AcueLighting Extreme 150 Hybrid User manual

Extreme 150 Hybrid
Instruction Manual

Table Of Contents
1. Instructions-------------------------------------------------------------------------------------------2
1.1 Application According to Purpose------------------------------------------------------------------2
1.2 Indoor use only------------------------------------------------------------------------------------------2
1.3 Safety operation----------------------------------------------------------------------------------------2
2. LED Lamp ---------------------------------------------------------------------------------------------3
3. Power Connections---------------------------------------------------------------------------3
4. Housing ------------------------------------------------------------------------------------------------4
5. Operating Requirements-----------------------------------------------------------------4
6. Installation ------------------------------------------------------------------------------------------ 5
7. Operation------------------------------------------------------------------------------------------- 6
7.1 Controls-------------------------------------------------------------------------------------------------- 6
7.2 Menu Structure----------------------------------------------------------------------------------------- 6
7.3 Channel--------------------------------------------------------------------------------------------------7
8. Fuse Replacement---------------------------------------------------------------------------9
9. Maintenance instructions -------------------------------------------------------------9
10. Technical Parameters ------------------------------------------------------------------9
1

Thank you for choosing Acue Lighting Products
For your safety and the safety of others, do not modify this product in any way. Please note that damage
caused by improper use, regular wear and tare, and misconduct with the product is beyond the scope of our
warranty. Warranty only covers manufacturers defects for the amount of 1 year from purchase.
This equipment has passed strict testing and inspection before shipment. Please refer to the instruction manual’s
section under operation requirements (section 5), to ensure the safe operation of the product under normal
conditions. Any damage caused by improper operation will void all warranty claims. Manufacturer does not accept
any liability due to improper operation of its products or non-compliance of the instructions in this manual of any
of any kind.
Please place the manual in a safe place for future reference.
1. Instructions
1.1Application According to Purpose
lThis product is a stage lighting luminaire, which creates special light effects using an LED light source. To
generate these effects, the product must be connected to a proper power source and a DMX-512 compatible
controller.
lThis product is designed for 110/230V, 50/60Hz operation and exclusively for indoor use.
lIf used for any purpose other than described in these operating instructions, the device may suffer damage
and cause the warranty to be void.
lThe manufacturer's serial number must never be removed as otherwise the warranty will be void.
lSafety and Maintenance checks must be done routinely to avoid any damages to the product and the
surroundings.
1.2 Indoor use only
lMake sure the equipment load-bearing structure (ceiling, wall, or truss) can withstand the weight of more
than 10 times of fixture when installed above ground.
lDisconnect all power input to power supply before replacing lamp, fuse or other accessories
lOnly operate under proper electrical standards not to overload circuits.
lCool down for 15 minutes before replacing lamps. Please do not use other company's accessories.
lContact your specialized dealer for any technical problems or issues
1.3 Safety operation
lDo not operate without outer cover or lenses
lDo not look directly to the light
lReplace immediately when lamp broken
lDo not project directly to items near 0.5M
lDo not operate in temperature over 45 °C
2

ATTENTION:
DANGER OF LIFE! RISK OF BURNS!
RISK OF FIRE!
ATTENTION:
DANGER OF LIFE! RISK OF BURNS!
RISK OF FIRE! RISK OF SHORT CIRCUIT!
ATTENTION:
DANGER OF LIFE! RISK OF BURNS!
RISK OF FIRE! RISK OF SHORT CIRCUIT!
2. LED Diodes
During operation, the lamps will reach temperatures of up to 75° C. Touching the lamps may cause serious
burns! Objects coming into contact with the lamps during and shortly after operation may catch fire!
3. Supply Voltages, Mains Cord and Connection to Mains
lThe handling of supply voltage, mains cords and connections to mains calls for particular care considering
the risk from a life-threatening electric shock, the risk of fire and the risk of short circuits! Please observe the
following notes in particular:
lProducts operating on supply voltage should be kept out of the reach of children. Therefore ensure the
permanent supervision if children are in the immediate vicinity of the product!
lFor commercial facilities the regulations on the prevention of accidents of the respective trade association
must be observed. The operation of this equipment at schools, training facilities, and hobby or self-help
workshops must be supervised responsibly by trained personnel
lCheck the product regularly for any damage to the mains cord! Should you discover any damage to the
mains cord, do not operate or disconnect this product! Secure the product against accidental operation and
contact your specialized dealer Always separate the product from mains by holding the mains plug by the
handling surface. Never disconnect by holding the line cord! Be sure to connect the product exclusively to
230 V, 50 Hz A/C!
lAlways ensure during installation, operation, transportation, and when storing the product that the mains
cord is not exposed to possible mechanical damage, or damage caused by humidity, fluids, heat or cold!
lThe product's power input connector must not be exposed to stress from pull. Connect the mains connection
once the product has been installed only. Always connect the mains plug last.
lThe product must only be connected to a proper power outlet. Connect the mains cord to suitable outlets
only. Use extensions cords in compliance with specifications only. Do not allow the mains cord to come into
contact with any liquids.
lEnsure during installation, operation, transport and storage that none of the cables are freely exposed or
damaged.
lNever touch the mains cord, mains plug and outlets with wet or damp hands.
lWhen not using the product, and prior to cleaning always disconnect the product from mains. To do so, hold
the mains plug by the handling surface and never pull from the mains cord itself.
lNever connect the device to dimmer packs.
4. Housing
lAlways ensure during installation, operation, transport and when storing the product that no force or other
impact has damaged the housing!
lThe housing must not touch onto any other devices or objects during operation!
lEasily flammable materials, e.g. decoration material and other surfaces and objects, must maintain a
minimum distance of 3m to the housing! Walls must be a minimum distance of 50cm to the housing! The
device must only be installed on a fireproof surfaces (no carpet)! Always ensure a proper circulation of air.
lDo not touch the housing during operation. The housing is safe to touch approx. 5 minutes following the end
of operation as it will heat up during operation.
The device must never be carried via the projector arms. Use the carrying handles only!
3

ATTENTION：
DANGER OF LIFE!
Fluids must not enter the housing as this could reduce the protective insulation and may trigger short circuits,
which may lead to a fatal electronic shock! If fluids have entered, disconnect the mains plug immediately and
secure the product against unintentional operation and contact your dealer for further instructions. Damage caused
as a result of fluids entering the housing is exempt from warranty.
No metal parts or other items must enter the housing as this may reduce the protective insulation or trigger
short circuits which may lead to fatal electric shocks. If metal parts or other items have entered, disconnect the
mains plug immediately, secure the product against unintentional operation and contact your specialized dealer!
Damage caused by metal parts or other items in the housing is exempt from warranty.
5. Operating Environment
The product must be operated and stored in a dry environment only. Splash water, rain, humidity, or fog may
reduce the protective insulation, which may lead to fatal electric shocks! The limit value for relative humidity is
50% at 45° C. A minimum distance of 1.5m to a fog machine must be observed; fog saturation in the room must
not reduce the visibility to below 10m.
The product must be operated at a temperature range of between -5 ° C and 45 ° C only. Protect the product
against direct exposure to sunlight or other heat, such as from radiators. If the product is taken from a cold
environment into a warm environment it must only be taken into operation once it has reached ambient
temperature, since the condensation created by the difference in temperature may cause damage to the luminaire.
Protect the product against dust. Dust may reduce the protective insulation, which may cause fatal electric
shocks.
The product must be operated at altitudes ranging between 20m below and 3000m above sea level only!
The product must not be operated during thunderstorms to avoid risk of damage from surge voltages!
6. Installation
This product can be operated suspended from a ceiling or truss structure.
Should your lighting effect show any signs of damage, do not install the device. In this case, have your
lighting effect repaired by an authorized dealer. The manufacturer does not accept responsibility or liability for
damage to property or personal injury resulting from an improper installation.
As a stand-alone system the device must be installed vertically on an absolute planar, firm, shock- and
vibration-free surface. The installation of this lighting effect must be carried out by trained and professional staff.
The installation of this lighting fixture must only be carried out with the appropriate safety and hanging materials.
The suspended installation of this lighting effect necessitates a suitable suspension system. The lighting effect
must never be fixed to a swinging platform.
It is a must to install this device with a second independent fastening system (ex. Safety cable or strap). Such
second fastening system must guarantee in the event of failure of the main fastening system that no assembly parts
will fall down. The second fastening system must only be connected to the bottom of the fixture base in the proper
mounting location.
The light effect unit must be attached via two certified hooks and omega bracket when mounted to truss. Use
of properly weight rated mounting options must be used when mounting to other surfaces• Use the screw threads
on the under-surface of brackets only.
4
ATTENTION:
DANGER OF LIFE! RISK OF BURNS!
RISK OF FIRE! RISK OF SHORT
CIRCUIT!

ATTENTION：
RISK OF HEALTH!
It must be ensured that an expert inspects the mechanical and safety-relevant installation prior to the initial
operation and following major modifications, prior to the renewed operation. It must be ensured that an expert
inspects the mechanical and safety-relevant installation at least once a year. It must be ensured that an expert
inspects the mechanical installation and the installation of relevance to safety within the framework of an
acceptance test at least every four years.
The installation method must be as such that it can withstand 10 times the load capacity without harmful
deformation for a period of 60 minutes.
The light effect unit must be secured by a safety cable if fly-mounted. The cable must withstand 12 times the
weight of the light effect unit. Use arrester cables equipped with quick closing links. The dropping distance must
not exceed 20 cm. Defect arrested cables or arrested cables that have already been exposed to stress must not be
used.
7. Operation
7.1 Controls
Link all DMX devices with a DMX-512 controller by using a standard, 3-pin DMX cable or 5-pin DMX
cables. Connect the output of the first device with the input of the second device and the output of the second
device with the input of the third device and so on.
Connect the mains plug to an outlet.
Operating the product for the first time may generate smoke and odor; this is not a defect. Avoid
disconnecting the product repeatedly and quickly from mains. Always wait 15 minutes prior to the next
disconnection
7.2 Menu Structure
5

System setup System setup
Fixture ID
Chanel mode
Invert Pan
DMX
Autorun 1
Autorun 2
Sound
0~255
18CH
ON
No Signal
Keep
clean
Screen saver
ON
OFF
Language
Chinese
English
Load default
Manual Drive Chanel 0~255
Motor Calibration Password
System Test
System Info
Auto test
Firmware version
ID temperture
D M X
Run mode
OFF
Invert Tilt
ON
OFF
Swap XY
ON
OFF
Encoder
ON
OFF
MIC
DMX Address 1~512
Mo tor
Password
6

7.3 DMX Channels
Channel
Function
Value
Description
1
Dimmer
0-255
From dark to bright
2
Strobe
0-10
No effect
11-255
Strobe from slow to fast
3
Pan
0-255
Pan
4
Pan fine
0-255
Pan 16 bit
5
Tilt
0-255
Tilt
6
Tilt fine
0-255
Tilt 16 bit
7
Pan/tilt speed
0-255
Speed from fast to slow
8
Color
0-4
white
5-9
White + color 1
10-14
Color 1
15-19
Color 1+color 2
20-24
Color 2
25-29
Color 2+color 3
30-34
Color 3
35-39
Color 3+color 4
40-44
Color 4
45-49
Color 4+color 5
50-54
Color 5
55-59
Color 5+color 6
60-64
Color 6
65-69
Color 6+color 7
70-74
Color 7
75-79
Color 7+white
80-167
Clockwise rotation from fast to slow
168-255
Anti-clockwise rotation from slow to fast
Fi
Fixed gobo
Open
0-4
Gobo 1
5-9
Gobo 2
10-15
Gobo 3
15-19
Gobo 4
20-24
Gobo 5
25-29
Gobo 6
30-34
Gobo 7
35-39
Gobo 8
40-44
Gobo 9
45-49
Gobo 10
50-54
Gobo 1 shake
55-59
Gobo 2 shake

Fixed gobo
60-64
Gobo 3 shake
65-69
Gobo 4 shake
70-74
Gobo 5 shake
75-79
Gobo 6 shake
80-84
Gobo 7 shake
85-89
Gobo 8 shake
90-94
Gobo 9 shake
95-99
Gobo 10 shake
100-177
Anti-clockwise rotation from fast to slow
178-255
Clockwise rotation from slow to fast
10
Rotation gobo
0-9
Open
10-19
Rotation gobo 1
20-29
Rotation gobo 2
30-39
Rotation gobo 3
40-49
Rotation gobo 4
50-59
Rotation gobo 5
60-69
Rotation gobo 6
70-79
Rotation gobo 1 shake
80-89
Rotation gobo 2 shake
90-99
Rotation gobo 3 shake
100-109
Rotation gobo 4 shake
110-119
Rotation gobo 5 shake
120-129
Rotation gobo 6 shake
130-193
Anti-clockwise rotation from fast to slow
194-255
Clockwise rotation from slow to fast
11
Gobo rotation
0-127
Gobo angle
128-190
Clockwise rotation from fast to slow
191-192
Stop
193-255
Anti-clockwise rotation from slow to fast
12
Focus
0-255
Focus
13
Zoom
0-255
Gobo zoom
14
Automatic focus
0-9
No effect
10-255
Auto adjustment of zoom with focus
15
Frost
0-127
Empty
128-255
Frost
16
Prism
0-127
Prism off
127-255
Prism on
17
Prism rotation
0-127
Prism angle
128-190
Anti-clockwise rotation from fast to slow

191-192
Stop
193-255
Clockwise rotation from slow to fast
18
Macro function
0-5
No effect
6-55
Mode 1
56-105
Mode 2
106-155
Mode 3
156-205
Mode 4
206-255
Random mode
19
Reset
0-25
No effect
26-76
Small motor reset after 5 seconds delay
77-127
XY reset after 5 seconds delay
128-255
Whole unit reset after 5 seconds delay
8. Replacement of Fuse.
Disconnect the product from the mains prior to changing a fuse.
Only replace the fuse by a fuse of same type and rating. An incorrect fuse could damage the lighting effect.
Replace a fuse by levering the fuse holder cover with an appropriate screwdriver. Remove the old fuse and place
the fuse inside the fuse holder. Replace the fuse holder and insert it back into housing.
Never connect the lighting effect to the mains prior with opened fuse housing.
9. Maintenance & Care instructions
The fixture must be cleaned regularly from dust, other deposits and contamination as this may reduce the
protective insulation, which may lead to a fatal electric shock.
Before cleaning, always disconnect the product from mains.
This product should be cleaned with a moist cloth only. Never use aggressive cleaning agents, solvents or benzene
for cleaning.
10. Technical parameters
Lamp：Single 120W LED
Life：50,000H
Control channels：19 channels
Pan movement：540° (16 bit )
Tilt movement：240° (16 bit )
Advanced Movement System: Fast, precise, and quiet, auto X-Y repositioning
Color wheel：7 dichroic filters +open, half-color and rainbow effect
Fixed gobo wheel：10 fixed gobos + open
Rotating gobo：6 interchangeable, rotating, indexable, gobos + open
Rotating effect wheel：3 facets prism
Focus：Motorized focus
Zoom angle: 7-16°
9

Shutter：Variable from 1-25 flashes or random strobe
Dimmer：0~100% linear dimming
Frost：Fine wash effect
LCD display
N.W.：10KG
G.W.：12KG
Packing size：385*325*475MM
10