human care Nexus 1 User manual

THIS MANUAL MAY NOT BE REPRODUCED IN PART OR IN WHOLE
WITHOUT THE WRITTEN PERMISSION OF THE PUBLISHER.
USER MANUAL
ASSEMBLY/BRAKE USAGE/BRAKE ADJUSTMENT GUIDE
FOR MODELS:
Nexus 1
Nexus 2
READ ALL WARNINGS CAREFULLY
BEFORE USING YOUR WALKER.
KEEP THIS INFORMATION
FOR FUTURE REFERENCE.
IF YOU HAVE A PROBLEM:
DO NOT aempt to repair the walker yourself.
Call the store where the walker was purchased. Most stores do repairs and
will re-order parts for you. If your supplier is unable to assist you, please
call Human Care at 1-613-723-6734 or e-mail at info.ca@humancaregroup.
com.

THIS MANUAL MAY NOT BE REPRODUCED IN PART OR IN WHOLE
WITHOUT THE WRITTEN PERMISSION OF THE PUBLISHER.
USER MANUAL
WARNINGS: READ CAREFULLY
Be sure brake is locked before
sing on seat.
DO NOT use on stairs or escalators.
Only use this product on even
surfaces clear of obstrucons.
DO NOT use brake handles when
sing and standing. Use upper
handgrip only to stabilize your
body.
DO NOT squeeze brake connu-
ously while walking as this will
cause premature wear to the
brake pad and re.
DO NOT rest anything on backstrap
as damage may occur.
DO NOT lean on one side of
the walker when sing down.
Distribute weight evenly to
prevent the walker from pping
over.
Touch the back of your legs to seat
before sing.
DO NOT exceed weight capacity!
250lb / 113.4kg
DO NOT put anything on your folded
walker as this will cause damage to
the frame, plasc parts, etc.
DO NOT leave your walker
unaended. Anyme the walker
has been out of view (eg. placed
in vehicle, etc.) inspect the walker
completely for any signs of damage
before use.
IMPORTANT!
Failure to adhere to warnings can lead to serious injury or
death. Read and understand all warnings prior to using
this product.
CAUTION!
This product must always be inspected prior to use for
any signs of wear or damage. DO NOT use this product
if it is missing any components or is damaged in any way.
DO NOT use as a wheelchair/ transport
chair. The walker has not been designed
for this purpose.
If the walker has been stored in any
type of transportaon, such as a plane,
train, boat, bus, car, etc. you run the
risk of damage to the walker and to any
of its components. Please inspect very
carefully before usage.

THIS MANUAL MAY NOT BE REPRODUCED IN PART OR IN WHOLE
WITHOUT THE WRITTEN PERMISSION OF THE PUBLISHER.
USER MANUAL
CARE AND USE
DO NOT use chlorine bleach
or abrasive cleansers. To
clean, wipe down with a
damp cloth using a mild
detergent only.
INSPECT your walker every
year by an authorized
dealer/service agent. Only
let an authorized personnel
adjust your walker.
This is a walking aid only
designed to assist you with
mobility. Only use the seat
for rest periods.
CHECK periodically to
ensure that the black height
adjustment knobs are
ghtened securely.
CHECK your walker
frequently for any loose,
cracked or corroded plasc
or metal components.
CHECK your walker to
ensure the front forks and
all wheels swivel easily
and are clear of any dirt or
obstrucons.
DO NOT store the walker
near a heat source.
DO NOT leave your walker
exposed to the elements
(weather).
Use only authorized parts/
accessories with your
walking aid.
NEVER use the walker for
any other reason other
than for its intended
purpose.
USING YOUR WALKER
This walker is designed for use as a walking aid and should
never be used for any other purpose.
TO SIT, touch the back of your legs to the edge of the seat to ensure
posion of walker before sing down.
DO NOT support your weight on the handles when aempng to sit.
Use the handles to stabilize your body as you carefully turn around.
Keep your hands on the foam handles and slowly lower your weight
onto the seat.
IMPORTANT: Test to be sure
walker will not roll before
aempng to sit. Brakes must
be in parked/locked posion.
Ensure when walking your path is clear and free of obstacles
to avoid injury and damage.

THIS MANUAL MAY NOT BE REPRODUCED IN PART OR IN WHOLE
WITHOUT THE WRITTEN PERMISSION OF THE PUBLISHER.
USER MANUAL
ASSEMBLY
Remove the height adjustment
screws from handles.
Slide handles into frame and
insert height adjustment screws to
desired height.
Place screw head through the
adjustment hole from the inside of
the walker frame (be sure the hex
screw ts into cut out in plasc
collar.
From the outside of the frame
ghten the black adjustment knob
onto the screw.
Slide the backstrap into the clamp.
The padded side of the backstrap
faces the inside of the walker (your
back should rest on the padding
when seated).
Secure backstrap into posion
with screw and nut.
Add the basket to the crossbar
supporng the seat using the
hooks.
Brakes must be in the parked/locked posion
before sing on the walker!
Cauon: DO NOT overload basket.
Maximum Load: 10lb/5kg
OPENING/FOLDING
TO FOLD
PULL UP on the
nylon strap located
in the middle of the
seat.
PUSH DOWN on
the seat to lock into
place.
IMPORTANT!
If using the walker parally
folded, ensure all four
wheels rest rmly on the
ground.
CAUTION!
Never sit on the seat unless
it is locked into place and the
brakes are in the parked/
locked posion.
PULL APART push handles
to open the walker into the
proper walking posion.
Raise the walker to rest the
rear wheels while pulling
apart.
CAUTION!
Do not drop your weight
onto the seat as this may
cause damage to the seat
and its components.
Ensure that all bolts are securely fastened before
using the walker!

THIS MANUAL MAY NOT BE REPRODUCED IN PART OR IN WHOLE
WITHOUT THE WRITTEN PERMISSION OF THE PUBLISHER.
USER MANUAL
BRAKE USAGE/ADJUSTMENT
LOCK THE BRAKE by pushing down on the
handle (for loop handle, push down on the ball
located at the end of the handle). The handle
will lock into a downward posion when
properly engaged.
RELEASE THE BRAKE by pulling up on the
handle. BRAKE FOR SPEED CONTROL by
squeezing on the handle.
IF THE HAND BRAKE IS TOO LOOSE
loosen the Locking Nut and turn the
Tension Adjustment Screw CLOCKWISE.
NOTE: If addional
adjustment is required,
repeat one full turn at a
me. Once adjusted, make
sure the Locking Nut is spun
ght against the Housing.
This will prevent the Tension
Adjustment Screw from
loosening.
FEATHER TOUCH HAND BRAKING SYSTEM
1
2
3
4
5
1. Locking Nut
2. Tension Adjustment Screw
3. Housing
4. Handle
5. Brake Handle Arthric Ball
When receiving your new walker, the brake
system will be preset from the factory. To
maintain this preset posion, be sure that the
Locking Nut is ght against the Housing. This
is the same for the Tension Adjustment Screw
Locking Nut located at the rear wheel. (To adjust
see: Brake Usage/Adjustment)
UNDERSTAND YOUR ROLLATOR
Backstrap
Brake Handle
Star Handle
and Bolt
Seat Strap
Crossbar
Basket
Arthric
Ball
Tension
Adjustment
Screw
Push Handles
Backstrap Clamp
Product name
Article number
Maximum user weight
Date of manufacture,
BATCH number and
address of manufacture.
UPC code
CODE 39 barcode,
Serial number
Seat height
Product width
Indoor / outdoor use

THIS MANUAL MAY NOT BE REPRODUCED IN PART OR IN WHOLE
WITHOUT THE WRITTEN PERMISSION OF THE PUBLISHER.
USER MANUAL
Serial Number
(Located on Right Rear Leg)
Date of Purchase
PRODUCT INFORMATION
Made in Malaysia
HUMAN CARE HC AB
Fabriksvägen 2
245 34 Staanstorp Sweden
Your dealer:
99161-ENG Rev B(2014-02-21)