ActiveAqua AAPW40 User manual

INSTRUCTION MANUAL
ACTIVE AQUA
SUBMERSIBLE PUMP
Acve Aqua Pumps from Hydrofarm are carefully inspected and
tested to ensure both safety and operang performance. However,
failure to follow the instrucons and warnings in this manual may
result in pump damage and/or serious injury. Be sure to read and
save this manual for future reference.
LIMITED WARRANTY
Your Acve Aqua Pump is guaranteed to work for one year from the
date of retail purchase. Replaceable lter material not included. Save
your retail receipt/invoice, a copy is required for all warranty work.
Any alteraons to a pump or cord will void warranty. Contact the place
of purchase for repair or replacement. Acve Aqua Pumps are sold and
serviced only through dealers.
FOR MODELS: AAPW40, AAPW160, AAPW250,
AAPW400, AAPW550, AAPW800, AAPW1000
AAPW250/400
AAPW800/550
AAPW1000 AAPW160
AAPW40
AASubPump_Instr.11
SYMPTOM CAUSE SOLUTION
The pump does not run Power is not turned on
Incorrectly plugged in
Bound impeller
Turn on the power
Plug in correctly
Remove foreign matter from impeller
The motor repeats ON/OFF
without running pump. It stops
and does not restart
Wrong voltage
The water intake or outlet pipe
is clogged with foreign matter
Correct voltage
Clean out the intake and outlet
The pump runs with reduced or
no performance
Wrong frequency
Impeller worn out
Low water level
Correct frequency
Replace impeller
Ensure the pump is fully submerged
The pump runs normally at the
beginning but the water ows
sluggishly or there is no water
Hose is too long or clogged
Air in the impeller chamber
Shorten hose and/or clean out
To get rid of air, put pump into the
water. Turn the switch to“ON”and“OFF”
intermittently to clear air from pump
TROUBLESHOOTING GUIDE









www.hydrofarm.com
AAPW40 43 (163) 5 (19) 3 5/16" (8mm)
AAPW160 172 (650) 15 (57) 9.5 1/2" (12.7mm)
AAPW250 291 (1,100) 25 (95) 16 1/2", 3/4" (12,7mm, 19mm)
AAPW400 370 (1,400) 40 (151) 24 1/2", 3/4" (12.7mm, 19mm)
AAPW550 529 (2,000) 55 (208) 33 1/2", 3/4" (12.7mm,19mm)
AAPW800 793 (3,000) 80 (303) 58 1/2", 3/4", 1" (12.7mm,19mm, 25mm)
AAPW1000 1110 (4,200) 100+ (378+) 92 1/2", 3/4", 1" (12.7mm,19mm, 25mm)
WARNING
• This pump is supplied with a grounding conductor and a grounding type aachment
plug. To reduce risk of electric shock, connect only to a properly grounded outlet.
• Do not remove the grounding pin from the plug.
• Do not connect to any voltage other than that shown on the pump.
• Do not pump ammable liquids.
• The naonal electric code requires that a grounded fault circuit interrupter (GFCI)
be used in the branch circuit supplying fountain pumps and other pond equipment.
See your electrical supplies dealer for this device.
• Do not use with water above 86°F (30°C).
• Do not allow the pump to freeze in winter, remove pump from fountains and ponds
and store in a frost-free area.
CAUTION:
Always disconnect from electrical outlet before handling the pump.
Do not let the pump run dry.
Do not li the pump by the power cord.
Do not pump heated liquids.
Do not operate in salt water.
PERFORMANCE
• A clogged or dirty intake screen will greatly reduce performance. If the pump is
used on a dirty surface, raise it slightly to reduce the amount of debris contacng
the intake. If less ow is desired, adjust the ow control knob on the front of the
pump or restrict the discharge ow.
• This pump can be used submersed or in-line. Note that when used in-line it should
be placed below the water level since it is not self priming. Never run this pump
dry. If inially the pump does not work, it may be “air locked”. To clear the air lock,
unplug the pump and rotate 180 degrees under water, repeat if necessary.
The included gray ng should be aached to the inlet side of the pump only when
operated in-line. The barbed gray and black ngs use a dierent sized thread and
rubber O-rings. The gray in-line ng aaches to the front of the pump and uses
the larger sized O-ring. The black ngs aach to the top of the pump and use the
smaller sized O-ring. Please use only as intended (see chart for reference).
Product
Item Code
Rated
GPH (LPH)
Recommended Size
gallons (litres,litros)
Was Fing Sizes Included
inches (milimeters)
0
2
4
6
8
10
12
0 200 400 600 800 1000 1200
HEAD (FT) HEIGHT
GALLONS PER HOUR (LPH) VOLUME
AAPW1000
800
550
160
40
400
Pump Gallons Recommended
Model Per Hour Reservoir Size
AAPW1000 1110 100+ Gallon
AAPW800 793 80 Gallon
AAPW550 529 55 Gallon
AAPW400 370 40 Gallon
AAPW250 291 25 Gallon
AAPW160 171 15 Gallon
AAPW40 43 5 Gallon
Active Air Submersible Pump Comparison Chart
250
ACTIVE AQUA SUBMERSIBLE PUMP COMPARISON CHART
Intake ngs are not represented in this chart.
Each aeraon kit contains an extra ng.
61

www.hydrofarm.com
MAINTENANCE
To clean the pump, remove the front cover and the impeller. Use a small brush and stream
of water to remove any debris.
IF THE PUMP FAILS TO OPERATE, CHECK THE FOLLOWING:
• Check the circuit breaker and try another outlet to ensure the pump is geng
electrical power. NOTE: Always disconnect from electrical outlet before handling
the pump.
• Check the pump discharge and tubing for kinks and obstrucons. Algae buildup
can be ushed out with a garden hose.
• Check the inlet screen to ensure it is not clogged with debris.
• Remove the pump inlet to access the impeller area. Turn the rotor to ensure it is
not broken or jammed.
• Monthly maintenance will add to your pump’s life. NOTE: Ensure that the
electrical cord loops below the electrical outlet to form a “Drip Loop.” This will
prevent water from running down the cord into the electrical outlet.
AAPW160
Outlet O ring
C M Y
CM MY CY
CMY
K
AAPW160–EXILUUS.pdf 1 2/17/12 9:23 AM
Sucon cups
Sucon cups
Back
cover
Impeller
cover
Impeller
cover
Impeller
Motor
Motor
Intake O ring
Front
cover
Front
cover
Intake screen
foam
Flow control lever
AAPW40
Water outlet
Impeller
Back cover
Tube
ngs
EDGE OF TANK
MUFFLER
CONNECTOR
AIR VALVE
AERATION KIT
AERATION KIT
INTAKE INSTRUCTIONS: The Venturi
intake provides air inducon when
the airline is connected to the small
air intake port on the included hose
ng. Aach the air muer to
the air control valve using the tube
connector.
Aach the air control assembly to the
Venturi air port on the included hose
ng. Keep the air valve and muer
assembly above the water surface
level. This pump can be used with or
without the Venturi air intake.
25

www.hydrofarm.com
O ring
Impeller
Sucon cups
Outlet O ring Back cover
Motor
Tube ngs
Sha
bushing
Front cover
Intake screen foam
AAPW250, AAPW400, AAPW550, AAPW800, AAPW1000
Fing for inline funcon
Flow control
knob
Impeller cover
43