ADA INSTRUMENTS ProDigit 30 User manual
ProDigit 30
Manufacturer: ADAINSTRUMENTS Address: WWW.ADAINSTRUMENTS.COM
Operating manual
Digital level
Model: ProDigit 30
MEASUREMENT FOUNDATION
ProDigit 30
Table of contents
1. Safety symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
12. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
13. Exceptions from responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
30
MEASUREMENT FOUNDATION
ProDigit 30
3
Safety symbols
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations
with them, deserve your careful attention and understanding. The symbol warnings DO NOT by themselves eliminate any
danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
WARNING: BE SURE to read and understand all safety instructions in this manual, including all safety alert symbols such
SYMBOL MEANING
-
bols or pictographs.
DAMAGE PREVENTION AND INFORMATION MESSAGES
MEASUREMENT FOUNDATION
ProDigit 30
4
Safety instructions
WARNING: BE SURE to read and understand all instructions in this manual before using this level. Failure to follow all instruc-
SAFETY PRECAUTIONS FOR LASERS
WARNING:
hazardous radiation exposure. WARNING: The use of optical instruments such as, but not limited to, telescopes or transits to
view the laser beam will increase eye hazard.
This level has a built-in laser light. The laser is a Class2 and emits output power of a maximum 1 mW and 635-665 nm wave-
blindness. CAUTION: The following label is on your tool. It indicates level emits the laser light.
BE AWARE of the laser light location. ALWAYS MAKE SURE that any bystanders in the vicinity aware of the dangers of look-
ing directly into the laser. WARNING: LASER RADIATION. DO NOT stare into beam. Class2 laser product.
Only turn laser beam on when the level is on the work surface.
DO NOT remove or deface any product labels. Removing product labels increases the risk of exposure to laser radia-
tion.
could result.
DO NOT place the Digital level in a position that may cause anyone to stare into the laser beam intentionally or uninten-
DO NOT use any magnifying optical tools such as, but not limited to, telescopes or transits to view the laser beam. Seri-
ALWAYS turn the Digital level off when not in use. Leaving the tool on increases the risk of someone inadvertently star-
ing into the laser beam.
1.
2.
3.
4.
5.
6.
7.
8.
30
MEASUREMENT FOUNDATION
ProDigit 30
5
dangerous.
DO NOT place the Digital level in a position that may cause anyone to stare into the laser beam intentionally or uninten-
DO NOT use any magnifying optical tools such as, but not limited to, telescopes or transits to view the laser beam. Seri-
ALWAYS turn the Digital level off when not in use. Leaving the tool on increases the risk of someone inadvertently star-
ing into the laser beam.
dangerous.
DO NOT attempt to modify the performance of this laser device in any way. This may result in a dangerous exposure to
laser radiation.
-
rectly. Match the polarities, positive (+) to positive and negative (-) to negative, as marked inside battery compartment.
DO NOT short battery terminals.
DO NOT mix old and new batteries. If batteries are weak, replace both of them with two new batteries. These new bat-
teries should match each other in brand and type.
Remove dead batteries immediately and dispose of them according to your local ordinance.
Keep batteries out of reach of children. They are not playthings.
Remove batteries and store separately if level will not be used for several days.
10.
11.
12.
13.
14.
15.
16.
17.
18.
20.
21.
22.
23.
24.
MEASUREMENT FOUNDATION
ProDigit 30
6
This digital level is a highly versatile leveling tool designed for fast, easy operation.
Heavy-duty, lightweight aluminum construction, with the LCD digital module constructed of unbreakable ABS polymer that’s
sealed against dirt and water, and the toughest acrylic block bubble vials and solid-state laser components all add up to on-
-
age slopes.
Use the laser beam to extend a visual leveling line over distances much greater than a traditional bubble vial beam level.
Use the level manually, hand held, or mounted on a tripod (sold separately).
Use the digital level inside or outside to measure pitch in inches of rise per foot of run.
Measure in degrees with up to 0.05° accuracy.
Measure any slope in percent...measure level and plumb with either the LCD digital display or with the vertical and horizontal
bubble vials.
Features (Fig.1a)
Keyboard
LCD Display - Large, easy-to-read display screen reads right side up even when level is upside down.
Bubble Vials- The level or plumb of a surface can also be accurately measured by positioning the bubble inside the vial
Integrated 57cm Ruler
Endcaps - Ends cushioned to help protect level from damage.
Laser Light Aperture - The laser beam is emitted from this opening, which is on the end cap of the level.
Magnetic Bottom -Four magnets in the working base allow for secure contact to metal, handy when working with steel
studs or metal ductwork.
1.
2.
3.
4.
5.
6.
7.
8.
30
MEASUREMENT FOUNDATION
ProDigit 30
7
Fig.1a
Large, Soft-grip Handles - For ease in carrying, holding level in place.
10.
11.
12.
MEASUREMENT FOUNDATION
ProDigit 30
8
Key function (Fig.1b)
Power button -press the button to turn the LCD display screen on. Long press it to turn off the LCD display.
REF Button
button for about 3 seconds to start the calibration.
Sound On/Off Button - Used to activate the beeper. When button is pushed, beeper sounds at level (0°), 45°,
M Button - Push to save the current reading in its memory. The level will save last nine different consecutive angle read-
ings in its memory.
MR Button
UNIT Button - By pushing this button you can convert angles to different units. Push to change the display units from
indicate that the pitch is slightly more (+) or less (-) than true level.
1.
2.
3.
4.
5.
6.
30
MEASUREMENT FOUNDATION
ProDigit 30
LCD SCREEN ICONS
either up or down away from the level (0°).
Battery Power Icon - Indicates the amount of battery power in the unit. Replace batteries when the black power bar
dis appears.
measurements.
REF Indicates that the level is working in relative angle mode.
Err Indicates that the level is wrong positioned or wrong operation in calibration.
CAL1 Indicates that the digital level is in calibrating for one direction.
CAL2 Indicates that the digital level is in calibrating for the another direction.
0
Recommended use Indoors or Outdoors
Laser class Class2, max laser output ≤1mW
Power supply 2x 1.5V AAA battteries
Angle measuring range 0 to 360°
Optimum operation range 0 to 40°
Accuracy of vials ±0.029°
Accuracy of digital display ±0.05°(level or plumb)
±0.1°(other angles)
Estimated Battery life 10 hours with alkaline batteries
MEASUREMENT FOUNDATION
ProDigit 30
10
Battery installation (Fig. 2)
and the Laser dot.
Fig.2
NOTE
Open the battery cover, located in the middle of the back of the level (Fig.2).
Close the cover securely in place.
Turn on the LCD display
in centigrade for about 2 seconds, to indicate if level is being used in optimum operating temperature range. The current
angle of the level is then displayed, and a picture of that angle is shown either above or below the line for true level.
An arrow on the display indicates if the level has to be moved up or down. True level is reached when the two lines are
together and the angle shows 0.00°. Turn off the LCD display by pressing and holding the button in for about 2 seconds.
If the digital level is not used for 5 minutes the level automatically turns off. The LCD display is large and easy to read.
When the level is turned upside down, the LCD screen senses and changes to read correctly in the inverted position.
1.
2.
3.
30
MEASUREMENT FOUNDATION
ProDigit 30
11
Calibration (Figs.3,4)
the beeper will sound for 2 seconds to tell calibrating completed, the LCD will show the current angle in high-accuracy-dis-
play.
Fig.3 Fig.4
Important NOTE:
The digital level has been pre-calibrated to high-accuracy-display mode. It possibly runs to rough-accuracy-display
mode if the temperature changes too much. Suggest calibrating the digital level every time before you use it.
To ensure an accurate measurement, the calibration should be performed separately for horizontal measurement,
plumb measurement or upside measurement.
In the calibration, the level also can not be beveled or moved, same Err will occur with the wrong operation.
CAL2, the digital display will wrongly set the current working surface as 0°, it will recover to normal function after a
correct calibration.
within 1º. If the gradient exceeds 1º, LCD will recover to rough accuracy display.
•
•
•
•
•
•
MEASUREMENT FOUNDATION
ProDigit 30
12
Measurements
Horizontal and Plumb measurements can use both the bubble vial and the LCD readout features.
Horizontal measurements (Fig.5)
Use the level on horizontal surfaces to true them up. The level’s bubble vials will show when you have the surface level. The
bubbles will be exactly in between the marks on the vial.
Once the Power button is turned on, lay the level on the surface you want to level. The LCD display will show the surface you
are measuring as a line either above or below the true level line, and the degree to which the surface is off, with an arrow
showing whether the surface should be raised or lowered in order to be leveled.
Fig.5
The LCD display also gives the degree to which the surface is off. To level, move the surface with the level on
it until the two lines on the readout match and the readout says 0.00° for the angle. If the beeper is activated,
the beeper will sound when the level is at level.
Vertical measurements (Fig.6)
vial at the top. The surface will be at true plumb when the bubble is positioned exactly between the marks on
the vial.
The LCD display shows the surface with the level on it as a line, and true plumb as another line either to the
left or right of the line for plumb, and the degree to with the surface is off, with an arrow showing whether to
is reached. Fig.6
30
MEASUREMENT FOUNDATION
ProDigit 30
13
Pitch (Fig.7)
The digital level can be used to measure the pitch of a roof. It measures the pitch in
inches of rise per foot of run. Push the conversion button to change angle to pitch. The
if the pitch is above or below the desired measurement.
Angle (Fig.8)
The digital level measures any angle in degrees with up to 0.1° accuracy, at level or
angle for many surfaces, and when the conversion button is pushed to display angle,
will tell you the angle and which way it is off of true level. If the beeper button is turned
on, the level will beep at 0.00° angle.
Slope (Fig.9)
The digital level measures the slope of a surface in percent. This is useful when lay-
ing pipe for proper drainage. When the conversion button is in the slope mode, it will
Fig.7
Fig.8
MEASUREMENT FOUNDATION
ProDigit 30
14
Laser alignment (Fig.10)
This digital level contains a laser diode located inside the left endcap
of the level. It provides a bright 635-665 nanometer beam with a useful
visibility that extends up to 50m indoors or outdoors (This range is only
applicable at night or dark environment.)
on the right endcap of the level
The center of the laser beam is 30mm above the bottom (working)
surface of the level.
Remember to account for this when doing layouts and taking mea-
surements.
away to enable you to level large areas.
and shape may change slightly with distance, temperature or target
surface material. The point to use is the center of the dot pattern.
Operation with tripod (Figs.11,12 and 13)
(see Fig. 11).
at 0.00° on the LCD display screen and, if activated, the beeper will beep.
•
•
•
•
•
•
•
•
•
Fig.10
30
MEASUREMENT FOUNDATION
ProDigit 30
Fig.12
Fig.11
15
-
ture, distance and target surface material. ALWAYS use the center point of the dot for your measurement. Rotate the
level on the tripod to align chair rail, pictures, etc. 360° around the space.
•
Fig.13
MEASUREMENT FOUNDATION
ProDigit 30
16
Current reading memorize button and memory recall
To save the information of the current reading, press the M button. The level can save nine different readings in its memory.
To read out the measurements, press the MR button. The last nine measurements can be read out, beginning with the most
recently saved. To make a new measurement, press the M button to return to measuring mode.
Using conversion button to change display units
level shown on the display. The conversion button can be used even when the display is in the MR mode. This feature is a
to 22.6° for setting up cuts on a chop saw.
Absolute angle and relative angle measurements
Absolute angle measurement
indicates the level position, and the arrow indicates the direction of the working surface either above or below level.
last saved angle. To deactivate beeper, push button a second time.
To save the measured angle in memory, press the M button. This level can remember the last nine measurements. To dis-
play the data in memory, press the memory recall button to recall recorded angles. The level will read out the data starting
with the most recent measurements and going backwards to the earliest in its memory.
To take a new measurement, press the hold button to return to measurement mode.
Relative angle measurement
Lay the digital level on the First working surface.
30
MEASUREMENT FOUNDATION
ProDigit 30
17
Turn on the level. The LCD screen indicates the absolute angle between true level and the working surface.
Press the REF button to enter relative angle measurement mode. The current angle will be considered to be 0.0° and the
display will read 0.0°.
Place the digital level on the Second working surface and the relative angle between the First working surface and the
Second working surface will be displayed. The zero line indicates the First working surface position, and the arrow indicates
the direction
of the Second working surface either above or below the First working surface level.
pressing the conversion button.
Maintenance
This digital laser level has been designed to be a low-maintenance tool. However, in order to maintain its performance,
follow these steps.
HANDLE the tool with care. Treat it as a precision optical device, such as a camera or binoculars.
11. AVOID exposing the tool to shock, continuous vibration or extreme hot or cold temperatures.
STORE the tool indoors and in a safe place.
The Level is designed to be weather resistant and construction site tough. If the level is splashed with mortar or other
construction site residue, simply wipe clean with a damp cloth. DO NOT immerse the level in water.
Aluminum surfaces can be cleaned with a non-abrasive powder.
Check the batteries regularly to avoid corrosion. REMOVE the batteries from the tool if it is not going to be used for
an extended period.
DO NOT try to take the level apart.
•
•
•
•
•
•
•
MEASUREMENT FOUNDATION
ProDigit 30
18
Troubleshooting
Problem Cause Solution
Laser point projection is
weak
Batteries are low voltage. Replace with new batteries
Laser point is not projected •Laser on/off button is not in
ON position.
•Batteries are installed
incorrectly.
•Battery power is low.
•Laser diode is damaged
•Check to make sure the switch
is in On position.
•Re-install batteries with correct
polarity.
•Replace with new batteries
•Take tool to the service center.
The LCD screen can not be
turned on
•Batteries are installed
incorrectly.
•Batteries voltage is low
•The LCD screen is damaged
•Re-install batteries with correct
polarity
•Replace with new batteries.
•Take tool to the service center.
dot line displayed on screen
instead of angle, slope or
pitch
The di g i t a l le v el i s be v e l
positioned with the working
surface.
Make sure the digital level is
positioned plumb to the working
surface.
Err occurs on LCD during
calibration
•The gradient of the working
surface for calibration exceeds
5 degree
•The digital le ve l is b ev el
positioned with the working
surface.
•The digital level is moved
during the calibration
•Make sure the digital level is
positioned on a level surface
w i t h g r a d i e n t l e s s t h a n 5
degree.
•Make sure the digital level is
positioned plumb to the working
surface
•Keep the level unmoved during
calibration.
Wrong setting the current
angle to 0.00°
The digital level is not rotate
180° before starting CAL2
during the calibration.
Re-calibrate the digital level with
a right procedure.
30
MEASUREMENT FOUNDATION
ProDigit 30
Measurements through glass or plastic windows.
Dirty laser emitting window.
After instrument has been dropped or hit. Please check the accuracy.
other way round) please wait some minutes before carrying out measurements.
Electromagnetic acceptability (EMC)
It cannot be completely excluded that this instrument will disturb other instruments (e.g. navigation systems);
will be disturbed by other instruments (e.g. intensive electromagnetic radiation nearby industrial facilities or radio trans-
mitters).
•
•
•
•
•
•
MEASUREMENT FOUNDATION
ProDigit 30
The instrument is a laser class 2 laser product accortding to DIN IEC 60825-1:2007. It is allowed to use unit without
further safety precautions.
Warranty
This product is warranted by the manufacturer to the original purchaser to be free from defects in material and work-
manship under normal use for a period of two (2) years from the date of purchase.
During the warranty period, and upon proof of purchase, the product will be repaired or replaced (with the same or
similar model at manufactures option), without charge for either parts of labour.
In case of a defect please contact the dealer where you originally purchased this product. The warranty will not apply
to this product if it has been misused, abused or altered. Withiut limiting the foregoing, leakage of the battery, bending
or dropping the unit are presumed to be defects resulting from misuse or abuse.
20
Other manuals for ProDigit 30
1
Table of contents
Other ADA INSTRUMENTS Laser Level manuals
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE 2-360 User manual
ADA INSTRUMENTS
ADA INSTRUMENTS ProDigit Mini User manual
ADA INSTRUMENTS
ADA INSTRUMENTS 2D Basic Level User manual
ADA INSTRUMENTS
ADA INSTRUMENTS 2D Basic Level User manual
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE 2-360 GREEN User manual
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE 360-2V GREEN User manual
ADA INSTRUMENTS
ADA INSTRUMENTS 6D MAXLINER User manual
ADA INSTRUMENTS
ADA INSTRUMENTS ARMO 2D User manual
ADA INSTRUMENTS
ADA INSTRUMENTS ROTARY 400 HV Servo User manual
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE User manual
ADA INSTRUMENTS
ADA INSTRUMENTS 3D Liner 2V Green User manual
ADA INSTRUMENTS
ADA INSTRUMENTS BASIS User manual
ADA INSTRUMENTS
ADA INSTRUMENTS ROTARY 500 HV SERVO User manual
ADA INSTRUMENTS
ADA INSTRUMENTS TOPLINER 3-360 GREEN User manual
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE MINI User manual
ADA INSTRUMENTS
ADA INSTRUMENTS 5D CROSSPOINT User manual
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE MINI GREEN User manual
ADA INSTRUMENTS
ADA INSTRUMENTS ProDigit 30 User manual
ADA INSTRUMENTS
ADA INSTRUMENTS 6D SERVOLINER GREEN User manual
ADA INSTRUMENTS
ADA INSTRUMENTS 3D Liner 2V Green User manual
