Adamson IS7px User manual

Adamson Systems Engineering |
Table of Contents
Read these instructions, keep them available for reference.
This manual can be downloaded from
Heed all warnings and follow all instructions.
A qualifi ed technician must be present during the installation and use of this product. This product
is capable of producing extremely high sound pressure levels and should be used according to the
specifi ed local sound level regulations and good judgement. Adamson Systems Engineering will
not be liable for damages caused by any possible misuse of this product.
Servicing is required when the loudspeaker has been damaged in any way, such as when the
loudspeaker has been dropped; or when for undetermined reasons the loudspeaker does not
operate normally. Inspect your products regularly for any visual or functionality irregularities.
Protect the cabling from being walked on or pinched.
Read the appropriate IS-Series Rigging Manual before installing the product.
Pay attention to rigging instructions included in both Blueprint AV™ and the IS-Series Rigging
Manual.
Use only with the rigging frames/accessories specifi ed by Adamson, or sold with the loudspeaker
system.
This speaker enclosure is capable of creating a strong magnetic fi eld. Please use caution around
the enclosure with data storage devices such as hard drives.
Safety & Warnings
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
3
4
5
6
7
8
9
In an effort to continuously improve its products, Adamson releases
updated accompanying software, presets and standards for its products.
Adamson reserves the right to change the specifications of its
products and the content of its documents with no prior notice.
Page 1
IS7px User Manual

Distribution Date: May 1st, 2021
Copyright 2021 by Adamson Systems Engineering Inc.; all rights reserved
This manual must be accessible to the person operating this product. As such, the product owner must store it in a safe
place and make it available upon request to any operator.
Resale of this product must include a copy of this manual.
This manual can be downloaded from
Declarations
EU Declaration of Conformity
Adamson Systems Engineering declares that the
products stated below are in conformance with the
relevant fundamental health and safety criteria of the
applicable EC Directive(s), in particular:
Signed at Port Perry, ON. CA - May 1st, 2021
------------------------------------------------
Brock Adamson (President & CEO)
ADAMSON SYSTEMS ENGINEERING, Inc.
1401 Scugog Line 6, Port Perry (ON), L9L 1B2, Ontario,
Canada
T: [phone], F: [phone]
Email: [email protected]
Website: www.adamsonsystems.com
IS7px User Manual
Directive 2014/35/EU: Low Voltage Directive
IS7px - 70 x 40 - 967-0006, 967-0007, 967-0015,
967-5006, 967-5007, 967-5015
IS7px - 100 x 50 - 967-0009, 967-0010, 967-0016,
967-5009, 967-5010, 967-5016
Directive 2006/42/EC: Machinery Directive
IS7p & IS10p Fill Plate - 930-0031, 930-5031
IS7p Short Fill Plate - 930-0032
IS7p Horizontal Bracket - 934-0027, 934-5027
IS7p Vertical Bracket - 934-0028, 934-5028
IS-Series Sight Mount - 934-0026, 934-5026
Bracket C-Clamp - 932-0006, 932-5006
IS-Series Pole Mount Adapter - 932-0039
IS-Series C-Clamp - 932-0040
IS-Series Point H-Clamp - 932-0041
IS-Series Tilt Adapter - 932-0042
IS-Series Sight Mount LInk - 932-0044
IS-Series Super Sight Mount - 934-0031
IS-Series Articulator - 934-0032, 934-5032
https://www.adamsonsystems.com/en/support/downloads-directory/is-series/is7px

Adamson Systems Engineering |
Table of Contents
Read these instructions, keep them available for reference.
This manual can be downloaded from
Heed all warnings and follow all instructions.
A qualifi ed technician must be present during the installation and use of this product. This product
is capable of producing extremely high sound pressure levels and should be used according to the
specifi ed local sound level regulations and good judgement. Adamson Systems Engineering will
not be liable for damages caused by any possible misuse of this product.
Servicing is required when the loudspeaker has been damaged in any way, such as when the
loudspeaker has been dropped; or when for undetermined reasons the loudspeaker does not
operate normally. Inspect your products regularly for any visual or functionality irregularities.
Protect the cabling from being walked on or pinched.
Read the appropriate IS-Series Rigging Manual before installing the product.
Pay attention to rigging instructions included in both Blueprint AV™ and the IS-Series Rigging
Manual.
Use only with the rigging frames/accessories specifi ed by Adamson, or sold with the loudspeaker
system.
This speaker enclosure is capable of creating a strong magnetic fi eld. Please use caution around
the enclosure with data storage devices such as hard drives.
Safety & Warnings
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
3
4
5
6
7
8
9
In an effort to continuously improve its products, Adamson releases
updated accompanying software, presets and standards for its products.
Adamson reserves the right to change the specifications of its
products and the content of its documents with no prior notice.
Page 3
IS7px User Manual
https://www.adamsonsystems.com/en/support/downloads-directory/is-series/is7px
1. Safety & Warnings
2. Product Introduction
3. Wiring
4. Amplication
5. Presets
6. Weatherized
7. Technical Specications

Adamson Systems Engineering | Page 4
IS7px User Manual
IS7px
IS7px Ultra Compact Point Source
• The IS7px is an ultra compact point source enclosure. It contains internal passive crossover, two symmetrically
arrayed 7” LF transducers and a 3” HF compression driver mounted on an Adamson waveguide, available in two
congurations; with dispersion patterns of either 70° x 40° (HxV) or 100° x 50° (HxV) each rotatable in increments
of 90°.
• The operational frequency range of the IS7px is 80Hz to 18kHz. The use of proprietary techologies such as
Advanced Cone Architecture allows high maximum SPL.
• The enclosure has an unobtrusive visual design which blends seamlessly into the surrounding space, is made of
marine grade birch plywood, and has steel rigging discs on the top, bottom, and on each side, to be used with a
wide variety of rigging accessories. Without sacricing low resonance to composite material, the IS7px weighs
only 15 kg / 33 lbs.
• The IS7px is intended to be used as either a standalone system, or a ll enclosure in tandem with other IS-Series
products.
• The IS7px is designed for use with Lab.gruppen’s D-Series line of installation ampliers. The IS7px is designed to
pair easily and coherently with IS-Series subwoofers.

Adamson Systems Engineering | Page 5
IS7px User Manual
IS7px
IS7px Jackplate IS7pbx Jackplate
IS7px & IS7pbx Internal Wiring (IS7pbx only has one input)
PARALLEL
INPUT
PARALLEL
INPUT 1+
1-
2- MF
MF
HF
2+
1+
1-
2-
2+
PASSIVE
CROSS-OVER
Wiring
• The IS7px (967-0006, 967-0009, 967-5006, 967-5009) comes with 2x Neutrik Speakon™ NL4 connections, wired
in parallel.
• The IS7pbx (967-0007, 967-0010, 967-5007, 967-5010) comes with an external barrier strip.
• Pins 1+/- are connected to the internal passive crossover.
• Pins 2+/- are not connected.
px
PARALLEL
pbx

Adamson Systems Engineering | Page 6
IS7px User Manual
IS7px
Amplification
D40:4L
4 IS7px max on a D40 amplier. 8 IS7px max on a D80 amplier.
D80:4L
The IS7px is paired with Lab.gruppen D-Series ampliers.
Maximum quantities of the IS7px per amplier model are shown below.
For a master list, please refer to the Adamson Amplication Chart, found on the Adamson website.
https://adamsonsystems.com/support/downloads-directory/design-and-control/e-rack/283-amplication-chart-9/le
12 IS7px max on a D120 amplier.
D120:4L

Adamson Systems Engineering | Page 7
IS7px User Manual
IS7px
The Adamson Load Library (https://www.adamsonsystems.com/support/downloads-directory/design-and-control/e-
rack/245-adamson-load-library-5-0-1/le) contains presets designed for a variety of IS7px applications. Furthermore, there
are presets designed to pair with either Adamson subs, or Adamson Line Arrays.
For a master list, please refer the Adamson PLM & Lake Handbook, found on our website.
https://adamsonsystems.com/support/downloads-directory/design-and-control/e-rack/205-adamson-plm-lake-
handbook/le
Presets
Cabinet Conguration Applicable Preset
IS7px FR
Fullrange Mode
IS7px Xo80
Low cut at 80Hz
Add 5ms of delay for alignment
of IS-Series subs at same
distance
Cabinet Conguration

Adamson Systems Engineering | Page 8
IS7px User Manual
IS7px
Weatherized
IS-Series weatherized models add an additional layer of environmental and corrosion protection to Adamson’s already
durable cabinet design. Weatherized enclosures are ideal for marine and coastal venues, outdoor stadiums, open-air
performance spaces, and other permanent outdoor installations.
IS-Series weatherized cabinets feature the following additional protective features.
Corrosion resistance
Corrosion resistance extends the lifetime performance of your system in outdoor venues where water, salt and acidity
can impact durability and function.
All structural steel elements of Adamson weatherized cabinets – including rigging and rigging links – are made of a
high yield strength stainless steel alloy that offers 100% corrosion resistance.
Cabinet hardware is made of non-plated stainless steel, designed to provide exceptional rust and corrosion resistance,
particularly in high-saline environments.
Environmental sealing
Additional protection of the cabinet helps ensure that loudspeaker performance isn’t impeded by the harsh
environments in which your system is deployed.
To guard against water and particle intrusion, the same two-part polyurea coating that gives Adamson cabinets their
life-extending exterior protection is applied to the interior of the enclosure, creating a complete seal. Weatherized
models feature an exterior coating with a distinctive smooth nish that allows for easy cleaning and removal of
contaminants like dirt, grime, salt water or sand.
To protect against dust and other particles, a ne stainless steel mesh has been added to all points of entry including
behind the front grille screens.
Cabling for the IS-Series weatherized cabinets is pre-wired and protected inside a gasket-sealed jackplate, with gland
nuts in place to seal the connection points.
DAMSON 1S7PWX
A

Adamson Systems Engineering | Page 9
IS7px User Manual
IS7px
Technical Specifications
**12 dB crest factor pink noise at 1m, free eld, using specied processing and amplication
Frequency Range (- 6dB) 80 Hz - 18 kHz
Nominal Directivity (-6 dB) H x V 70° x 40° or 100° x 50° - Rotatable
Maximum Peak SPL** 135
Components LF 2x ND7-LM16 7” Neodymium Driver
Components HF NH3-8 3” Diaphragm / 1.4” Exit Compression
Driver
Nominal Impedance Passive 6 Ω
Power Handling (AES / Peak) Passive 500 / 2000 W
Rigging Integrated Rigging System
Connection 2x Speakon™ NL4 or Barrier Strips
Height (mm / in) 527 / 20.75
Width Front (mm / in) 251.5 / 9.9
Width Rear (mm / in) 170 / 6.7
Depth (mm / in) 356 / 14
Weight (kg / lbs) 15.5 / 34.2
Colour Black & White (Standard), RAL Colours (On
Demand)
Processing Lake
527 mm / 20.75 in
356 mm / 14 in
251.5 mm / 9.9 in
170 mm / 6.7 in
800 Hz 1.5 kHz 3 kHz 6 kHz 20 kHz10 kHz400 Hz200 Hz100 Hz
0°
180°
180°
90°
90°
IS7px 70x40 Horizontal Pattern IS7px 100x50 Horizontal Pattern
800 Hz 1.5 kHz 3 kHz 6 kHz 20 kHz10 kHz400 Hz200 Hz100 Hz
0°
180°
180°
90°
90°