ADJ ADJ-610 User manual

User Instructions

1
CONTENTS
1. SafetyInstructions............................................................................................................................2
2. TechnicalSpecifications....................................................................................................................4
3. ControlPanel....................................................................................................................................5
4. Howtosetthefixture......................................................................................................................6
4.1Menu..............................................................................................................................................6
4.2OffsetAdjust.................................................................................................................................10
5. ControlbyDMX512controller......................................................................................................12
5.1DMXConnection..........................................................................................................................12
5.2DMXAddressSetting....................................................................................................................12
5.3DMXConfiguration.......................................................................................................................13
6. Troubleshooting.............................................................................................................................26
7. FixtureCleaning.............................................................................................................................27

2
1. SafetyInstructions
WARNING
PleasekeepthisUserGuideforfutureconsultation.Ifyouselltheunittoanotheruser,besure
thattheyalsoreceivethisinstructionbooklet.
Unpackandcheckcarefullythereisnotransportationdamagebeforeusingtheunit.
Beforeoperating,ensurethatthevoltageandfrequencyofpowersupplymatchthepower
requirementsoftheunit.
It’simportanttogroundtheyellow/greenconductortoearthinordertoavoidelectricshock.
Theunitisforindooruseonly.Useonlyinadrylocation.
Theunitmustbeinstalledinalocationwithadequateventilation,atleast50cmfromadjacent
surfaces.Besurethatnoventilationslotsareblocked.
Disconnectmainpowerbeforereplacementorservicing.
Makesuretherearenoflammablematerialsclosetotheunitwhileoperatingasitisfirehazard.
Usesafetycablewhenfixesthisunit.DONOThandletheunitbytakingitsheadonly,butalways
bytakingitsbase.
MaximumambienttemperatureisTa:40℃.DONOToperateitwherethetemperatureishigher
thanthis.
Unitsurfacetemperaturemayreachupto75℃.DONOTtouchthehousingbare‐handduringits
operation.Turnoffthepowerandallowabout15minutesfortheunittocooldownbefore
replacingorserving.
Intheeventofseriousoperatingproblem,stopusingtheunitimmediately.Nevertrytorepair
theunitbyyourself.Repairscarriedoutbyunskilledpeoplecanleadtodamageormalfunction.
Pleasecontactthenearestauthorizedtechnicalassistancecenter.Alwaysusethesametype
spareparts.
DONOTtouchanywireduringoperationashighvoltagemightbecausingelectricshock.
Pleasereadcarefullytheinstruction,whichincludesimportant
informationabouttheinstallation
,
usa
g
eandmaintenance.

3
Warning:
Topreventorreducetheriskofelectricalshockorfire,donotexposetheunittorainor
moisture.
DONOTopentheunitwithinfiveminutesafterswitchingoff.
Thehousing,thelenses,ortheultravioletfiltermustbereplacediftheyarevisiblydamaged.
Caution:
Therearenouserserviceablepartsinsidetheunit.DONOTopenthehousingorattemptany
repairsyourself.Intheunlikelyeventyourunitmayrequireservice,pleasecontactyournearest
dealer.
Installation:
Theunitisfullyoperationalinthreedifferentmountingpositions,hangingupside‐downfroma
ceilingorsetonaflatlevelsurface.Toavoidinternaldamagetotheunit,nevermounttheuniton
itssideasillustratedabove.Besurethisfixtureiskeptatleast0.5mawayfromanyflammable
materials(decorationetc.).Alwaysuseandinstallthesuppliedsafetycableasasafetymeasureto
preventaccidentaldamageand/orinjuryintheeventtheclampfails.

4
1. BolteachclamptotheOmegaholderwithscrewandlocknutthroughtheholeintheholder.
2. Fastertheomegaholdersonthebottomofthebasebyinsertingquick‐lockfastenersintothe
holesofthebaseandtightenfullyclockwise.
3. Hangthefixturetothesupportthroughclampandfasterthescrews,Fasterthesafetycable
throughthebottomofthebaseandoverthesupport.
2. TechnicalSpecifications
DMXChannels:15/17channelsmode
LCDdisplayforeasynavigation
Perfectforstage,theatre,TVstudio,rentalanddiscotheques
Voltage: AC100~240V,50/60Hz
Powerconsumption: 199W
LED: OSRAMSIRIUSHRI100W
Fuse:
PowerCordDaisyChain:
T5Amp
8Fixtures(120V/60Hz);16Fixtures(230V/50Hz)
BeamAngle: 3Degree
Dimension: 279x225x387mm
Weight: 9.2Kgs

5
3. ControlPanel
1. Button:
MENUToselecttheprogrammingfunctions
DOWNTogoforwardintheselectedfunctions
UPTogobackwardintheselectedfunctions
ENTERToconfirmtheselectedfunctions
2. Microphone:Toreceivemusicforsoundactive;
3. LED:
POWEROnPowerOn
DMXOnDMXinputpresent
4. FunctionDisplay:Usedtoshowthevariousmenusandtheselectedfunction;
5. IRReceiver:ToreceivetheIRsignal;
6. Fuse:Protectstheunitfromover‐voltageorshortcircuit;
7. PowerIn/out:Usedtoconnecttosupplypower.
8. DMXIn/out:Waterproofcablewith3‐pinXLRconnectorsforDMX512operation;

6
4. Howtosetthefixture
4.1Menu
Toselectanyofthegivenfunctions,presstheMENUbuttonuptowhentherequiredoneis
showingonthedisplay.SelectthefunctionbytheENTERbuttonandthedisplaywillblink.Usethe
DOWNandUPbuttontochangethemode.Oncetherequiredmodehasbeenselected,pressthe
ENTERbuttontosetup,togobacktothefunctionswithoutanychangepresstheMENUbutton
again.HoldandpresstheMENUbuttonaboutonesecondorwaitforoneminutetoexitthemenu
mode.
Themainfunctionsareshowingbelow:

7
DMXAddress
PresstheMENUbuttonuptowhentheDMXAddressisshownonthedisplay.PressingENTER
buttonandthedisplaywillblink.UseDOWNandUPbuttontochangethevalue.Oncetheaddress
hasbeenselected,pressENTERbuttontosetuporautomaticallyexitmenumodewithoutany
changeafter10seconds.BacktothepreviousfunctionswithoutanychangepressMENUbutton.

8
ChannelMode
PresstheMENUbuttonuptowhentheChannelModeisshownonthedisplay.Pressingthe
ENTERbutton.UseDOWNandUPbuttontoselectthe15Chanor17Chanmode.Onceselect,
presstheENTERbuttontosetuporautomaticallyexitmenumodewithoutanychangeafter10
seconds.TogobacktothefunctionswithoutanychangepresstheMENUbutton.
ShowMode
PresstheMENUbuttonuptowhentheShowModeisshownonthedisplay.PressingtheENTER
button.UseDOWNandUPbuttontoselecttheShow1,Show2,Show3orShow4mode.Once
select,presstheENTERbuttontosetuporautomaticallyexitmenumodewithoutanychange
after10seconds.TogobacktothefunctionswithoutanychangepresstheMENUbutton.
SlaveMode
PresstheMENUbuttonuptowhentheSlaveModeisshownonthedisplay.PressingtheENTER
button.UseDOWNandUPbuttontoselecttheMaster,Slave1orSlave2.Onceselect,pressthe
ENTERbuttontosetuporautomaticallyexitmenumodewithoutanychangeafter10seconds.To
gobacktothefunctionswithoutanychangepresstheMENUbutton.
DMXLastState
PresstheMENUbuttonuptowhentheDMXLastStateisshownonthedisplay.PresstheENTER
button,useDOWNandUPbuttontoselecttheMasterSlave,BlackoutorLastState.Onceselect,
pressENTERbuttontostoreorautomaticallyexitmenumodewithoutanychangeafter10
seconds.TogobacktothefunctionswithoutanychangepresstheMENUbutton.
SoundState
PresstheMENUbuttonuptowhentheSoundStateisshownonthedisplay.PressingENTER
button,UseDOWNandUPbuttontoselecttheOnorOff.Onceselect,pressENTERbuttonto
setuporautomaticallyexitmenumodewithoutanychangeafter10seconds.Togobacktothe
functionswithoutanychangepresstheMENUbutton.
SoundSense
PresstheMENUbuttontoshowSoundSenseonthedisplay.PresstheENTERbuttonandthe
displaywillblink.UsetheDOWNandUPbuttontoadjustthevaluefrom0to100,pressthe
ENTERbuttontosetup,togobacktothefunctionswithoutanychangepresstheMENUbutton
again.HoldandpresstheMENUbuttonaboutonesecondorwaitforoneminutetoexitthemenu

9
mode.
PanInvert
PresstheMENUbuttonuntilPanInvertisshowingonthedisplay.PressingtheENTERbuttonand
thedisplaywillblink.UsetheDOWNandUPbuttontoselecttheNoorYes,presstheENTER
buttontoconfirmorautomaticallyreturntothemainfunctionswithoutanychangeafter8
seconds.TogobacktothefunctionswithoutanychangepresstheMENUbuttonagain.
TiltInvert
PresstheMENUbuttonuntilTiltInvertisshowingonthedisplay.PressingtheENTERbuttonand
thedisplaywillblink.UsetheDOWNandUPbuttontoselecttheNoorYes,presstheENTER
buttontoconfirmorautomaticallyreturntothemainfunctionswithoutanychangeafter8
seconds.TogobacktothefunctionswithoutanychangepresstheMENUbuttonagain.
BackLight
PresstheMENUbuttonuntilBackLightisshowingonthedisplay.PressingtheENTERbuttonand
thedisplaywillblink.UsetheDOWNandUPbuttontoselecttheOfforOn,presstheENTER
buttontoconfirmorautomaticallyreturntothemainfunctionswithoutanychangeafter8
seconds.TogobacktothefunctionswithoutanychangepresstheMENUbuttonagain.
AutoTest
PresstheMENUbuttonuptowhentheAutoTestisblinkingonthedisplay.PresstheENTER
buttonandtheunitwillrunthebuilt‐inprogrammerforself‐test.Togobacktothefunctionspress
theMENUbutton.
FixtureTime
PresstheMENUbuttonuptowhentheFixtureTimeisblinkingonthedisplay.PresstheENTER
buttonandthedisplaywillshowthenumberofworkinghoursoftheunit.Togobacktothe
functionspresstheMENUbutton.
LampTime
PresstheMENUbuttonuptowhentheLampTimeisblinkingonthedisplay.PresstheENTER
buttonandthedisplaywillshowthenumberofworkinghoursofthelamp.PresstheENTERbuton
andusetheDOWNandUPbuttontoselecttheExitorResetTime.Togobacktothefunctions
presstheMENUbutton.
LampOn