ADA INSTRUMENTS TOPLINER 3-360 User manual

MEASUREMENT FOUNDATION
Operating manual
Laser level
TOPLINER 3-360 GREEN

2
1. Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Technical requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Safety requirements and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4. Order working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
6. Safety precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
8. Exceptions from responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Appendix 1- “Warranty card”
Table of contents

3
1. CAUTIONS
Laser level ADA TOPLINER 3-360 GREEN is an up-to-date functional and multi-prism device designed for indoor
and outdoor performance. The device emits:
one horizontal laser line (beam scan angle of 360°)
two vertical laser lines (beam scan angle of 360°)
Do not look at the laser beam!
Do not install the device on the eye level!
Before using the device, do read this operating manual!
2. TECHNICAL REQUIREMENTS
2.1. FUNCTIONAL DESCRIPTION
Emitting a horizontal and two vertical laser line.
Quick self-leveling: when line accuracy is out of the range the laser line
ashes and the warning sound is produced. Compensator locking system
for safe transportation. Intermediate compensator locking system for slope operation.
Indoor and outdoor performance function.
360 eVercal Line
360 eVercal Line
360 eHorizontal Line

4
1. Keypad
2. Jack for charger
3. Battery compartment
4. Rotating base
5. Lock switch
(ON/X/OFF)
6. Vertical laser window
7. Horizontal laser window
2.2. FEATURES 1
2
3
5
4
6
7

5
Button panel
Tilt LED (1)
Indicator lights up in the intermediate position of the
compensator lock.
Detector LED (2)
Indicator lights up when press Detector button.
Power LED (3)
Indicator lights up when power is on.
Indicator blinks when power is low.
Horizontal switch (H) (4)
Detector switch (5)
Vertical switch (V) (6)
2
3
4
5
6
1

6
2.3. SPECIFICATIONS
Laser 2V1H (360° laser)
Light sources 532nm
Laser safety class Class 2, <1mW
Accuracy ±3 mm/10 m
Self-leveling range ±4.5°
Operating range with/without receiver radius 40~70m (with detector)
Rotation/Fine adjustment 360 °/ ±10° (with Rotation base)
Power source Li battery set
Operation time Approx. 5-8 hours, if everything is on
Tripod thread 1/4 ″ and 5/8 ″
Operating temperature -10°C +40°C
Weight 0.9 kg (with Rotation base)
Size 130mm ×60mm ×160 mm (with Rotation base )

7
3. SAFETY REQUIREMENTS AND CARE
Follow safety requirements! Don’t face and stare at laser beam!
Laser level is an accurate Instrument, which should be stored and used with care.
Avoid shaking and vibrations! Store the Instrument and It’s accessories only In the carrying case.
In case of high humidity and low temperature, dry out the Instrument and clean It after the usage.
Do not store the Instrument at a temperature below -20°C and above 50°C, otherwise the Instrument can be
out of action.
Don’t put the Instrument Into the carrying case If the Instrument or case are wet. To avoid moisture condensa-
tion Inside the Instrument- dry out the case and laser Instrument!
Check regularly Instrument adjustment!
Keep the lens clean and dry. To clean the Instrument use a soft cotton napkin!
Do not aim laser beam at persons or animals.
Do not open instrument housing. Repairs should be carried out by authorized workshops only.
Do not remove warning labels or safety instructions.
Keep instrument away from children.
Do not use instrument in explosive environment.

8
4. ORDER WORKING
Assemblage of the rotating base
Remove the instrument from the base (Picture 1).
Place the instrument on the base (Picture 2).
Picture 2Picture 1

9
Insert the battery (Picture 3)
Use standard Li-battery only.
Pay attention to the polarity.
Insert the battery.
Cover the battery cover.
Li-battery
Battery cover
Picture 3

10
Picture 5 Picture 4
Mounting thread
It is possible to place the instrument on the tripod or wall mount during operation. For attachement use
thread 1/4” (pic.4) at the bottom part of the instrument or thread 5/8” (pic. 5) at the bootom part of the
rotating base.

11
Lock Switch
Lock switch has tree positions:
OFF mode (Pic.6)
Power is OFF. Pendulum is locked. Button panel can
not be used.
Tilt mode (Pic.7)
Power is ON. Pendulum is locked. Button panel can be used.
Vertical lines and horizontal line can be switched on/off.
ON mode (Pic.8)
Power is on. Pendulum is unlocked. Self-leveling.
Button panel can be used. Vertical lines and horizontal line can be
switched on/off. Detector mode.
Рic. 6
Рic. 7
Рic. 8

12
Picture 9
Picture 10
Power warning (Picture 9)
Power LED ashes when the power is full.
Maximum operating time with all laser beams is about 30
min. All laser beams and LED will be shut off when the power
is very low. Please use the standard charger to charge the
instrument.
Charger LED (10)
The LED of the charger will be yellow when it’s charging.
When power is full, the indicator changes into green light.
The Charger should be 5V 1A . The instrument can be used
while charging.

13
Picture 11
Tilt mode warning
The instrument can work in the tilt mode (intermediate position of lock switch).
Tilt LED ashes (Pic.11). Pendulum is locked. Laser lines are projected at any
angle. For example, when making stairs.
Detector mode (рic. 12)
Use the detector mode in bright light when laser beam is not visible. Press button
to switch on the dector mode. Upper LED ashes. Place the detector to
the the place of beam location. Follow the instruction of detector usage when
searching the beam.
Out of leveling warning
All the laser beams will be shut off when the instrument is out of leveling range.
The buzzer will alarm at the same time.
Transportation
Please turn the lock switch in OFF mode.
Please put the instrument on the correct position in soft bag or case.
Dot not drop it during transportation.

14
Picture 12 Picture 13
Usage of rotating base
360 °rotating (Picture 12)
Part A can rotate around part B by 360°.
±10° ne adjustment (Picture 13)
In leveling mode, by using adjusting
knob , the instrument can rotate
around the down dot by ± 10°.

15
To check the accuracy of line laser level
To check the accuracy of line laser level
(slope of plane)
Place laser level on the tripod 5m away from the
wall so the horizontal laser line will be directed
to the wall.
Switch on the power. The instrument starts to
self-level. Mark point A on the wall to show the con-
tact of laser beam with the wall. Turn the instrument
by 90° and mark points В, С, D on the wall. Measure
distance “h” between the highest and lowest points
(these are A and D points in the picture).
If “h” is ≤ 6 mm, the measurement accuracy is
good. If “h” exceeds 6 mm, apply service center.

16
To check plumb
Choose a wall and set laser 5 m away from the wall. Hang a plumb with the length 2.5 m on the
wall. Turn on the laser and make the vertical laser line meet the point of the plumb. The accuracy
of the line is in the range if the vertical line doesn’t exceed (up or down) the accuracy that is shown
in the specifications (e.g. ±3 mm/10 m). If the accuracy isn’t corresponding with claimed accuracy,
contact the authorized service center.

17
5. APPLICATION
6. SAFETY PRECAUTION
near emitter.

18
CARE AND CLEANING
Please handle measuring instrument with care. Clean with soft cloth only after any use. If necessary damp cloth with some
water. If instrument is wet clean and dry it carefully. Pack it up only if it is perfectly dry. Transport in original container/case only.
Note: During transport On/Off compensator lock (5) must be set to position “OFF”. Disregard may lead to damage of compen-
sator.
SPECIFIC REASONS FOR ERRONEOUS MEASURING RESULTS
• Measurements through glass or plastic windows;
• Dirty laser emitting window;
• After instrument has been dropped or hit. Please check the accuracy.
• Large uctuation of temperature: if instrument will be used in cold areas after it has been stored in warm areas (or the
other way round) please wait some minutes before carrying out measurements.
ELECTROMAGNETIC ACCEPTABILITY (EMC)
• It cannot be completely excluded that this instrument will disturb other instruments (e.g. navigation systems);
• will be disturbed by other instruments (e.g. intensive electromagnetic radiation nearby industrial facilities or radio trans-
mitters).

19
LASER CLASSIFICATION
The instrument is a laser class 2 laser product accortding to DIN IEC 60825-1:2007. It is allowed to use unit without further
safety precautions.
Note: Because of construction of laser emitter laser beam may be unhomogeneous and has different intensity of
brightness along the perimeter in different light conditions. Unhomogeneous of laser beam: laser patch of light but the
center of laser beam is identied. Different laser beam brightness: difference of intensity is up to 50%.
WARRANTY
This product is warranted by the manufacturer to the original purchaser to be free from defects in material and workmanship
under normal use for a period of two (2) years from the date of purchase.
During the warranty period, and upon proof of purchase, the product will be repaired or replaced (with the same or similar
model at manufactures option), without charge for either parts of labour.
In case of a defect please contact the dealer where you originally purchased this product. The warranty will not apply to this
product if it has been misused, abused or altered. Withiut limiting the foregoing, leakage of the battery, bending or dropping the
unit are presumed to be defects resulting from misuse or abuse.

20
EXCEPTIONS FROM RESPONSIBILITY
The user of this product is expected to follow the instructions given in operators’ manual.
Although all instruments left our warehouse in perfect condition and adjustment the user is expected to carry out periodic
checks of the product’s accuracy and general performance.
The manufacturer, or its representatives, assumes no responsibility of results of a faulty or intentional usage or misuse includ-
ing any direct, indirect, consequential damage, and loss of prots.
The manufacturer, or its representatives, assumes no responsibility for consequential damage, and loss of prots by any
disaster (earthquake, storm, ood ...), re, accident, or an act of a third party and/or a usage in other than usual conditions.
The manufacturer, or its representatives, assumes no responsibility for any damage, and loss of prots due to a change of
data, loss of data and interruption of business etc., caused by using the product or an unusable product.
The manufacturer, or its representatives, assumes no responsibility for any damage, and loss of prots caused by usage other
thsn explained in the users’ manual.
The manufacturer, or its representatives, assumes no responsibility for damage caused by wrong movement or action due to
connecting with other products.