Active Care Medical Renegade User manual

Insert the armrests into the attachment points
in the seat frame so that the armrests face
forward.
Installtheseatpost.Ensurethattheseatpost
isalignedsothatthe twoflangeswith holesare
facingthe rearof the product.Having these flanges
rotatedinto anyother positionwill resultin instability
inthe seat.
Onthe Medalist, remove the two knobs on the
covershroud then lift up carefully on the cover
shroudto remove.
Attach the two battery connectors to the
batteries (red to red and black to black).
Remove your wheelchair from its packaging.
Onthe Renegade, lift upcarefully on the cover
shroudto remove.
Replace the cover shroud. The shroud must
slide over the brake levers, which should be
positioned in the engaged mpde. On the Medalist,
replace and tighten the two knobs removed in Step
1b.
Frombehindthe product,looking forward,insert
theseat boltinto hole onthe leftside of theseat
post.This bolt is also used to adjustthe seat height.
Insertthe bolt asfar into thehole as itwill go, making
sure that the bolt passes all the way through to the
holeon the opposite side.Install the washer andnut
andtighten them usingthe included flatwrench.
Lifttheseatandpulltheswivelleverupatthe
sametime.Lowerthebottomoftheseatonto
theseat post. Release thelever,swivel the seat
and push down on the seatuntilitlocksinplace.
1NOTE: Get help when placing the seat onto the
post to avoid scratching the cover shroud.
1a. 1b. 2. 3.
4. 5. 6. 7.
Quick Start Guide
Renegade/Medalist
Please Read Before Operating!
Your wheelchair is packaged with a packet of tools you will need for initial setup.
Please locate this packet first.

Connectthe main cable fromthecontroller to
the connection port in the product’s cover
shroud.
Insertthecontroller’ssquare tubeinto thetube
under the armrest. Tighten the bolt on the
undersideof thecontroller armtubeto holdit inplace
atthe desired extension.
Medalist/Renegade Quick Start Guide
READ BEFORE UNPACKING
This Quick Start Guide offers basic information on initial product setup only. Read the owner’s
manual and all supplemental information thoroughly before operating the product for information
on safety, battery charging, basic operation, comfort adjustments, disassembly and care and
maintenance.
NOTE:The illustrations provided may not reflect your actual unit.
Apparent Loss or Damage
Should visual inspection upon receipt of this shipment show loss or damage, it must be noted on the freight bill
or express receipt and signed by the carrier’s agent. Failure to do this may result in the carrier refusing to
honor claim.
The carrier will forward you the necessary form(s) for filing claim.
Concealed Loss or Damage
When loss or damage is not apparent until the unit is unpacked, then a claim for concealed damage is entered
by the receiver.When damage us discovered, make a written request to the carrier for inspection.
Keep all cartons and fillers.You must make this request for inspection within twenty-four (24) hours of the
delivery.The carrier will furnish you with an inspection report and the necessary form(s) for filing concealed
damage or loss claim. It is the receiver’s responsibility to file such claims for concealed damage.
READ
THIS
FIRST!
8.
Insertandtighten theincludedstar knobsto lock
thearmrests into place at the desired width.
9.
Affix the headrest to the top of the seat by
inserting the headrest posts into the holes in
thetop of the seat.
10. 11.
Fullycharge the wheelchair’s batteriesby inserting the roundcharger connector intothe battery charging
terminalonthe frontof thewheelchair’scontrollerand insertingthe 3-prongedplug intoa standardelectrical
outlet.
Ensurethat the 115V/230V switchonthe product’sbattery charger is setto 115V.If the switchis set to230V,the
scooter will not charge properly.Fu ll charging normally takes 6-8 hours, but can take as many as 10 hours
dependingon the batteries’ charge levelwhen starting and the ambienttemperature.
12.