ADC Ultra-8 User manual

ControlPanel
OperatorsManual
TOSUITAS208KEYPAD
AdvancedDigitalControls AS208-OM-1.2
www.msealarms.com.au

Page1 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
Ultra-8Control Panel
AS208 OPERATORSMANUAL
Copyright2002 byAdvanced DigitalControlsNZLtd
Auckland,NewZealand
DocumentPartNumber:AS208-OM-V1.2
This documentisprovided tosuitthe Ultra-8 Control Panel (CP108)
FirmwareVersion: 8.64+
CopyrightNotice
All rightsreserved.Nopartofthispublication maybe reproduced,transmitted orstored ina
retrievalsysteminanyformorbyanymeans,electronic,photocopying,mechanical,recording,
orotherwise,withoutthe writtenpermission ofAdvancedDigitalControlsNZLtd
Notice of Liability
Whileeveryprecaution hasbeentakeninthe preparation ofthisdocument,neitherAdvanced
DigitalControlsNZLtdnoranyofitsofficialrepresentativesshallhaveany liabilitytoany
person orentity withrespecttoanyliability,damageorlosscaused oralleged tobe caused
directlyorindirectly bythe information contained inthisbook.
Advanced DigitalControlsNZLtdreservesthe righttomakechangestofeaturesand
specificationsatanytimewithoutpriornotification intheinterest ofongoingproduct
developmentand improvement.
www.msealarms.com.au

Page2 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
TABLEOFCONTENTSTABLEOFCONTENTS
Introduction 3
The Keypad 3
SystemIndicators 4
ButtonDefinitions 5
OptionalLabels 5
MenuFunctionsDefinitions 6
ArmingThePanelInAWAY Mode 6
ArmingThe PanelInSTAY Mode 7
Disarming the Panel 7
AddingorDeletingCodes 7
Menu 1 – Playback 8
MemoryEventList 9
Menu 2 – Exclude Mode 10
Menu 3 – ControlMode 10
Menu 4 – BuzzerPitch 11
Menu 5 – DayAlarm ON/OFF 11
Menu 6 – FaultAnalysis 12
Hold-UpDuressAlarm 12
Acknowledging Domestic &VoiceAlarmMessages 12
VoiceBoardOperatingInstructions 13
www.msealarms.com.au

Page3 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
INTRODUCTIONINTRODUCTION
Thankyouforselecting the Ultra-8 controlpaneltoprotect yourfamilyand yourproperty.
ThisAdvanced DigitalControls Ultra-8 version alarmcontrolpanelhasbeen designed to
provide the most requested featuresforboththe installer&the end-user.Thesefeatures
includeeaseofinstallation,ease ofprogrammingand userfriendly operationall ina package
thatisreliable,functionaland attractive.
Utilising manyyears ofexperienceinthe security industryand implementing valuablefeedback,
weareproud toprovide you withanewgeneration ofalarmcontroller.The Ultra-8 is a New
Zealand designed and builtproductthatbringsyou the quality and features, whichyou deserve
atan affordableprice.Inaddition tothe advanced design,onlythe highestqualitycomponents
havebeen used inthe production ofthis Ultra-8 paneltoensurethe highestdegreeof
reliability.
Thismanualwillguideyou throughthe operation and programmingofyour Ultra-8 alarm
panel.
Add onfeaturesliketheWR40 &RX40 radioreceiversthatcan operateanyofthe 4outputsor
arm/disarmyourpanelwithup to8keyfob radiopendants.
The autodialleron yourpanelcanbe setup tosend high speed signalstoamonitoringstation
or"domesticdial"sending anAlarmtone toanyorall ofthe4possible phonenumbers
FOR MORE INFORMATIONFOR MORE INFORMATION
Pleasevisitourwebsite, www.adcsecurity.com,tofindoutmoreinformation aboutthe Ultra-8
AlarmController.
THEKEYPADTHEKEYPAD
Ultra-8 AS208 keypad is modernandsleekindesignand
blendsintoanydécor.
The removabledoorallowsthe button tobe hidden when
notinuse.The backlitepoxy coated buttonsgiveyearsof
durabilityin all conditions. Singlebuttonsarmingoptions
allowingyouto“arm &go”in asecond making life easier.
Alargedisplayscreen showssystemstatus ata glance
withouttomany confusingindicators.AWAY &STAY
indicatorsshowpanelstatuswhileFAULT&SYS
indicatorsshowtheintegrityofthe Ultra-8
MEDICAL
PANIC
FIRE
www.msealarms.com.au

Page4 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
SYSTEMINDICATORSSYSTEMINDICATORS
AWAYINDICATOR
The AWAY indicatoris usedtoinformyouthatthe systemis armed in AWAY mode
Indicator Definition
ON System Armedin AWAY mode
OFF System isnotarmed in AWAYmode
FLASHING FAST Zoneshave been Isolated
STAYINDICATOR
The STAY indicatoris usedtoinformyouthatthe systemis armed in STAY mode
Indicator Definition
ON System Armedin STAY mode
OFF System isnotarmed inSTAY mode
SYSINDICATOR
The SYSindicatorisused toinformyou ofeventsinthe panelmemory
Indicator Definition
FLASHING Aneweventisin progress
ON The neweventhascleared
OFF Noneweventshaveoccurred
FAULT INDICATOR
The FAULTindicatorisused toinformyou whenan tamperalarm occurs
Indicator Definition
FLASHING TamperorPanicalarmin progress
ON Tamperacknowledged butnotcleared
OFF Noalarmcondition
The FAULT indicatorwill flashwhen analarmoccurs e.g. TamperAlarms. When the
alarmis cleared,byenteringavalidcode the FAULT indicator will turn off.
Ifthe reason forthealarmis notcleared,e.g. Tamperremainsopen,the FAULT indicator
will remainonsolid until thecause isfound and clearedfully.
www.msealarms.com.au

Page5 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
MEDICAL
PANIC
FIRE
BUTTONDEFINITIONSBUTTONDEFINITIONS
AWAY Button
Thisbutton isforarmingyour Ultra-8 panelin AWAYMODE
STAY Button
Thisbutton isforarmingyour Ultra-8 panelin STAYMODE
PRG Button
Thisbutton isforaddingordeletingcodesorforenteringinstallermode
MENU Button
This buttonfollowed byanumberwill allowyoutoexecuteadditionalcommandsaslisted
on the page7
êê Button
Thisis used fordifferentprogrammingoptions.
OPTIONAL LABELSOPTIONAL LABELS
PANIC -1&3ButtonsSimultaneously
This will cause aPANICAlarm.This will soundthesirens
andifconnected to amonitoring stationinformthemofa
Panic situation.
FIRE-4&6ButtonsSimultaneously
This will causeaFIREAlarm.Thiswill soundthesirens and
ifconnectedto a monitoringstation monitored informthem
ofaPanic situation.
MEDICAL-7&9ButtonsSimultaneously
This will causeaMEDICALAlarm.Thiswillsoundthesirens
andifconnected to amonitoring stationinformthemofa
Panic situation.
www.msealarms.com.au

Page6 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
MENUFUNCTIONSMENUFUNCTIONS
Menu 1 HoldDown1MemoryPlayback
Menu 2 HoldDown2ExcludeMode
Menu 3 HoldDown3ControlMode – Day Alarm
Menu4 HoldDown4BuzzerPitch
Menu 5 HoldDown5DayAlarmON/OFF
Menu 6 HoldDown6FaultAnalysis
Menu êê - KeypadLock
¤HoldDown functions workafter2 seconds
Menu 1-MemoryPlayback
Thiscommand allowsyou toviewthe last127 eventsstored inthecontrolpanel’s
memoryon thekeypad
See page8forfurtherinformation
Menu 2-ExcludeMode
Thiscommandallowsyou totemporarily excludeorby-pass zonesofyourchoicewhen
armingyourpanel
See page10forfurtherinformation
Menu 3-ControlMode
This command will allowyou to switchDayZonesOn/Off orto controloutputs
See page10 forfurtherinformation
Menu 4-BuzzerPitch
This command allows youtochangethe pitchofthe buzzer
See page11forfurtherinformation
Menu 5-DayAlarmON/OFF
This command allows you toswitch ONand OFF theDayAlarm.
See page11forfurtherinformation
Menu 6-FaultAnalysis
This commandallowsyouto viewanysystemfault.
See page12 forfurtherinformation
www.msealarms.com.au

Page7 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
Menu êê -KeypadLock Mode
This command will lockthe keypad fromanywandering hands. The MENU Button will
flashtoindicatethatthe keypad is locked.TounlockthekeypadpressMenu ê
ARMINGTHEPANELINAWAYMODEARMINGTHEPANELINAWAYMODE
+
+
OR
3-6 Digit
Code
Pressthe AWAY key. The AWAYindicatorwillcomeon.Yourpanelwill beginbeeping
itsexit delay.Duringthistime itis optionalto press the AWAY keyagaintodisarm.(to
preventaccidentalarming,the panelcan be programmed torequirea code toarmthe
panel.Todo sopressAWAYand enteryourcodefollowed bythe ENTER key.
ARMINGTHEPANELINSTAYMODEARMINGTHEPANELINSTAYMODE
+
+
OR
3-6Digit
Code
Pressthe STAY key. The STAY indicatorwillcomeon.Yourpanelwillbeginbeepingits
exitdelay.Duringthistime itisoptionalto pressthe STAY keyagaintodisarm.(to
preventaccidentalarming,the panelcan be programmedtorequireacode toSTAY arm
the panel. Todo sopressSTAY andenteryourcode followed bythe ENTER key.
When armingSTAY modeall exitand entrydelayswillapplyasprogrammed,howeverif
the ENTER button ispressed afterarmingSTAY mode,then allexitand entrydelayswill
be cancelledforthatarmedcyclemakingeverythinginstant.
DISARMINGTHEPANELDISARMINGTHEPANEL
+
3-6Digit
Code
Todisarmthe panel,enteryour1to6digit code then pressthe ENTER key.
If yoursystemhasan optionalradio cardinstalledyoursystemcanalsobe armed or
disarmed withyourremotekeyfobpendant.
ADDINGOR DELETINGCODESADDINGOR DELETINGCODES
The Ultra-8 can acceptasmanyas10differentusercodesof1up to6digitsin length.
Yourinstallercan setyou up toenteryourcode atusercode 1(Mastercode,Defaultto
2580)You will nowbe abletoadd,deleteorchange codesforotherusers.
Bydefaultonly themastercodehaspermissionto changeadd orremovecodes. Anynew
codesadded will beable to arm,disarmand puteitherarea ofthe panelintomonitor
mode.Usercodescan be limited in theirlevelsofpermission ifrequired.Pleaseaskyour
installer.
www.msealarms.com.au

Page8 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
Makingsurethepanelis notarmed,keyinthe followingsequence:
+
+
Master Code
The PRG buttonwill starttoflash,indicatingreadiness to acceptnewprogramming.
Toload,forexample,usercode3withacode 4321,keyinthe followingsequence:
+
+
If thereisan existingcode alreadyinthataddressitwill beflashedback on the keypads
LEDdisplay. Entering thenewcodewill deletetheoldand thenewcodewill beflashed
backtoyou.
+
Continued on the nextpage….
The panelwillgive3shortbeepstoindicatecorrectentryor1longtone ifnotaccepted.
Toremoveorclearausercode numbere.g.user3,keyinthe followingsequence
Toexitoutofprogrammode key
¤OntheLEDdisplay0 isindicated by AWAY indicatorand 9by STAY indicator.
MENU1MENU1--MEMORY PLAYBACKMEMORY PLAYBACK
Thiseventmemoryisdisplayed viathe keypad withthe mostrecenteventshownfirst
andsubsequenteventsfollowingindescendingorderfromnewesttooldest.Eachevent
isseparated byabeep tone.
Thereareanumberofeventswhicharestored inmemorywhichdo nothaveaspecific
indicatorassociated with themsuch asPanic and Duress.
Othereventssuchas tampersand lowbatteryareshared acrossmanydevices. Forthis
reasonthe followingtablehasbeen created.
This table details whichindicatorlightscorrespond to whicheventsinmemory.
Toview EVENTMEMORYPLAYBACK MODE press MENU +1
The last 127 events willbe played backonthe keypadLEDsdisplayed sequentiallyat2
second intervals fromthe mostrecenteventbackwards.
Togettoaspecificeventrapidly press the êê keyrepeatedly and the memory display will
be spedup accordingly
Toexit memorymode press ENTER
Continued on the nextpage….
+
+
+
+
+
www.msealarms.com.au

Page9 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
MEMORYEVENTLISTMEMORYEVENTLIST
EVENTTYPE DEVICE INDICATOR STATUS
ACTIVATION Zones1-8 LED’s1-8 OnSteady
EXCLUDE Zones1-8 AWAYLED
LED’s1-8 Flashes Fast OnSteady
DETECTOR TAMPER(SHORTCIRCUIT) Zones1-4 FAULT
LED’s1-4 Flashing OnSteady
DETECTORTAMPER(OPENCIRCUIT) Zones5-8 FAULT
LED’s5-8 Flashing OnSteady
CABINETTAMPER CabinetorSatellite FAULT Flashing
LOWBATTERY Control Panels
Battery SYS
LED1 OnSteady OnSteady
MAINSFAILURE Control PanelsMains
Supply SYS
LED2 OnSteady OnSteady
WIRELESS ZONELOWBATTERY Wireless Detectors
Zone 1-8 LED’s1-8 Flashing
WIRELESS KEYFOBLOWBATTERY Wireless Keyfob
User1-8 FAULT LED’s1-8 OnSteady Flashing
PANIC (BUTTONS1&3PRESSEDTOGETHER) Keypad Panic SYS Flashing
FIREALARM (BUTTONS4&6PRESSED
TOGETHER) Keypad Fire SYS
AWAY Flashing Flashing
MEDICALALARM (BUTTONS7&9PRESSED
TOGETHER) Keypad Medical SYS
STAY Flashing Flashing
WIRELESS KEYFOBPANIC Wireless Keyfob
User1-8 SYS LED1-8 Flashing Flashing
ARMEDINAWAY MODE Panel isArmed AWAY OnSteady
ARMEDINSTAYMODE Panel isin STAY
mode STAY OnSteady
KEYPADDURESSALARM DuressAlarm FAULT
AWAY&STAY OnSteady Flashing
SUPERVISEDWIRELESS ALARM SupervisedWireless
Detector SYS FAULT
LED’s1-8
OnSteady
Flashing
Flashing
ZONEINACTIVITY Zones1-8 AWAY
FAULT
LED’s1-8
Flashing Fast
OnSteady
OnSteady
TELEPHONELINEFAILURE Phone LineFailure FAULT
LED3 OnSteady OnSteady
www.msealarms.com.au

Page10 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
MENU2MENU2--EXCLUDEMODEEXCLUDEMODE
Thiscommandallowsyou totemporarily excludeorby-pass zonesofyourchoicewhen
armingyourpanel.The excluded zoneswillgobacktonormalthe nexttimeyoudisarm
thepanel(except24Hourzoneswhichmustbe manuallyre-included).Atypicalexample
wouldbe ifyou wanted toletyourpetrun around in the garagewhen yoursystemis
armed,you couldchoose toexclude thatdetector(sayZone 1)fromthe system.
Toexclude zone 1,keyinthe followingsequence:
MENU+2+1+ENTER
WhentheENTERkeyispressedthe AWAY indicatorwillflashveryfast (provided thatall
zonesaresealed)toindicatethe exclude function isactivebeforearming,anynumberof
zonesmaybe excluded inthismanner.PressMENU2againtoadd orremoveexcluded
zones.Pressbutton 1andENTERagainandzone1will be included.
¤24 hourzones(forexamplesmokedetectors)willremainexcludeduntil theyare
manually includedagain.All otherexcluded zoneswill returntonormal"included"mode
automatically thenext timethepanelisarmed.
It is advisabletovacatethe secured area beforethe exit delayexpires
You maynowARMthe panel.
MENU3MENU3--CCONTROLMODEONTROLMODE
Outputsareprogrammablecontactson the paneloroutputexpanderboardthatcan be
used toswitchorpowerexternaldeviceson oroff. Note:Yourinstallermustenablethisfeature.
PresstheMENU 3button
The SYS indicatorwill beon steady
Pressthe numberkeycorrespondingtothe outputyou wishtoturnon i.e.-output3turns
on waterheating.
Pressthe 3key, the 3indicatorwill illuminate indicating the outputison.
Press the ENTERkeytoconfirmthe operation and returntonormalkeypad function
Tocheckwhatoutputsare on simplypress the MENU3 keys again, indicator3 will be
illuminated,pressingthe 3 &ENTERkeys again will toggle theoutputoff.
www.msealarms.com.au

Page11 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
MENU4MENU4--BUZZERPITCHBUZZERPITCH
This commandallowsyou tochangethe pitchofthe buzzeron the keypad fromahigh
pitch toa lowpitchorswitch the buzzeroff.E.g.bedroomsituations.
Number Pitch
1HighestPitch
2
3
4
5MediumPitch
6
7
8
9LowestPitch
0BuzzerOff
e.g.PressMENU+4+5+ENTER. Thissetthe buzzerpitchtomediumpitch.
MENU5MENU5 –– DAYALARMON/OFFDAYALARMON/OFF
The DayAlarm isazone thatcan be used tooperateabuzzerorlighttoletyou knowthat
youhaveavisitorwhen the alarmis disarmed.
PressMENU +5toswitchtheDayAlarmON/OFF
The buzzerwillbeep 3timestoletyou knowthatyou haveswitched the DayAlarmON
The STAY button will flashindicating thatDayAlarmis ON
¤When the system isarmed itchangestobecomeafull alarmzone.Ask yourinstallerformoreinformation.
www.msealarms.com.au

Page12 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
MENU6MENU6--FAULTANALYSISFAULTANALYSIS
The MENU6function will giveyou an eightpointfaultanalysisofcurrentsystemfaults.
The SYS indicatorwill flash whena systemFAULToccurse.g. "mainsfailure".
Press MENU+6toviewanyFAULTconditions.
The SYS indicatorwill remainonsteadyand LED’s 1-8will beilluniatedcorospondingto
tablebelow.
If the systemfaulthasnotbeen acknowledged aftertheeventclears,e.g. "mainsreturns"
,normalcondition,the SYS indicatorwillremainsteady showingyouthat the eventis now
cleared.Thisallowsyou tosee iftherehavebeen anyfaults whilethealarm hasbeen
set. Toclearthisindicatorpress MENU6 oritwill simply clearnexttimeyouarmthe
panel. The SYS indicatorcan be programmed toextinguish upon “normal condition”thus NOTdrawing
yourattention toanypastFAULTS.Askyourinstallertosetthisoption.
The MENU6function will giveyou an eightpointfaultanalysisofcurrentsystemfaults
anddisplaythemfromZones 1-8asperthe tablebelow
LED#1 LowBattery LED#5 Wireless KeyfobLowBattery
LED#2 MainsFailure LED#6 Supervised DetectorFailure
LED#3 Telephone Line Failure LED#7 Zone InactivityTimeout
LED#4 WirelessDetectorLowBattery LED#8 DiallerKiss-offFailure
HOHOLDLD--UPDURESSALARMUPDURESSALARM
The duressdigitisanumberfrom1-9.Tocreateaduressalarm,the duressdigitmustbe
pressedbeforethe codetodisarm.ie,If the usercode is 2580 and the duressdigitis5,
then enteringacode of52580 +ENTERwouldcreateaduressalarm.Thesirenswon't
sound, butthe diallerwoulddialtothe Monitoring Station and reportaDURESS ALARM.
Pleaseask yourinstallertosettheduressdigit.Itisdefaultfor0, whichmeansthe
duress option is disabled.
ACKNOWLEDGINGDOMESTICACKNOWLEDGINGDOMESTIC&VOICEALARM MESSAGES&VOICEALARM MESSAGES
Ifanalarmoccursthatis setforDomestic orVoiceReporting, the panelwill call thepre-
programmedtelephone number/s. When thecall is answeredasiren tone orvoice
messagewillbe sent.Thepanelwill thenwait for5 secondslookingforaDTMFtone on
the line (aDTMFtone isgenerated when anykeyon a normalpushbutton telephone is
pressed),If the panelreceivesaDTMFtone it willhang-up andcancelanyfurthercalls
forthatparticularalarmevent. If notitwillrepeatthe siren tone orvoicemessagea
further3timeswiththe 5second pauseinbetweenwaitingtohearaDTMF tonethatwill
stop the alarmreporting,ifno DTMFtone wasreceived afterthe totalof4attempts the
panelwilldialthe nextpre-programmednumberon the listand repeatthe sequence
again,ifinthemeantime the alarmpanelisunsetanyfurthervoicealarmreportsare
automatically cancelled (withthe exceptionof24houralarmsthatmustbecancelledbya
DTMFcode only).
www.msealarms.com.au

Page13 AdvancedDigitalControlsAdvancedDigitalControls AS208-OM-V1.1
VOICEBOARDOPERATIVOICEBOARD OPERATINGINSTRUCTIONSNGINSTRUCTIONS
The VB-90 voiceboardmustbe fitted forthesefunctionstowork.Pleaseask you installerformoreinformation
CommandControlOperation
If Command Controlis setup thenavalidcode holdercan call the alarmusingany
standardpushbuttontelephone.When thepanelanswersthe in-coming call itwill
generate2differenttonesforapproximately2secondseach.When the toneshave
finished the panelwillbe lookingforavalid4digitDTMF code e.g.1,2,3,4.If the code
entered inatthe keypad on the telephone matchesone ofthe validDTMFcodes
programmedintothepanelthe appropriatevoice messagewill be sent.
Forexample,If the code 1,2,3,4wasthe Arm/Disarmcode forArea Aand the code
holderentered thiscode inattheirtelephone,the alarmpanelwiltrespond withthe voice
messagerelating tothe currentstatusofArea A.Nowbypressingthe êbutton atthe
remote telephone the panelwiltchange thestatus ofArea A(ifalreadyArmed itwill
Disarmthe panelorviceversa)and givethe correspondingvoicemessagerelatingto
this newstate.OutputControlisverysimilarwiththe exception thatthe outputnumber
you wishtocontrolmust be entered inafterthe valid4digitcode e.g.ifthe output control
code was2,5,8,0 and you wanted to controloutput# 2thenthe code2.5,8,0,2mustbe
entered inatthe remotetelephone.Onceagain,ifthiswasa validcode tocontrolthe
outputs the panelwill respondwiththe voicemessagerelatingtothecurrentstatusof the
outputconcerned (inthiscaseoutput2).Bypressingthe êbutton the stateofthe output
willbechanged andthemessagerelating tothe newstatuswill besent.
Atanytimeifan incorrectcodeisaccidentallyentered asinglepressofthe#buttonat
the telephone will resetall digits sent ready to anewsequenceof4 digits.
MicrophoneControl
Ifthe optionalmicrophone is connectedtotheVoiceBoard,itis possible to dialintothe
alarmpanelfromanytelephoneand turnon the Microphone inputtoallowaudible
verification ofanintruderonsite.
Todo this,oncethepanelhasanswered the in-comingcall asbefore, allyou haveto do
isenterinthe valid4digitMicrophone code followed bythe êbutton.To turnthe
microphone input offyousimplypress the êbutton again. If the microphone is notturned
off properlyitisautomaticallyturned off whenthe callisterminated.The various
CommandControlprogramaddresscodesforbothpanelsarelistedin the chartbelow.
www.msealarms.com.au

Installation NotesInstallation Notes
Installation CompanyInstallation Company
TechnicianTechnician
PhoneNumberPhoneNumber
InstallationDateInstallationDate
WarrantyExpiresWarrantyExpires
Entry&ExitTimersEntry&ExitTimers (seconds)
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
Exit STAY DAY
ZoneDescriptionsZoneDescriptions MODE ALARM
Zone 1 ¨¨
Zone 2 ¨¨
Zone 3 ¨¨
Zone 4 ¨¨
Zone 5 ¨¨
Zone 6 ¨¨
Zone 7 ¨¨
Zone 8 ¨¨
HoldHold--UpDuress AlarmDigitUpDuress AlarmDigit
NotesNotes
www.msealarms.com.au