Adexa UC200-2036D User manual

UNDER-MOUNT HOOD
MODEL : UC200-2036D
INSTALLATION GUIDE / USE AND CARE MANUAL
IMPORTANT: Read and save these instructions.
Installer: Leave this manual with the owner.
2023
Owner: Keep this guide for future reference.
A

Table of Contents
APPROVED FOR APPLIANCES OF INDOOR USE ONLY.
READ AND SAVE THESE INSTRUCTIONS.
PLEASE READ THE ENTIRE INSTRUCTIONS BEFORE YOU
IMPORTANT: Keep these instructions in order to provide them to the electrical inspector in your area.
INSTALLER: Please leave these instructions with the owner of the unit.
OWNER: Keep these instructions for future reference.
SECURITY WARNING:
BEGIN. INSTALLATION OF THE UNIT MUST RESPECT ALL
CODES.
Turn off the power circuit in the electrical panel and lock the front panel before
connecting the wires of this unit.
Requirements: 2 2 0V , 5 0Hz
3
IMPORTANT SAFETY PRECAUTIONS...................................................................... 4-5
INSTALLATION INSTRUCTIONS............................................................................ 6-13
OPERATING THE HOOD.......................................................................................... 14-16
MAINTENANCE............................................................................................................17-18
WARRANTY......................................................................................................................... 19

IMPORTANT SAFETY PRECAUTIONS
READ AND SAVE THESE
INSTRUCTIONS CAUTION:
For indoor use only. Do not use to exhaust hazardous or explosive materials and/or vapors.
WARNING
To reduce the risk of fire, electric shock or injury to persons, observe the following:
manufacturer.
 All other servicing should be referred to a qualified technician.
CAUTION:
To reduce risk of fire and to properly exhaust air, be sure to duct air outside - do not vent exhaust air into
spaces within walls, ceilings, attics, crawl spaces, or garages.
Automatically operated device - to reduce risk of injury disconnect from power supply before servicing
CAUTION:
Range hood may have very sharp edges; please wear protective gloves when installing, cleaning or
servicing the unit.
This appliance must be installed by aqualified technician. The manufacturer declines all responsibility
in case of failure to adhere to safety standards. Install this hood in accordance with all the specified
.
 Before servicing or cleaning the unit, switch power off at the service panel and lock the service
disconnecting means stop revent power from being switched on accidentally. If the service
disconnecting means cannot be locked, securely fasten a noticeable warning device, such a tag,
to the service panel.
 Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the
 Follow the heating equipment manufacturer's guide line and safety standards such as those published
by the National Fire Protection Association (NFPA) and the local code authorities.
equipment to preventback-drafting.
 Do not make alterations to the original wiring.
 Do not attempt to repair or replace any part of your hood unless it is specifically recommended in this
manual.
 Sufficientairisneededforpropercombustionandexhaustingofgasesthroughthechimneyoffuelburning
 When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
 Ducted fans must always be vented to the outdoors.
 Installation work and electrical wiring must be done by a qualified person in accordance with all
applicalbe codes & standards, including Fire-rated construction.
4
requirements.

WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A COOKTOP GREASE
FIRE, OBSERVE THE FOLLOWING:
 Smother flames with a close-fitting lid, cookie sheet, or metal tray and then turn off the burner.
 If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
 Never pick up a flaming pan - you may BURN YOURSELF.
 DO NOT USE WATER, including wet dishcloths or towels -a violent steam explosion will result.
 Use an extinguisher ONLY if:
a) You know you have a class ABC extinguisher, and you already know how tooperate it.
b) The fire is small and contained in the area where it started.
c) The fire department has beencalled.
d) You can fight the fire with your back to anexit.
WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
 Never leave a range unattended.
 Boil-overs cause smoke and greasy spillovers that may ignite. Heat oils slowly on low or medium setting.
 Always turn hood ON when cooking at high heat.
 Clean the unit’s surfaces frequently. Grease can accumulate on fan or filters.
 Use proper pan size. Always use cookware appropriate for the size of the surface element.
5













Safety gloves and goggles
Electrical drill
Phillips screwdriver
Flathead screwdriver
Hammer
Adjustable wrench
Sheet metalsheers

PARTS INCLUDE
Needle nose pliers
Scissors (to cut duct tape)
Duct tape
Marker or pencil
Level
Measuring tape
D
INSTALLATION INSTRUCTIONS
TOOLS NEEDED TO INSTALL THE RANGE HOOD
6
Filters
6" Top cover for square
exhaust
3.25" x10" Adapter
connector
Adapter
Qty: 6 pcs
(for drywall only) Qty: 6 pcs

A Floor to ceiling height variable
B
Floor to counter top height
(standard) 36"
C
Recommended height between
cooking surface and bottom of the
hood
28"-30"
D Hood height 9.8"
E Cabinet height N/A
Installation
The information contained herein is based on sources that we believe to be reliable, but is not
guaranteed by us, may be incomplete and/or may change without notice.
DIMENSIONS FOR 36’’ HOOD
Back View
7
Overall View

BEFORE INSTALLING THE HOOD
WALL FRAMING FOR ADEQUATE SUPPORT
THIS VENT HOOD IS HEAVY. ADEQUATE STRUCTURE AND SUPPORT MUST BE PROVIDED IN ALL TYPES OF
INSTALLATION. IF MOUNTING ONTO DRY WALL, IT IS RECOMMENDED THAT THE HOOD BE SECURED TO
VERTICAL STUDS IN THE WALL OR TO A HORIZONTAL SUPPORT.
WARNING
BE CAREFUL WHEN INSTALLING THE HOOD, AS IT MAY HAVE SHARP EDGES. WE RECOMMEND THAT YOU
WEAR PROTECTIVE GLOVES.
CAUTION
DO NOT REMOVE THE PROTECTIVE PLASTIC FILM COVERING THE HOOD AT THIS STAGE.
For the most efficient airflow exhaust, use a straight run or as few elbows as possible.
Vent unit to the exterior only.
At least two people are required for installation.
Remove the range hood from the carton packaging and place on a flat surface for assembly.
CAUTION
THIS APPLIANCE SHOULD BE PROPERLYGROUNDED.
The range hood must be connected with copper wire/plug only.
Make sure the unit is connected to an individual, properly grounded circuit.
If the electrical supply does not meet above requirements, call a licensed electrician before proceeding.
Route house wiring as close as possible to the installation location, in the ceiling or back wall.
The hood must be connected to the house wiring in accordance with the local codes and norms.
8

Venting Requirements Height & Clearance
• Vent system must evacuate to the exterior
(through the roof or side wall).
• DO NOT terminate the vent system in an
attic or other enclosed area.
• Use rigid metal/aluminum ventonly.
• NEVER use plastic vent or plastic vent cover.
• Always keep the duct clean to ensure
proper airflow.
• Calculate the following figures before installation:
Cabinet
heigh
1. Distance from the floor to the ceiling.
2. Distance between the floor and the
countertop/cooking surface.
3. Distance between the range hood
and the countertop/cooking surface
which is recommended at 27” to 30’’.
4. Height of hood and duct cover with
t
Range
hood
height
Range hood
Cabinet
the cabinet.
For the most efficient & quiet operation:
• It is recommended that the range hood be
vented vertically through the roof through
6” (15cm) round metal/aluminum vent or
vented horizontally through the wall through
a rectangular vent measuring 3 ¼’’x10’’.
Ceilin
• The size of the vent should be uniform.
• If venting vertically, do not use more than
three 90° elbows. Do not install two elbows
together.
• Make sure there is a minimum of 24” (61
cm) of straight vent between the elbows if
more than one elbow is used.
• The length of vent system and number of
elbows should be kept to a minimum to
provide efficient performance.
• The vent system must have a damper. If
roof or wall cap has a damper, DO NOT use
damper (if supplied) on top of the range
hood.
• Use duct tape to seal all joints in the vent
system.
• Use caulking to seal exterior wall or roof
opening around the cap.
g
height
36” standard
counter
height
Countertop/Cooking
surfac
Min: 24”
Max: 30”
e
9

• This range hood is factory set for venting throungh the roof or wall.range hood as shown below:
IMPORTANT
•
•
•
Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow may be
needed.
10
•
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or
garages. All exhaust must be ducted to the outside.
Use metal/aluminum duct work only.
VENTING METHODS
INSTALLATION DIAGRAMS
Fasten all connections with sheet metal screws and tape all joints with certifed Silver Tape or Duct Tape.
Use caulking to seal exterior wall or roof opening around the cap.
•
Wall cap
Option 1:
Roof cap
Horizontal venting
Wall cap
Option 2: Vertical venting

WARNING
Three or more persons are required to move and
install this range hood. Spinal or other bodily injuries
could occur if these instructions are not followed.
Risk of severe injury
Rotating fan can cause severe injury.
Stay clear of fan when motor is running.
WARNING
ELECTRICAL REQUIREMENTS AND
INSTALLATION WARNING
THIS RANGE HOOD MUST BE PROPERLY GROUNDED. TURN OFF ELECTRICAL POWER AT SERVICE ENTRANCE
BEFORE WIRING. CHECK TO MAKE SURE THAT THE ELECTRIC CORD IS NOT IN CONTACT WITH THE SHARP
EDGES OF THE APPLIANCE.
IMPROPER GROUNDING CAN RESULT IN A RISK OF ELECTRIC SHOCK. CONSULT A QUALIFIED ELECTRICIAN IF
THE GROUNDING INSTRUCTIONS ARE NOT COMPLETELY UNDERSTOOD OR IF THERE IS DOUBT AS TO
WHETHER THE APPLIANCE IS PROPERLY GROUNDED. DO NOT USE AN EXTENSION CORD. IF THE POWER
SUPPLY CORD IS TOO SHORT, HAVE A QUALIFIED ELECTRICIAN INSTALL AN OUTLET NEAR THE APPLIANCE.
• This appliance must be plugged into an outlet that is properly installed and grounded. In the event of
an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire
for the electric current.
• Position the outlet offset so that the power cord will not interfere with the round duct. Make sure
this does not interfere with the mountingbracket.
ADVANCED PREPARATION
• A straight, short vent run will allow the hood to perform more efficiently. Try to avoid as many
transitions, elbows and long runs as possible. This may reduce the hood’s performance
• Decide on the location of the venting pipe from the hood to the outside.
.
• Use duct tape to seal joints between pipe sections.
• For installing under the cabinet with recessed bottom, attach 4’’ wide wood filler strips (not
provided) on each side. See Figure 1.
CAUTION: If moving the cooking range to install the hood, turn OFF the power at the main electrical box.
SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.
Figure 1Figure 2
• Puncture the knockout holes (for mounting under the cabinet) on the hood as shown in Figure 2.
• If necessary, attach two rubber stands with adhesive tapes to the back corners ofthe hood.
11
• Using references in measurements and installation diagrams (see page 7), create access
opening for electrical wires and hood exhaust under thecabinet.

Figure 3
recommended height may not be applicable
INSTALLATION
Measure the distance between the cooking
surface and the bottom of the range hood. A
distance of 24” to 30” is recommended*.
*Due to different ceiling height configurations, the
.
A. Determine the venting method and proceed if you would like tovent VERTICALLY.
1. Using references in the Height & Clearance diagram, determine and clearly mark the centerline
on the bottom of the cabinet.
2. Draw electrical wires through cabinet access opening on top of the range hood (refer to figure 3),
center the hood beneath the cabinet and flush with the front of the cabinet.
3. From inside the hood, place hood mounting screws in the exact center of each knockout holes and
CAUTION: Make certain the range hood is secure before releasing!
B. Determine the venting method and proceed if you would like tovent HORIZONTALLY.
1. Using references in the Height & Clearance diagram, determine and clearly mark a centerline
on the wall.
12
secure to the cabinet bottom. Tighten all screws until secure. Be careful when using electrical
screwdriver in order not to damage the range hood. Connect and securethe metal duct(referto
figure4). Skip Part B below and proceed to Step 2..
Step 1: You have two options for installing this range hood (see INSTALLATION DIAGRAMS on page 7):
Figure 4
2-1. Draw electrical wires through cabinet access opening on top of the range hood (refer to figure 3),
secure to the cabinet bottom. Tighten all screws until secure. Be careful when using electrical
screwdriver in order not to damage the range hood. Connect and securethe metal duct(referto
center the hood beneath the cabinet and flush with the front of the cabinet.
3-1. From inside the hood, place hood mounting screws in the exact center of each knockout holes and
figure5).
Use aluminum foil tape to
make all joints secure and
air tight.
Figure 5

INSTALLATION (continued)
Step 4: Turn power ON in control panel. Check all lights and fan operations.
13
2-2. Draw electrical wires through cabinet access opening on back of the range hood (refer to
Step 2:
For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more
secure installation, use as many mounting holes as needed to secure from the inside of hood.
Step 3:
Angle filter and direct tab inserts toward the aft slot of the range hood opening. While continuing to install the
filter, ensure you lift the lever for the retractable tabs to clear way for flush insertion. When filter sits flush within
the opening, release the lever to lock in place(refer figure 8).
figure 6),
center the hood beneath the cabinet and flush with the front of the cabinet.
3-2. From inside the hood, place hood mounting screws in the exact center of each knockout
secure to the cabinet bottom. Tighten all screws until secure. Be careful when using electrical
screwdriver in order not to damage the range hood. Connect and securethe metal duct(referto
figure7).
holes and
Figure 6
Figure 7
Retractable Tabs
Tab Inserts
Lift Lever
Figure 8

Control Panel Layout and Buttons Configurations:
RANGE HOOD OPERATIONS
14
Decrease Value
Power
Power-Off Delay Clock/ Digital Display
Light
Increase Value Digital
BUTTON FUNCTIONS:
•Power: Power ON/OFF the range hood and activate power-of delay timer.
•Decrease Value: Blower (motor) speed decrease, timer value decrease, and enter timer mode.
•Increase Values: Blower (motor) speed increase, timer value increase, and cleaning reminder reset.
•Digital Display: Display current time when motor is OFF. Shows current blower (motor) speed (F1-F3)
•Light: Turns ON/OFF lights.
CONTROLS:
•Adjusting the blower (motor) speed:
•Press Power button once to turn on the system. The Digital Display shows theblower(motor) speed
level.
Press Decrea se Value button will decrease the speed of the blower (motor) from F3 to F1 (strongest
to quietest). Press Increase Value button will increase the speed of the blower (motor) from F1 to F3
(quietest to strongest).
•Adjusting the delay timer function:
Three-Minute Delay Power-Of
•While the fans are running, press Power button once to enter Power-Of Delay Timer mode, the Digital
Display will fash and blower (motor) will turn of after 3 minutes.
•During this 3 minutes delay, changing speeds will not afect the countdown.
•The 3 minute Power-Of Delay Timer function can be cancelled by pressing Power button once.
•Immediate Power-Off
•When the fans are operating in normal mode (Power-Of Delay Timer inactivated), rapidly press the
Power Control (On/Of) button twice to turn of the blower (motor).
•Lights:
•Press Light button once to turn on the lights, and once again to turn of the lights.

Noise Level (dB / sone)
Number Of Motors
Motor Type
Fan Type
Control Type
Filtration Type
Illumination
Venting Size
Interference Protection
3
120W(60W+60W)
Leves
1.5A
126W
2 Motors
Seamless Stainless Steel, Satin Finish
Single Chamber Ultra Quiet
1.0Sone(40dB) / 2.8Sone(55dB) / 5.3Sone(64dB)
Centrifugal Squirrel Cage
Touch Sensitive Electronic Control Panel
Stainless Steel Baffle Filter
3W 12V LED Light
6 inches Round (Top); 3-1/4 x 10 inches Rectangular (Top & Rear)
Radio Frequency Interference Protected
SPECIFICATIONS
Specifications3:
1. In House Test Static Pressure “0”.
2. One sone is roughly equivalent to the sound of a refrigerator (1kHz) at 40 decibels.3.
Subject to change without notice, please contact your local reseller for details.
CIRCUIT DIAGRAM
Body Design
Power Rating
General Input Power
Motor Input Power
Ampere
Levels Of Speed Control
Airflow(Max)
15
220-240V/50Hz
560CFM

RANGE HOOD ASSEMBLY
No.
1
2
3
4
5
6
7
8
9
10
Quantity
Power Cord
6-inch Round Duct Connector
Square Duct Plate
Square Duct Connector
Hood Body
Control Panel
LED Light
Lid of Plastic box
Main Circuit Board
1
1
1
1
1
1
2
1
1
1
Capacitor
16
Description
Protective Panel
Motor
Fan blade
Protective Cover
11
12
13
14
15
16
Plastic box
Baffle Filter
1
1
2
2
2
3

MAINTENANCE
SAFETY WARNING: NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN
For optimal operation, clean range hood, surfaces and filters regularly. Regular care will help preserve the
appearance of the range hood.
CLEANING THE EXTERIOR SURFACES
Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent or
steel wool pads, which will scratch and damage the stainless-steel surface. For heavier soil, use a liquid
degreasing cleaner. Use a stainless-steel cleaner to clean the surface of the hood. Avoid getting cleaning
solution onto or into the control panel. Follow directions of the stainless-steelcleaner.
CAUTION
USE SOFT TOWEL TO WIPE OFF THE CLEANING SOLUTION, GENTLY RUB OFF ANY STUBBORN SPOTS. USE DRY SOFT
TOWEL TO DRY THE HOOD. ALWAYS SCRUB LIGHTLY WITH CLEAN COTTON CLOTH AND IN THE DIRECTION OF
THEGRAIN.
DO NOT ALLOW DEPOSITS TO ACCUMULATE OR REMAIN ON THE HOOD. DO NOT USE ORDINARY STEEL WOOL OR
STEEL BRUSHES. SMALL BITS OF STEEL MAY ADHERE TO THE SURFACE AND CAUSE RUSTING.
DO NOT ALLOW SALT SOLUTIONS, DISINFECTANTS, BLEACHES OR CLEANING COMPOUNDS TO REMAIN IN CONTACT
WITH STAINLESS STEEL FOR EXTENDED PERIODS. MANY OF THESE COMPOUNDS CONTAIN CHEMICALS, WHICH MAY
BE HARMFUL. RINSE WITH WATER AND WIPE DRY WITH A CLEAN CLOTH.
CLEANING THE GREASE FILTER
The filters are intended to filter out residue and grease from cooking and are required to be kept clean.
Filters should be cleaned after every 30 hours of use (or once a month, depending on use). Remove and
clean by hand in soapy water or in the dishwasher. Dry filters and re-install. If cleaning the filters in the
dishwasher, use a non- phosphate detergent. The use of detergent with phosphate may cause discoloration
of the filters but will not affect their performance. This discoloration is not covered by thewarranty.
REPLACING THE FILTERS
If filters wear out due to prolonged use, please contact your service/parts provider for replacement filters.
NOTE: ALSO REPLACE DAMAGED FILTER THAT HAS PUNCTURED OR BROKEN MESH, BENT OR BROKEN FRAME.
CLEANING THE STAINLESS-STEEL SURFACE
Regularly wash surface with dry cloth or clean cloth soaked in warm water and mild soap or liquid dish
detergent. Always clean following the grain. Always rinse thoroughly with clear water (2-3 times) and wipe
dry completely. Specially designed stainless-steel cleaners can also be used.
GREASE CUP
Take good care of installing the grease tunnel properly and to empty and clean it on a regular basis.
17

REPLACING THE LED LIGHT BULBS
CAUTION: LED lamps can only be replaced with a new LED lamp. The lamp rating must be equal to the one
already used. Make sure all the control switches are off and the hood is unplugged, or the breaker is OFF.
Replacing the LED light fixture:
• Make sure the range hood is unplugged or turn OFF breaker and make sure the lights are cool to touch.
• Place a flat-head screwdriver between light housing and hood body, gently pry up the light
housing and search for the metalclip.
• Apply force to the metal clip and pull out the light fixture. Disconnect the power cable and discard
the old light fixture.
• Reverse the steps to install a new LED light fixture. Turn ON breaker and range hood to test for operation.
• This range hood uses LED light fixture: 3W Max 12V LED
18

Contact Us
If you need any assistance, please contact your local reseller. Please have your order number and model of the
range hood ready. This information will help them better respond to your request.
If you need replacement parts, we recommend that you only use genuine parts. Our accessories and parts are
engineered and designed specifically for this series of range hood, each is rigorously tested assuring the utmost
in durability and reliability, providing a factory match, factory-installed appearance and functionality tailored to
SERVICE AND WARRANTY
LIMITED WARRANTY
One Year Parts Warranty:
For one year from the date of original purchase, your local reseller will provide free of charge, non-consumable
replacement parts or components that failed due to manufacturing defects. Subject to the conditions and limitations
set forth below, your local reseller will, at its option, either repair or replace any part of its products that prove
defective by reason of improper workmanship or materials. Repaired parts or replacement products will be provided
by your local reseller on an exchange basis, and will be either new or refurbished to be functionally equivalent to new.
The consumer is responsible for all shipping costs. Consumable parts not covered by this warranty include but not
limited to: Light bulbs, metal and control panel.
Who is Covered:
This warranty is extended to the original purchaser for products purchased for indoor use.
This Warranty Will Be Voided When:
Product damaged through negligence, improper installation, accident, abuse, misuse, natural disaster, insufficient or
excessive electrical supply, abnormal mechanical or environmental conditions, or any unauthorized disassembly,
repair, modification, or failure to follow installation instructions. When product is used commercially or other than its
intended purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or
modified by anyone other than your local reseller’s authorized agents. This limited warranty also does not apply to any
product on which the original identification information has been altered, obliterated or removed, has not been handled
or packaged correctly or has been sold as second-hand.
What is Not Covered:
Consumable parts such as light bulbs, metal and control panel. The natural wear of finish, and wear due to improper
maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner products. Chips, dents or cracks
due to abuse, misuse, freight damage, or improper installation. Damage of product caused by accident, fire, floods or
act of God. The manufacturer and/or distributor/reseller is not liable for, and does not cover under warranty, any loss
ofproperties or any costs associated with removing, servicing, installing, or determining the source of problems with
this product.
This warranty is valid in the country of the original purchase at retail. It is non-transferable and applies only to the
original purchaser and does not extend to subsequent owners of this product. Any applicable implied warranties,
including the warranty of merchantability, are limited in duration to a period of express warranty as provided herein
beginning with the date of original purchase at retail and, no warranties, whether express or implied, shall apply to this
product thereafter.
To obtain warranty service, you may contact your local reseller from which you purchased this product. Please confirm
the terms of your local reseller’s policies prior to contacting. Typically, you must include product identification infor-
mation, including model number and serial number with a detailed description of the problem you are experiencing.
You must also include proof of the date of original retail purchase as evidence that the product is within the applicable
warranty period.
each individual range hood model.
19