AcueLighting HALO Sport 100 User manual

（RDM!"#$#%&'()*$+,!-#."/&#*0%+1(#23
User4s Manual

Chapter 1: Installation, Safety, Maintenance
1.1 Maintenance
lTo reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
lIntermittent usage will extend this fixtures service life.
lPlease clean the fan, fan cover, and optical lens in order to keep in good working condition.
lDo not use alcohol or any other solvent to clean the shell.
1.2 Statement
The product performance and packaging has been tested before shipping. All users should strictly
comply with the warning and operating instructions as stated. Any misuse and damage as a result
of use outside of the guidelines herein will result in a voided warranty. Any fault or problem
caused by neglecting instructions in this manual will not be covered by warranty.
Note: All information is subject to change without prior notice.
1.3 Safety Precaution
lIn order to guarantee the product’s life, please do not put it in damp places or any
environment over 140 degrees.
lAlways mount this unit in a safe and stable manner.
lA professional engineer should perform the install or removal of the fixture.
lPlease restart 20 minutes after turning off light. The fixture must be cool before restarting.
Frequent switching will reduce the life span of LED source and power supply; intermittent
usage will improve the life of the fixture.
lIn order to make sure the product is used correctly, please read the manual carefully.
1.4 Product Specification
lLight Source: 1pcs * 100W White LED
lChannel mode: 14 DMX512 Channel
lPan scan：540°(16bit) Electric correction
lTilt scan：270° (16bit) Electric correction
lColor wheel: 7color + white
lGobo: Fixed Gobo 7 + white, Rotation Gobo 6 + white

lPrism: 3 prism
l0-100% mechanical dimming, mechanical dimming and free dimming available.
lPower Input: 100-240V，50/60Hz
lMax Power Consumption: 200W
lIP level: IP20
1.5 Cable connection (DMX)
Use a cable compliant to the specifications of EIA RS-485: 2-pole twisted, shielded, 120 Ohm
characteristic impedance, 22-24 AWG . Do not use microphone cable or other cable with characteristics
differing from those specified. The end connections must be made using XLR type 3 pin male/female
connectors. A terminating plug must be inserted into the last fixture with a resistance of 120 Ohm (minimum
1/4W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the
connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors
(ground).
!
Figure 1 DMX Cable connection
1.6 Rigging (Optional)
This equipment can be positioned and fixed by a clamp in any direction.
Attention! One clamp and one safety cable are needed to attach the equipment safely.
Attention! Fasten a safety cable to the eye-bolt hole under the fixture. The safety cable must never
be mounted to the handle or any other part of the fixture.
lCheck if the rigging bracket or clamps are damaged before every use. The mounting surface
must be able to withstand ten times the weight of the equipment. Make sure the structure and
mounting point can withstand ten times the weight of all the equipment installed in same
location.

lMounting screws on the clamp/mounting solution must be tightened firmly.
lMake sure to install safety cable.
lKeep a distance of more than 1M between fixture and any flammable material or lighting
source.
Chapter 2. Menu Operation
Within the main menu you can enter 6 sub menus, shown in Error! Reference source not found..
Sub menus include class of parameter and status:
lADDR：Set light DMX address.
lMODE：Set light operation mode: master or slave mode when in auto run mode.
lDISP：Set display parameter, ex. Language select.
lSCENE：Used for manually testing fixture, modifying DMX channel data to test function，or
for reference channel functions using DMX table.
lADVA：Set light running parameter.
lSTAT：view current status of fixture.

Chapter 3 DMX Channel Chart
Channel table
CHANNEL
NAME
VALUE
DESCRIPTION
CH1
Strobe
0-3
Shutter Closed
4-127
Slow strobe to fast strobe
128-191
Slow strobe to fast strobe(mode 2)
192-251
Slow strobe to fast strobe
252-255
Shutter Open
CH2
Dimmer
0-255
0-100% Dimmer
CH3
PAN
0-255
0-540
CH4
TITL
0-255
0-270
CH5
XY speed
0-255
Fast to slow
CH6
Color
0-7
White
8-15
White + Color1
16-23
Color1
24-31
Color1 + Color2
32-39
Color2
40-47
Color2 + Color3
48-55
Color3
56-63
Color3 + Color4
64-71
Color4
72-79
Color4 + Color5

80-87
Color5
88-95
Color5 + Color6
96-103
Color6
104-111
Color6 + Color7
112-119
Color7
120-127
Color7 + White
128-190
Rotate forward (fast to slow)
191-192
Stop
193-255
Rotate reverse (slow to fast)
CH7
Static Gobo
0-9
White
10-19
GOBO1
20-29
GOBO2
30-39
GOBO3
40-49
GOBO4
50-59
GOBO5
60-69
GOBO6
70-79
GOBO7
80-84
Shake slow to fast GOBO1
85-89
Shake slow to fast GOBO2
90-94
Shake slow to fast GOBO3
95-99
Shake slow to fast GOBO4
100-104
Shake slow to fast GOBO5
105-109
Shake slow to fast GOBO6

110-127
Shake slow to fast GOBO7
128-190
Rotate forward (fast to slow)
191-192
Stop
193-255
Rotate reverse (slow to fast)
CH8
Rotating
Gobo
0-9
White
10-19
GOBO1
20-29
GOBO2
30-39
GOBO3
40-49
GOBO4
50-59
GOBO5
60-69
GOBO6
70-79
Shake slow to fast GOBO1
80-89
Shake slow to fast GOBO2
90-99
Shake slow to fast GOBO3
100-109
Shake slow to fast GOBO4
110-119
Shake slow to fast GOBO5
120-127
Shake slow to fast GOBO6
128-190
Rotate forward (fast to slow)
191-192
Stop
193-255
Rotate reverse (slow to fast)
CH9
Gobo
ROT
0-127
0-400
128-190
Rotate forward (fast to slow)
191-192
Stop

193-255
Rotate reverse (slow to fast)
CH10
Prism
0-19
None
20-63
Insert prism
64-255
Rotate reverse (slow to fast)
CH11
Focus
0-255
Near to far adjust
CH12
PAN Fine
0-255
0-255 Fine pan adjust
CH13
TILT Fine
0-255
0-255 Fine tilt adjust
CH14
Halo light
strobe
0-10
Off
11-249
Slow to fast strobe
250-255
Opening
CH15
Halo light
effect
0-3
OFF
4-7
R
8-11
G
12-15
B
16-19
R+G
20-23
G+B
24-27
R+B
28-31
R+G+B
32-59
Mixed color 1
60-95
Mixed color 2
96-127
Background
128-149
Slow to fast gradient
150-199
Slow to fast transition color

NOTES:________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
200-255
Slow to fast transition color
CH16
RESET
0-25
None
26-76
Reset for more than 3 seconds XY
77-127
Reset effect motor for more than 4 seconds
128-255
Reset all over 5 seconds