ADA INSTRUMENTS 3D Liner 2V Green User manual

Line Laser
OPERATING MANUAL
3D Liner 2V / 4V Green
adainstruments.com

2English
1
2
34
56
7
1
6
2
3
4
5
1
5
6
3
4
2
2V
4V

3
THE MANUFACTURE RESERVES THE RIGHT TO MAKE CHANGES (NOT
HAVING AN IMPACT ON THE SPECIFICATIONS) TO THE DESIGN,
COMPLETE SET WITHOUT GIVING PRIOR WARNING.
APPLICATION
Line laser ADA 3D LINER 2V/4V GREEN is designed to check the horizontal
and vertical position of the surfaces of the elements of building structures
and also to transfer the angle of inclination of the structural part to similar
parts during construction and installation works.
SPECIFICATIONS
Laser beam ..........................................2V/4V1H1D
Light sources ...................................... 532nm/floor point 650nm
Laser safety class .............................. Class 2, <1mW
Accuracy .............................................. ±0.2mm/1m
Self-leveling range ............................ ±3°
Operating range
with/without receiver ...................... 70/40 m
Power source ...................................... Li-ion batteery 3.7 V 3200 mАh /
4 AA batteries / charger
Rotation/Fine adjustment ...............360°
Tripod thread ...................................... 5/8”
Operating temperature ................... -10°C +40°C
FUNCTIONAL DESCRIPTION
1. 2 or 4 vertical lines (the quantity of lines depends on the model of the
English

4English
instrument), 1 horizontal line, plumb down.
2. Can be used both for operation indoor and outdoor. Use the receiver
for outdoor operation up to 70 m.
3. Electronic compensator ensures quicker self-leveling within range
±3° .
4. When the instrument inclines more than ±3° the laser lines
automatically gleam.
5. 360° rotating ne adjustment mechanism makes it easier to
aim the vertical beam.
6. When turning o the power, built-in locking system can automatically
lock the compensator to avoid vibration during the transportation.
FEATURES
1. Carrying handle
2. Vertical laser window
3. Horizontal laser window
4. Fine adjustment
5. Adjusting legs
6. Power switch
OPERATION
1. Take out the battery lid. According the sign “ + ,- ”, insert four alka-
line batteries or rechargeable battery to the battery socket, then cover the
battery lid. Remove batteries, if you are not going to use the tool for a long
period of time.
2. It is also possible to use the charger for the operation with the tool.
Use the charger to charge the rechargeable batteries. Connect the charger
KEYPAD
1. Indoor/outdoor key (D)
2. Power LED
3. H laser lines switch
4. Bubble level
5. V laser lines switch
6. Detector LED
34

5English
to the plug that is located on the housing of the tool. And then connect
it to mains. The tool will operate and charge the rechargeable batteries.
Note! Never connect the charger if you use ordinary batteries. Never
leave the tool unattended when connecting the charger. Characteris-
tics of the charger must correspond to the characteristics of mains.
Output voltage must be no more than 5V.
3. Set up the line laser on the oor or the tripod. When using tripod, put
the bottom part of the instrument on the tripod. Twist in the screw of the
tripod into the centering nut of the instrument.
4. Switch ON the tool mooving the power switch (6) to the “ON” position.
During transportation always set the power switch (6) to the position “OFF”.
If laser lines are blinking, it means that the inclination of the line laser
is more than ±3°. Adjust the line laser with the help of the tool’s legs or
tripod.
5. Aim the down point on the selected point on the oor. Move the upper
part of the instrument to adjust vertical lines. Use ne adjustment
mechanism for accurate adjustment of the instrument.
6. The tool has several operating modes. Use “H” and “V” buttons to select
the necessary mode. “H” button switches On/O the horizontal line. “V”
button switches On/O the vertical lines and plumb down:
- for 3D Liner 2V Green - 1V 1D/ 2V 1D
- for 3D Liner 4V Green - 1V 1D/ 2V 1D /4V 1D
7. Press once button (1). LED (6) is ON. Line laser is in the “outdoor” mode.
Press button (1) once again. LED (6) is OFF. Line laser starts to operate in
“indoor” mode. Use the detector to operate in this mode (see operating
manual for the detector).

6English
TO CHECK THE ACCURACY
Set up the instrument between two walls, the distance is 5 m.Turn on the
line laser and mark the point of cross laser line on the wall. Set up the in-
strument 0,5-0,7m away from the wall and make, as described above, the
same marks. If the dierence {a1-b2} and {b1-b2} is less than the value of
“accuracy” (see spesications), there is no need in calibration.
Example: when you check the accuracy of line laser the dierence is {a1-
a2}=5 mm and {b1-b2}=7 mm. The instrument’s error: {b1-b2} {a1-a2}=7-
5=2 mm.
Now you can compare this error with standard error. If the accuracy of Line
Laser isn’t corresponding with claimed accuracy, contact the authorized
service center.
TO CHECK THE ACCURACY OF HORIZONTAL BEAM
Choose a wall and set laser 5M away from the wall. Turn on the laser and
cross laser line is marked A on the wall.Find another point M on the hori-
zontal line, the distance is around 2.5m. Swivel the laser, and another cross
point of cross laser line is marked B.
Please note the distance of B to A should be 5m. Measure the distance
between M to cross laser lune, if the dierence is over 3mm, the laser is out
of calibration, please contact with seller to calibrate the laser.
TO CHECK PLUMB
Choose a wall and set laser 5m away from the wall. Mark point A on the
wall, please note the distance from point A to ground should be 3m. Hang
a plumb line from A point to ground and nd a plumb point B on ground.
turn on the laser and make the vertical laser line meet the point B, along
6
5

7English
the vertical laser line on the wall and measure the distance 3m from point
B to another point C. Point C must be on the vertical laser line, it means the
height of C point is 3m.
Measure the distance from point A to point C, if the distance is over 2 mm,
please, contact with seller to calibrate the laser.
PRODUCT LIFE
Product life of the tool is 7 years. The battery and the tool should never
be placed in municipal waste. Date of production, manufacturer’s contact
information, country of origin are indicated on the product sticker.
CARE AND CLEANING
Please handle line laser with care. Clean with soft cloth only after any use.
If necessary damp cloth with some water. If instrument is wet clean and
dry it carefully. Pack it up only if it is perfectly dry. Transport in original
container/case only.
Note: During transport On/O compensator lock (5) must be set to posi-
tion “OFF”. Disregard may lead to damage of compensator.
SPECIFIC REASONS FOR ERRONEOUS MEASURING RESULTS
• Measurements through glass or plastic windows;
• Dirty laser emitting window;
• After line laser has been dropped or hit. Please check the accuracy;
• Large uctuation of temperature: if instrument will beused in cold areas
after it has been stored in warm areas (or the other way round) please wait
some minutes before carrying out measurements.

8English
ELECTROMAGNETIC ACCEPTABILITY (EMC)
• It cannot be completely excluded that this instrument will disturb other
instruments (e.g. navigation systems);
• will be disturbed by other instruments (e.g. intensive electromagnet-
ic radiation nearby industrial facilities or radio transmitters).
LASER CLASS 2 WARNING LABELS ON THE LASER INSTRUMENT
LASER CLASSIFICATION
The instrument is a laser class 2 laser product accortding to DIN IEC 60825-
1:2014. It is allowed to use unit without further safety precautions.
SAFETY INSTRUCTIONS
• Please follow up instructions given in operators’ manual.
• Do not stare into beam. Laser beam can lead to eye injury (even from
greater distances).
• Do not aim laser beam at persons or animals. The laser plane should
be set up above eye level of persons. Use the instrument for measuring
jobs only.
• Do not open instrument housing. Repairs should be carried out by au-
thorized workshops only. Please contact your local dealer.
• Do not remove warning labels or safety instructions.
• Keep instrument away from children.
• Do not use instrument in explosive environment.
WARRANTY
This product is warranted by the manufacturer to the original purchaser to
7

9
English
be free from defects in material and workmanship under normal use for a
period of two (2) years from the date of purchase. During the warranty pe-
riod, and upon proof of purchase, the product will be repaired or replaced
(with the same or similar model at manufactures option), without charge
for either parts of labour.
In case of a defect please contact the dealer where you originally pur-
chased this product. The warranty will not apply to this product if it has
been misused, abused or altered. Without limiting the foregoing, leakage
of the battery, bending or dropping the unit are presumed to be defects
resulting from misuse or abuse.
EXCEPTIONS FROM RESPONSIBILITY
The user of this product is expected to follow the instructions given in op-
erators’ manual. Although all instruments left our warehouse in perfect
condition and adjustment the user is expected to carry out periodic checks
of the product’s accuracy and general performance.
The manufacturer, or its representatives, assumes no responsibility of re-
sults of a faulty or intentional usage or misuse including any direct, indi-
rect, consequential damage, and loss of prots.
The manufacturer, or its representatives, assumes no responsibility for
consequential damage, and loss of prots by any disaster (earthquake,
storm, ood ...), re, accident, or an act of a third party and/or a usage in
other than usual conditions.
The manufacturer, or its representatives, assumes no responsibility for
any damage, and loss of prots due to a change of data, loss of data and
interruption of business etc., caused by using the product or an unusable
product.
The manufacturer, or its representatives, assumes no responsibility for
any damage, and loss of prots caused by usage other thsn explained in
the users’ manual.
The manufacturer, or its representatives, assumes no responsibility for
damage caused by wrong movement or action due to connecting with oth-
er products.

10
WARRANTY DOESN’T EXTEND TO FOLLOWING CASES:
1. If the standard or serial product number will be changed, erased, re-
moved or wil be unreadable.
2. Periodic maintenance, repair or changing parts as a result of their nor-
mal runout.
3. All adaptations and modications with the purpose of improvement
and expansion of normal sphere of product application, mentioned in the
service instruction, without tentative written agreement of the expert pro-
vider.
4. Service by anyone other than an authorized service center.
5. Damage to products or parts caused by misuse, including, without lim-
itation, misapplication or nrgligence of the terms of service instruction.
6. Power supply units, chargers, accessories, wearing parts.
7. Products, damaged from mishandling, faulty adjustment, maintenance
with low-quality and non-standard materials, presence of any liquids and
foreign objects inside the product.
8. Acts of God and/or actions of third persons.
9. In case of unwarranted repair till the end of warranty period because
of damages during the operation of the product, it’s transportation and
storing, warranty doesn’t resume.

11
WARRANTY CARD
Name and model of the product __________________________________________
Serial number___________________________Date of sale______________________
Name of commercial organization ________________________________________
stamp of commercial organization
Warranty period for the instrument explotation is 24 months after the
date of original retail purchase.
During this warranty period the owner of the product has the right for
free repair of his instrument in case of manufacturing defects.
Warranty is valid only with original warranty card, fully and clear lled
(stamp or mark of thr seller is obligatory).
Technical examination of instruments for fault identication which is
under the warranty, is made only in the authorized service center.
In no event shall manufacturer be liable before the client for direct or
consequential damages, loss of prot or any other damage which occur
in the result of the instrument outage.
The product is received in the state of operability, without any visible
damages, in full completeness. It is tested in my presence. I have no
complaints to the product quality. I am familiar with the conditions of
qarranty service and i agree.
purchaser signature _______________________________
Before operating you should read service instruction!
If you have any questions about the warranty service and technical support contact
seller of this product

adainstruments.com
ADA International Group Ltd., No.6 Building, Hanjiang West Road #128,
Changzhou New District, Jiangsu, China
Made In China