Adaptec ICP 5045BL User manual

--------------------------------------------------------------------
README.TXT
ICP ICP9085LI/ICP5085BR SAS RAID Controller
ICP ICP9047MA/ICP9087MA SATA RAID Controller
ICP ICP9014RO/ICP9024RO SCSI RAID Controller
ICP ICP5805BL/ICP5045BL/ICP5085BL/ICP5125BR/ICP5165BR Unified Serial Controllers
as of September 14, 2007
--------------------------------------------------------------------
Please review this file for important information about issues
and erratas that were discovered after completion of the standard
product documentation. In the case of conflict between various
parts of the documentation set, this file contains the most
current information.
NOTE: The latest BIOS and documentation can be downloaded
from www.icp-vortex.com.when they become available.
The following information is available in this file:
1. Software and Documentation
1.1 Controller & Utility Software
1.2 Documentation on this CD
2. Installation Instructions
3. General Cautions
4. Known Limitations
4.1 Booting to a bootable CD
4.2 ICP9014RO/ ICP9024RO controllers
4.3 ICP9024RO controller
4.4 ICP9085LI controller
4.5 Using the controller in a Dell Precision 530
4.6 ACU utility
4.7 FreeBSD
4.8 ICP Storage Manager
4.9 ICP5085BR/ICP ICP5805BL/ICP5045BL/ICP5085BL/ICP5125BR/ICP5165BR
controllers
4.10 OpenServer 6.0
4.11 SAS and SATA controllers and Adaptec 335SAS enclosure
4.12 Using the ICP5085BR in a Gateway 920
4.13 Creating an Array from the ICP Storage Manager CD
4.14 Using the controller with an Adaptec S50 JBOD Enclosure
4.15 SMART errors on SATA controllers
4.16 Firmware upgrades
4.17 RAID 10/50/60 array leg limitations
4.18 Microsoft VDS Storage Manager LUN Error
4.19 ICP5085BR controller
4.20 UnixWare and OpenServer
4.21 SATA disks do not support Dual Path with Expanders
4.22 Usage of firmware, utilities and flash tools
4.23 DOS OS not supported
4.24 DAT drive restoration fails when spanning tapes
--------------------------------------------------------------------
1. Software and Documentation
1.1. Controller & Utility Software

Note: The latest versions of BIOS and driver software
can be downloaded from www.icp-vortex.com when they become
available.
- BIOS
- ACU
- Windows Drivers
o Windows 2000 Server, Advanced Server, Professional
o Windows 2003 Server, Enterprise, Standard, and Web Edition
o Windows XP Professional
o Windows Vista - All versions
- Linux Drivers
o Red Hat Enterprise 4.0, IA-32 and x64
o Red Hat Enterprise 5.0, IA-32 and x64
o SuSE Linux Enterprise Server 9.0, IA-32 and x64
o SuSE Linux Enterprise Server 10.0, IA-32 and x64
- FreeBSD Drivers
o FreeBSD 5.3, 5.4 (ARCCONF 32-bit only)
o FreeBSD 6.1 (ARCCONF 32/64-bit only)
- SCO Drivers
o OpenServer 6.0
o UnixWare 7.1.4
- VMware Drivers
o VMware ESX Server 3.0.1
- Sun Solaris Drivers
o Solaris 10 Update 1
1.2. Documentation on this CD
- ICP SAS, SATA, and SCSI RAID Controllers Installation
and User's Guide
- ICP SAS, SATA, and SCSI RAID Controllers
README.TXT file
--------------------------------------------------------------------
2. Installation Instructions
- The ICP SAS, SATA, and SCSI RAID Controllers Installation
and User's Guide contains complete installation information for
the controllers and drivers, as well as complete instructions
for all utilities. The ICP Storage Manager User's Guide

contains complete installation information for the ICP
Storage Manager software.
--------------------------------------------------------------------
3. General Cautions
- While an array is being built or cleared, DO NOT remove and
reinsert any drive from that array. Doing so may cause
unpredictable results for any of the controller's arrays.
- While a drive is being cleared, DO NOT try to include it in a
new array. Doing so may cause unpredictable results.
- DO NOT move drives containing an array or volume from one
controller to another while the power is on. Doing so could
cause the loss of the array configuration or data, or both.
Instead, power off both affected controllers, move the drives,
and then restart.
--------------------------------------------------------------------
4. Known Limitations
4.1 Booting to a bootable CD
A system cannot boot to a bootable CD in a SCSI optical drive,
such as CD or DVD drive, connected to the ICP9024RO SCSI RAID
controller.
4.2 ICP9014RO/ICP9024RO controllers
Use only the utilities/flash tools included with this release.
Upgrade any existing tools to those included with this
release, as this release supports additional features that
were not available with previous releases
4.3 ICP9024RO controller
With an Intel Pro/1000 MT 32-bit PCI NIC on the system, after
controller POST the controller goes to a
BLED 0xEF NMI_HANDLER_FAILURE.
4.4 ICP9085LI controller
When the controller is connected to an external enclosure,
only the internal SAS connector closest to the bracket is
available for use with internal SAS or SATA disk drives. The
other internal SAS connector shares the SAS bus with the
external connector, which is occupied.
Various devices on the serial bus can negotiate at different
speeds. To determine the speed at which a particular device
is negotiating, view the device properties in ICP Storage
Manager. (Click on the device, then click the Properties
button.)
4.5 Using the controller in a Dell Precision 530

When using the controller in a Dell Precision 530 with
Diskercise and Diskstress, data corruption/miscompares may
occur.
4.6 ACU utility
On some Intel and IBM systems, when you try to run the ACU,
this message appears:
“Not enough free memory to load the utility!
Press any key to attempt loading the utility forcibly
OR Wait for the system initialization to be completed
[Default]”
This is normal. On Intel systems, wait for the system
initialization to be completed. Then the ACU will run. On IBM
systems, press any key when prompted to load the utility
forcibly.
The ACU /C0 buildall command does not start a build/verify on
RAID 1 or RAID 10 arrays that are being created using the
quick init method.
4.7 FreeBSD
ICP Storage Manager is not supported in FreeBSD; storage
management must be done through the ICP Configuration
Utility (ACU) and ARCCONF command line utility.
4.8 ICP Storage Manager
After a rebuild and waking up from hibernation, a controller
may be detected incorrectly in ICP Storage Manager.
Press F5 to correct the problem.
4.9 ICP5085BR/ICP ICP5805BL/ICP5045BL/ICP5085BL/ICP5125BR/ICP5165BR
controllers
When the controller is installed in PCI-E slot 2 of a
Dell PE 1800 system, there is no BIOS POST.
When the controller is installed in PCI-E slot 3 in a
Dell PE 1800 system, the system halts and the keyboard locks
up.
When the controller is set to boot from a RAID array and a
second RAID array is created, the controller may no longer
be able to find the boot drive.
When the controller is installed in the primary PCIe slot of
an Intel 955X or nVidia nForce4 (Intel edition) motherboard,
if you use the Adaptec Flash Utility to perform a Mode0 flash,
the controller will show incorrectly and cannot be flashed. If
a Mode0 flash is required, install the controller in an
alternate PCIe slot or alternate computer.
4.10 OpenServer 6.0

Arrays may not be displayed correctly, even after you restart
your computer.
To resolve the problem:
As root, run 'resmgr -r -m vtoc' until it fails. Then, as
root, run '/etc/conf/bin/idconfupdate -f'. Then, reboot.
4.11 SAS and SATA controllers and Adaptec 335SAS enclosure
When the Adaptec 335SAS enclosure is attached to an ICP
SAS controller, such as ICP9085LI or ICP5085BR, the
enclosure numbering nomenclature starts with "0". For
example, if two Adaptec 335SAS enclosures are connected to an
ICP9085LI SAS controller, management tools such as Storage
Manager will denote the enclosures as "Enclosure 0" and
"Enclosure 1". When the Adaptec 335SAS enclosure is attached
to an Adaptec SATA controller, such as ICP9047MA or
ICP9087MA, the enclosure numbering nomenclature starts with
"14". For example, if two Adaptec 335SAS enclosures are
connected to an ICP9087MA controller, management tools such
as Storage Manager will denote the enclosures as
"Enclosure 14" and "Enclosure 15".
4.12 Using the ICP5085BR in a Gateway 920
When more than one ICP5085BR controllers are installed in a
Gateway 920 server, the system will not POST.
4.13 Creating an Array from the ICP Storage Manager CD
When you create an array with the ICP Storage Manager
bootable CD, the maximum size of the array is 2 TB.
4.14 Using the controller with an Adaptec S50 JBOD Enclosure
Temperature warnings from Adaptec S50 JBOD Enclosure (firmware
version T016) are not shown in Adaptec Storage Manager (or on
the enclosure).
4.15 SMART errors on SATA controllers
During POST, SMART errors for disk drives connected to SATA
controllers are indicated as follows:
o N = No SMART errors reported
o Y = SMART errors reported
o N/A = Disk drive does not support SMART error reports
4.16 Firmware upgrades
Check your controller BIOS settings after upgrading the
controller firmware/BIOS, as the BIOS may have been reset to
its default settings during the upgrade.
4.17 RAID 10/50/60 array leg limitations

A RAID 10, RAID 50, or RAID 60 array cannot have more than 32
legs when created using the Build method. Maximum disk drive
count is only limited by RAID level. For instance, a RAID 10
array built with 32 RAID 1 legs (64 disk drives) is supported;
a RAID 5 array built with 32 RAID 5 legs (96 disk drives) is
also supported. Although you can create a RAID 10 array with
more than 64 drives using the Quick Init method, the maximum
number of build/verify operations that can happen at any one
time is 32; therefore, such an array could not be verified.
4.18 Microsoft VDS Storage Manager LUN Error
On some systems when creating a new LUN, the Microsoft VDS
Storage Manager for SANs snap-in may not work properly and
crash with an MMC snap-in error.
4.19 ICP5085BR controller
On Intel 945X or 955X motherboards with Mode0 set, the controller
is not recognized when installed in the primary 16x PCIe slot.
4.20 UnixWare and OpenServer
Adding or moving controllers in an existing UnixWare or OpenServer
system may cause some device resources to change, which may lead
to the operating system being unable to boot. Currently, there
is no workaround available in the operating system. Before
installing the operating system, make sure all PCI devices are
either enabled or installed.
The individual behavior and affected devices will vary from system
to system. This is due to the different ways in which motherboards
may handle their PCI bus layouts, and how those layouts could be
changed when installing or rearranging devices. If the bus layout
changes and affects a critical system device (video, boot controller,
etc.) then the operating system may be unable to recover from that
change and be non-bootable.
4.21 SATA disks do not support Dual Path with Expanders
Connect Dual Path SAS Enclosures with 2 Expanders only via one
Expander when using SATA disks, SATA disks do not support
Dual Path. If SATA disks are connected using 2 Expanders the
controller BIOS may crash.
4.22 Usage of firmware, utilities and flash tools
Use only the utilities/flash tools included with this release.
Upgrade any existing tools to those included with this release,
as this release may support additional features that were not
available with previous releases.
4.23 DOS OS not supported
The DOS environment is supported for Adaptec tool execution only
(AFU.EXE and ACU.EXE).

4.24 DAT drive restoration fails when spanning tapes
When restoring from two or more tapes with a Sony SDX-470,
Sony SDX-570, or Quantum DLT V4 DAT drive, the operation aborts
automatically when restoring the second tape but gives the
(erroneous) message "Restore Operation has Completed".
--------------------------------------------------------------------
(c) 2007 Adaptec, Inc. All Rights Reserved.
This software contains the valuable trade secrets of Adaptec or its
licensors. The software is protected under international copyright
laws and treaties. This software may only be used in accordance with
the terms of its accompanying license agreement.
No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without prior
written consent of Adaptec, Inc., 691 South Milpitas Blvd.,
Milpitas, CA 95035.