Planet VIP-110 Installation manual

InternetTelephonyGateway
VIP-110/VIP-210
Command Reference
Release1.00
January 2004

2
COMMANDLINE CONFIGURATION
Command lineinterfacein PLANET VIP-110/VIP-210
This manual is acommand-by-command description for the PLANET VIP-110/VIP-210 CLI
administration mode.

i
Table of Contents
About This Manual 7
Document Objectives...........................................7
Audience......................................................7
Document Organization.........................................7
Notation Conventions..........................................7
Designating IP Address........................................8
Designating Port ID...........................................8
Documentation Abbreviations...................................8
1. Introduction 1
Command Help..................................................1
2. Utility Commands 3
get...........................................................3
help..........................................................3
reset.........................................................3
ping..........................................................3
tel erase_ivr.................................................4
tel set ring_freq.............................................4
tel show port.................................................4
tel show ring_freq............................................4
show version..................................................5
3. IP Configuration Commands 7
Configuring LAN Interface.....................................7
net set lan ip..............................................7
net set lan mask............................................7
net show lan................................................8
Configuring WAN Interface.....................................8

ii
net set wan dns.............................................8
net set wan gateway.........................................8
net set wan ip..............................................9
net set wan ip_tos..........................................9
net set wan mask............................................9
net show wan...............................................10
Configuring DHCP Server and Client...........................10
net set dhcp client........................................10
net set dhcp mac_addr......................................10
net set dhcp server........................................11
Configuring TFTP Server......................................11
net set tftpsrv............................................11
Configuring PPPoE............................................12
net set pppoe auth_proto...................................12
net set pppoe fixed_ip.....................................12
net set pppoe idle_timeout.................................12
net set pppoe {on | off}...................................13
net set pppoe service_name.................................13
net set pppoe tx_bw........................................13
net set pppoe user.........................................13
net show ppp...............................................14
Configuring Dynamic DNS......................................14
net set ddns {on | off}....................................14
net set ddns add...........................................15
net set ddns del...........................................15
net show ddns..............................................15
Configuring Management Options...............................16
net set http...............................................16
net set manager ip.........................................16
net set manager mask.......................................16
net set manager password...................................17
net set telnet.............................................17

iii
net show management........................................17
Storing IP Interface Parameters..............................18
net store..................................................18
4. Telephony Interface Port Configuration Commands 19
Configuring Port-Unique Parameters...........................19
set port port# cid name....................................19
set port port# cid number..................................19
set port port# default.....................................20
set port port# dial_in plar................................20
set port port# port_cfg....................................20
show port port# ............................................21
Configuring Port-Common Parameters...........................21
Configuration General Port-Common Parameters.................21
set port_cfg ans_wait......................................21
set port_cfg call_limit....................................22
set port_cfg default.......................................22
set port_cfg fax_prof......................................22
set port_cfg out_type......................................22
set port_cfg out_wait......................................23
set port_cfg rxgain........................................23
set port_cfg tone_out_off..................................23
set port_cfg tone_out_on...................................23
set port_cfg tone_out_pwr..................................24
set port_cfg txgain........................................24
set port_cfg voice_prof....................................24
show port_cfg..............................................25
FXS Signaling Configuration Commands.........................25
set port_cfg fxs answ_clear_detect.........................25
set port_cfg fxs caller_id.................................25
set port_cfg fxs cpc_dur...................................26
set port_cfg fxs cpc_wait..................................26

iv
set port_cfg fxs ff_batt_rev...............................26
set port_cfg fxs offhook_db................................27
set port_cfg fxs offhook_detect............................27
set port_cfg fxs onhook_db.................................27
set port_cfg fxs onhook_detect.............................28
set port_cfg fxs ring_id...................................28
5. Voice and Fax Coder Configuration Commands 31
Common Coding Profile Configuration Commands.................31
set coding default...........................................31
show coding profile_id .....................................31
Voice Coding Profile Configuration Commands..................31
set coding profile_id dtmf_relay.............................32
set coding profile_id sampling_time..........................32
set coding profile_id vad....................................33
Fax Coding Profile Configuration Commands....................33
set coding profile_id fax_hs_pkt_rate......................33
set coding profile_id fax_hs_redundancy....................33
set coding profile_id fax_ls_redundancy....................34
7. H323 Configuration Commands 35
General H.323 Configuration Commands.........................35
set h323 alt_dtmf..........................................35
set h323 call_name.........................................35
set h323 callSignalPort....................................36
set h323 cisco_t38.........................................36
set h323 default...........................................36
set h323 default_dtmf......................................36
set h323 display_name......................................37
set h323 dtmf_duration.....................................37
set h323 gk_mode...........................................37
set h323 h245_term_type....................................38

v
set h323 h245_timeout......................................38
set h323 h245_tunneling....................................38
set h323 in_fast_start.....................................39
set h323 local_alert.......................................39
set h323 nat_call..........................................39
set h323 out_fast_start....................................40
set h323 rtp_port_base.....................................40
set h323 term_id...........................................40
show h323..................................................41
H.323 Gatekeeper Related Configuration Commands..............41
set h323 alias.............................................41
set h323 allow_calls_wo_gk.................................41
set h323 alt_gk............................................42
set h323 alt_gk_name.......................................42
set h323 endpoint_prefix...................................43
set h323 endpoint_reg_type.................................43
set h323 gk_addr...........................................43
set h323 gk_id.............................................44
set h323 gk_max_tries......................................44
set h323 gk_name...........................................44
set h323 time_to_live......................................45
8. Configuration Management Command 47
config.......................................................47
9. Dial Plan Management Commands 49
Database Update Control Commands.............................49
atpm done..................................................49
atpm erase.................................................49
atpm purge.................................................49
atpm req...................................................50
atpm restore...............................................50
atpm store.................................................51

vi
Destination Table Management Commands........................51
atpm dadd..................................................51
atpm ddel..................................................52
atpm dfind.................................................52
atpm dlist.................................................52
Hunt Group Table Management Commands.........................53
atpm hadd..................................................53
atpm hdel..................................................53
atpm hfind.................................................53
atpm hlist.................................................54
Address Table Management Commands............................54
atpm aadd..................................................54
atpm adel..................................................55
atpm afind.................................................55
atpm alist.................................................55
Dialing Control Commands.....................................56
atpm slist.................................................56
atpm sys...................................................56
Index 59

Introduction 7
About This Manual
This section discusses the objectives, audience, organization, and conventions
associated with this document.
Document Objectives
This document provides anin-depthdescriptionof the commands necessaryfor configuring
and maintaining the ITG.
Audience
This publicationis intended asastandalone document for experienced systemadministrators
or engineerswho will be configuring and maintainingthe ITGand would liketo reference
commands.
Document Organization
This documentis organized as follows:
• Introduction, gives an overview about this document.
• Utility Commands describes general-purposeutilitycommands.
• IPConfigurationCommands describescommands for configuringthe network interfaces
anddisplaying the configuration.
• TelephonyInterface Port Configuration Commands describe commands forconfiguring
the telephonyinterface ports.
• Voice andFaxCoder ConfigurationCommands,describe commandsfor configuring the
voice and fax coders supported by the ITG.
• Call Progress ToneConfigurationCommands describe commandsforconfiguring thecall
progress detector and generator.
• H323 Configuration Commands describecommandsfor configuring the H.323 callcontrol
andsignaling protocolstack.
• Configuration Management Commands describe the command for managingthe
configuration parameters.
• Dial Plan ManagementCommands describecommandsfor setting up and viewing thedial
plan.
Notation Conventions
This documentuses the following conventions:
• Examples that contain system prompts denoteinteractivesessions, indicating that the
user enters commands at the prompt.
• Differenttype styles and characters are used. These serveavariety of purposesas
described below:

8
Convention Description
boldface Commandsand keywords are in boldface.
Bold Courier User input (anythingyouare expected totype in)isset in Bold Courier.
italic Arguments forwhichyou supplyvalues.
courier Messages that theITGCLI displaysare inplain courierfont.
[] Elements in square brackets areoptional.
{ x | y | z } Alternative but required elements are groupedin braces ({})andseparated by
verticalbars (|).
[ x | y | z ] Optionalalternativekeywords are grouped inbrackets([ ])andseparated by
verticalbars (|).
string”Anon-quotedset of characters. Do not usequotationmarks aroundthestring
orthe string willincludethe quotation marks.
<key> Akeyon theVT-100terminal or terminal emulator. For example <Enter>
denotes the Enterkey.
Designating IP Address
Some commands requirean IPaddress, which mustbe designated in astandardformat. The
IP address format is 32 bits,writtenas four octetsseparatedbyperiods (dotteddecimal
format) that are made upof a networksection, anoptionalsubnet section, and a host section,
asshown in thefollowing example:
192.168.0.1
Designating Port ID
Each telephony port of the ITGis assigned withanID. Somecommands requireatelephony
port ID. TheITG assigned ID 0to the firsttelephonyport, ID1to the 2nd port, and soon.
DocumentationAbbreviations
Throughout this document,the user will comeacross anumber of abbreviations, someof
them are commonlyused inthe industry and some areuniquetothe ITG.The usershould be
familiarwith the following abbreviations:
ATPM Address Translation and Parsing Manager
CLI Command LineInterface
DHCP Dynamic Host Configuration Protocol
DIS Digital IdentificationSignal
DNS DomainName System
DSP Digital Signal Processor