user name and password are
successfully changed.
Once the Gateway has rebooted, the new user name and password are active. To
access the Gateway’s Web Configuration screens, the new user name and password
must be entered.

12
Actiontec 54 Mbps Wireless DSL Gateway User Manual
This page left intentionally blank.

13
Viewing the
Gateway’s Status
After configuring the Gateway, the Gateway’s connection and network status can
be viewed. The Internet connection status is viewed in the “Broadband Connection
Status” screen, while the network status is viewed in the “My Network” screen.
Broadband Connection Status
To view the Gateway’s connection statistics, select Status in the Home screen. The
“Broadband Connection Status” screen appears. There are three sections in this
screen: General Statistics, PPP Status, and DSL Status.
☞
Note: No settings (other than connecting or disconnecting from
the Internet by clicking on Connect or Disconnect) can be
changed from the Broadband Connection Status screen.
General Statistics
The top section of the Broadband Connection Status screen displays general statis-
tics regarding the Gateway, including model number, firmware version, IP address,
and gateway IP address.
3

14
Actiontec 54 Mbps Wireless DSL Gateway User Manual
15
Chapter 3 Viewing the Gateway’s Status
PPP Status
The middle section of the Broadband Connection Status screen displays the status
of the Gateway’s PPP connection, including user name, authentication failures,
and packets sent and received.
DSL Status
The bottom section of the Broadband Connection Status screen displays the status
of the Gateway’s DSL connection, including mode settings, connection status, and
number of discarded packets. Click Reset to refresh all statistics on this screen

14
Actiontec 54 Mbps Wireless DSL Gateway User Manual
15
Chapter 3 Viewing the Gateway’s Status
In the menu on the left side of the Broadband Connection Status screen, there are
two other options available to view: NAT Table and Routing Table. Click to gen-
erate the option of choice.
NAT Table
Selecting NAT Table generates the “NAT Table” screen. This screen displays an overview
of the current list of open connections through NAT (Network Address Translation) the
Gateway supports between the networked computers and the Internet.
ARP Table
Selecting ARP Table generates the “ARP Table” screen. This screen displays the an
overview of the Gateway’s network routes.