ADJ FOCUS WASH 400 User manual

User Manual
FOCUS WASH 400
US SKU#: FOC615
EU SKU#: 1237000240
ITF-14#: 818651029130

©2021 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade-
marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-
tion of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 2
Date Document
Version
Software
Version DMX Channels Notes
05/05/2021 1.0 1.1.1 16 / 21 / 23 ch Initial Release
06/25/2021 2.0 1.1.2 17 / 22 / 24 / CMY 18 /
CMY 24 ch
Update DMX Traits, System Menu,
added Color Swatch Table, add
Snoot and Linear Lens Installation
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update of this manual
before beginning installation and/or programming.

TABLE OF CONTENTS
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 3
General Information 4
Key Features | Warranty Returns 5
Limited Warranty (USA Only) 6
Safety Guidelines 7
Overview 8
DMX Set Up 9
Installation 11
Control Panel 17
System Menu 18
DMX Addressing 22
DMX Traits 23
Color Macros Chart 30
Color Temperature Chart 31
Dimmer Modes & Curves 32
Cleaning & Maintenance 33
Fuse Replacement | Software Updates 34
Dimensional Drawings 35
Specifications 36

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 4
Introduction: Congratulations on your purchase of the ADJ Focus Wash 400! This device is a 400W,
RGBACL (Red, Green, Blue, Amber, Cyan, Lime), LED moving light wash, and has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and understand
the instructions in this manual carefully and thoroughly before attempting to operate this device. These
instructions contain important information regarding safety during use and maintenance.
Please keep this manual with the device for future reference.
Customer Support: Contact ADJ Service for any product related service and support needs. Also visit
forums.adj.com with questions, comments or suggestions.
Parts: To purchase parts online visit:
http://parts.adj.com (US)
http://www.adjparts.eu (EU)
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 | Fax: [phone] | [email protected]
ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] | Fax: [phone] | [email protected]
ADJ PRODUCTS LLC USA
6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax [phone] | www.adj.com | [e-mail]
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]
www.adj.eu | [email protected]
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone]
WARNING! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,
please contact ADJ Products, LLC.
Do not discard the shipping cartoon in the trash. Please recycle when ever possible.
GENERAL INFORMATION

KEY FEATURES
• 400W RGBACL LED
• 10 to 46-degree motorized zoom
• Flicker free operation for TV and film
• 16-bit pan/tilt movement
• RGBACL color mixing
• Variable dimming modes/curves and strobe effects
• DMX and RDM protocol support
• DMX and power in/out connections
• LCD menu display with 6 button control panel
• Multiple unit power linking
• Multi-voltage universal auto switching power supply (AC100-240V)
INCLUDED ITEMS:
• Twist-lock power cable (x1)
• Omega brackets (x2)
• Snoot (x1)
• Linear Lens (x1)
• Screws (x4)
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 5
WARRANTY RETURNS
All returned service items,whether under warranty or not, must be freight pre-paid and accompanied
by a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the
return package. A brief description of the problem as well as the R.A. number must also be written
down on a piece of paper included in the shipping carton. If the unit is under warranty, you must pro-
vide a copy of your proof of purchase invoice. You may obtain anR.A. number by contacting our cus-
tomer support team. All packages returned to the service department not displaying anR.A. number
on the outside of the package will be returned to the shipper.

LIMITED WARRANTY (USA ONLY)
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 6
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of
manufacturing defects in material and workmanship for a prescribed period from the date of purchase
(see specic warranty period on reverse). This warranty shall be valid only if the product is purchased
within the United States of America, including possessions and territories. It is the owner’s responsibility
to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product
back—please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to
the ADJ Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service
(including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return ship-
ping charges only to a designated point within the United States. If the entire instrument is sent, it must be
shipped in its original package and packaging material. No accessories should be shipped with the prod-
uct. If any accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever
for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is
modied in any manner which ADJ Products, LLC concludes, after inspection, aects the reliability of the
product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory
unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is dam-
aged because it was not properly maintained as set forth in the product instructions, guidelines and/or
user manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic
checkup. During the period specied above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason
of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty
shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion
of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012,
and bear identifying marks to that eect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or tness,
are limited in duration to the warranty period set forth above. And all warranties, whether expressed or
implied, including warranties of merchantability or tness, are limited in duration to the warranty period set
forth above. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is ex-
pressly provided above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or
damage, direct and/or consequential arising out of the use of, and/or inability to use this product.
G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all
prior warranties and written descriptions of warranty terms and conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Non-LED Lighting Products = 1-Year (365 Days) (Including Special Eect Lighting, Intelligent Lighting,
UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands,
Power/Data Distribution, etc. excluding LED and lamps)
• Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)
• LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)
• NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States.
StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)
• ADJ DMX Controllers = 2 Year (730 Days)
• American Audio Products = 1 Year (365 Days)

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 7
SAFETY GUIDELINES
For Your Own Personal Safety, Please Read and Understand This Manual Completely Before
You Attempt To Install Or Operate This Unit!
• Be sure to save the packing carton in the unlikely event the device may have to be returned for
service
• Do not spill water or other liquids into or on to the device
• Be sure that the local power outlet matches the required voltage for the device
• Do not open up the device for any reason. There are no user serviceable parts inside
• Disconnect the device’s main power when left unused for long periods of time
• Never connect this device to a dimmer pack
• Do not attempt to operate this device if it has been damaged in any way
• Never operate this device with the cover removed
• To reduce the risk of electrical shock or re, do not expose this device to rain or moisture
• Do not attempt to operate this device if the power cord has been frayed or broken.
• Do not attempt to remove or break o the ground prong from the electrical cord. This prong is used
to reduce the risk of electrical shock and re in case of an internal short
• Disconnect from main power before making any type of connection
• Never block the ventilation holes. Always be sure to mount this device in an area that will allow
proper ventilation. Allow about 6” (15cm) between this device and a wall
• This unit is intended for indoor use only. Use of this product outdoors voids all warranties
• Always mount this unit in a safe and stable matter
• Please route your power cord out of the way of foot trac. Power cords should be routed so they
are not likely to be walked on, or pinched by items placed upon or against them
Maximum ambient operating temperature for this xture is 113 degrees F (45 degrees C). Do not
operate this device when ambient temperature exceeds this value!
Keep ammable materials away from this xture!
FIXTURE IS DESIGNED FOR INDOOR USE ONLY! DO NOT EXPOSE TO RAIN OR MOISTURE!
The device should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen on, or liquid has been spilled into, the device.
C. The device has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 8
OVERVIEW
1. Display Screen
2. Left Button
3. Down Button
4. Enter Button
5. Right Button
6. Up Button
7. Carry Handle (x2)
8. Mode Button
9. Service Port
10. Power In
11. Power Out
12. DMX In, 3-pin
13. DMX In, 5-pin
14. DMX Out, 3-pin
15. DMX Out, 5-pin
16. Fuse
17. Mounting Clamp Attachment (x4)
18. Safety Cable Attachment

DMX SET UP
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-
nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions
from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be
linked together and operate from a single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible
when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed
anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Wash 400 can be con-
trolled via DMX-512 protocol. The DMX address is set on the front panel of the fixture. Your unit and
your DMX controller require a standard 3-pin XLR connector for data input and data output. We rec-
ommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-
120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables
should be made with a male XLR connector at one end and a female XLR connector on the other.
Also remember that DMX cable must be daisy chained and cannot be split.
Notice: Be sure to follow figures 1 and 2 when making your own cables. Do not use the ground lug
on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the
shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a
short circuit and may result in erratic behavior.
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 9

DMX SET UP
Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter-
minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor
which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is
inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a
cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-
mission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When insert-
ing standard 5-pin data cables into a 3-pin line, a cable adaptor must be used. These adaptors are
readily available at most electronics stores. The chart below details a proper cable conversion.
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 10

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 11
INSTALLATION
IP RATING
This device is IP30 rated. It is protected against instrusion of solids larger than 2.5mm in size, such
as tools and thick-gauge wires. The device is NOT protected against liquid instrusion of any
kind.
FLAMMABLE MATERIAL WARNING!
Keep device a minimum of 5.0 feet (1.5m) away from ammable material and/or pyrotechnics.
ELECTRICAL CONNECTIONS
A qualied electrician should be used for all electrical connections and/or installations.
MULTI-DEVICE DAISY CHAINING
• When connected to 240V power, up to 3 devices may be daisy chained together.
• When connected to 110V power, daisy chaining is NOT permitted. In this situation, only
operatethextureasasinglestandalonedevice!
DO NOT INSTALL THE DEVICE IF YOU ARE NOT QUALIFIED TO DO SO!
The unit MUST be installed following all local, national, and country commercial electrical and con-
struction codes and regulations.
Before installing or mounting any device, a professional equipment installer MUST be consulted to
determine whether the mounting structure or surface is properly certied to safely support the com-
bined weight of the xture, clamps, cables, and accessories.
Overhead xture installations must always be secured with a secondary safety attachment, such as
an appropriately rated safety cable that meets all local, national, and country codes and regulations.
Maximum ambient operating temperature is 113°F (45°C). Do not operate this device when ambient
temperature exceeds this value.
This xture should be installed in areas outside walking paths, seating areas, and areas where unau-
thorized personnel might be able to reach the device by hand.
NEVER stand directly below the xture when rigging, removing, or servicing.
Allow approximately 15 minutes for the xture to cool down before servicing.

INSTALLATION
POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS
External sources of light beams from direct sunlight, lighting moving head fixtures, and lasers which
are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ
lighting fixtures can cause severe internal damage including burning of optics, dichroic color filters,
glass and metal gobos, prisms, animation wheels, frost filters, irises, shutters, motors, belts, wiring,
discharge lamps, and LEDs.
This issue is not unique to ADJ lighting fixtures; it is a common issue with lighting fixtures from all
manufacturers. Although there is no true way to fully prevent this issue from happening, the guide-
lines below can reduce the risk of any potential damage if followed. Contact ADJ Service for more
details.
DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM
DIRECT SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS DURING
UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS
A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 12

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 13
INSTALLATION
CLAMP INSTALLATION
This fixture features multiple mounting clamp attachment points, as well as a safety cable attach-
ment point, located on the bottom face of the fixture (see the illustration below). When mounting the
fixture to a truss or any other suspended or overhead installation, be sure to secure appropriately
rated clamps (not included) to the clamp attachment points and attach a separate SAFETY CABLE
of the appropriate safety rating to the safety cable rigging point.
SAFETY CABLE
ALWAYS ATTACH A SAFETY
CABLE WHENEVER INSTALLING
THIS FIXTURE IN A SUSPENDED
ENVIRONMENT TO ENSURE
THAT THE FIXTURE WILL NOT
FALL IF THE CLAMP FAILS.
RIGGING
Overhead rigging requires extensive experience, including but not limited to: calculating working
load limits, understanding the installation material being used, and periodic safety inspection of all
installation material and the fixture itself. If you lack these qualifications, do not attempt to perform
the installation yourself. Improper installation can result in bodily injury.

INSTALLATION
NOTICE: The max suitable enviromental temperature for this lighting fixture is 45˚C. Do not place
this lighting fixture in an environment where the temperatures exceed this rating. This will allow the
fixture to run at its best and help prolong the fixture life.
The Focus Wash 400 is fully operational in three different mounting positions: hanging upside-down
from a ceiling or trussing, sideways on trussing, or set on a flat level surface. Be sure this fixture is
kept at least 12m (40ft) away from any flammable materials (decoration etc.). Always use and install
a safety cable (not included) as a safety measure to prevent accidental damage and/or injury in the
event the clamp fails. Never use the carrying handles for secondary attachment.
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 14

INSTALLATION
SNOOT INSTALLATION: This device can be fitted with a removable snoot, which can be installed by
following the directions below.
1. Find the four (4) mounting holes located
around the frame of the lens.
2. Align the mounting tabs on the snoot with the
mounting holes on the frame of the lens.
3. Use a screwdriver to insert and tighten
screws into each of the mounting tabs. 4. Installation is now complete!
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 15

INSTALLATION
LINEAR LENS INSTALLATION: This device can be fitted with a linear lens, which can be installed
by following the directions below.
1. Find the four (4) mounting holes located
around the frame of the fixture lens.
2. Align the mounting tabs on the linear lens with
the mounting holes on the fixture lens.
3. Use a screwdriver to insert and tighten
screws into each of the mounting tabs. 4. Installation is now complete!
ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 16

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 17
CONTROL PANEL
This fixture includes an easy to navigate control panel display, from which all necessary settings and
adjustments can be made. During normal operating, pressing the MODE button once will access
the fixture’s main menu. Once in the main menu, the UP and DOWN buttons can be used to navi-
gate through the different functions. Press the ENTER button to select the option displayed on the
screen, and use the LEFT and RIGHT buttons to adjust the settings for the selected option. Press
the ENTER button once more to confirm the setting. Pressing the MODE button at any time to return
to the main menu without making any adjustments.
System Menu Access: To access the system menu when the fixture is not running on the inter-
nal battery, press and hold the MODE button to illuminate the display screen until the DMX
address is displayed. Then navigate to the desired system menu.

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 18
SYSTEM MENU
DMX SETTINGS
DMX Address 001 ~ 512
DMX Channel
Mode
Basic
Standard
Extended
CMY St.
CMY Ext.
No DMX Status
Hold Last Fixture adheres to most recent setting
Hold Last 2 Fixture adheres to most recent setting and
Zoom will return to 0
Blackout Fixture goes into standby mode
Manual Fixture reverts to manual mode settings
PERSONALITY
Primary On / Off
Secondary On / Off
Status Settings
Pan Degree 630 / 540
Pan Invert On / Off
Tilt Invert On / Off
P/T Feedback On / Off
P/T Speed Speed 1 / Speed 2
Hibernation Off, 1min ~ 99 min
Default 15 min
Fan Settings Head
Auto
High
Low
Dim Modes
Standard
Stage
TV
Architectural
Theatre
Stage 2
Dim Speed 0.1 s ~ 10 s
LED Refresh Rate
900 ~ 1500 Hz
Default = 1200 Hz
2500 Hz
4000 Hz
5000 Hz
CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 19
SYSTEM MENU
PERSONALITY
(cont’d from prev
page)
LED Refresh Rate
(cont’d from prev
page)
6000 Hz
Default = 1200 Hz
10 kHz
15 kHz
20 kHz
25 kHz
Dim Curve
Linear
Square
Inv Squa
S Curve
Reset Motors
Reset All Motors Yes / No
Pan/Tilt Reset Yes / No
Effect Reset Yes / No
Display
Intensity 1 ~ 10
Display Invert Yes / No
Screen Saver Delay Off ~ 10 min Default = 5 min
Key Lock Off / On / On1
Service Passcode = 050
Effect Adjust
(Calibration)
Pan
-128 ~ 127
Tilt
-128 ~ 127
...
USB Port Power Off / On
Update Software Off / On
Factory Restore Off / On
Passcode = 011
CONTINUED ON NEXT PAGE

ADJ Products, LLC - www.adj.com - Focus Wash 400 User Manual Page 20
SYSTEM MENU
MANUAL
Pan 000 ~ 255
Pan Fine 000 ~ 255
Tilt 000 ~ 255
Tilt Fine 000 ~ 255
... 000 ~ 255
INTERNAL
PROGRAMS
Program 1 Speed 000 - 255
Fade 000 - 255
Program 2 Speed 000 - 255
Fade 000 - 255
Program 3 Speed 000 - 255
Fade 000 - 255
Program 4 Speed 000 - 255
Fade 000 - 255
Program 5 Speed 000 - 255
Fade 000 - 255
Program 6 Speed 000 - 255
Fade 000 - 255
Program 7 Speed 000 - 255
Fade 000 - 255
INFORMATION
Fixture Life Time
Power On Time
P-On Time-R
(Power On Resettable Time)
P-On Time-Reset
(Power On Time
Reset)
Passcode = 050
Total LED Time
LED On Time
LED On Time-R
LED Hours Reset Passcode = 050
CONTINUED ON NEXT PAGE