ADJ Par ZP100 3K User manual

User Manual
PAR ZP100 3K

©2020 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade-
marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-
tion of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!
ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 2
Date Document
Version
Software
Version DMX Channels Notes
09/27/2017 1.0 1.0 1 / 2 / 3 Initial Release
01/02/2018 2.0 1.2 1 / 2 / 3 / 4
Added RDM protocol support, 4-ch DMX
mode, Stage 2 dimmer curve, default
settings system menu.
12/17/2020 3.0 1.6 No Change Updated DMX Setup.
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update of this manual
before beginning installation and/or programming.

ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 3
Unpacking: Thank you for purchasing the Par ZP100 3K by ADJ Products, LLC. Every Par ZP100 3K
has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping. If the carton appears to be dam-
aged, carefully inspect your xture for any damage and be sure all equipment necessary to operate the
unit has arrived intact. In the event damage has been found or parts are missing, please contact our
toll free customer support number for further instructions. Please do not return this unit to your dealer
without contacting customer support rst.
Introduction: The Par ZP100 3K is a DMX intelligent, zooming, LED par xture. The Par ZP100 3K
operates as a stand alone xture. This xture is suitable for theaters, studios, retail stores, and other
similar locations. For best results use fog or special eects smoke to enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide help and
to answer any question should you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are
Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
Warning! This may cause severe eye damage. Avoid looking directly into the light source at all times!
Par ZP100 3K General Information

ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 4
Par ZP100 3K General Instructions
To optimize the performance of this product, please read these operating instructions carefully to
familiarize yourself with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit, for
future reference.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,
please contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid touching the unit with bare hands
while in use.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-obser-
vance of this manual or any unauthorized modification to this unit.
Par ZP100 3K Features
• DMX-512 Protocol Compatible (4 DMX Channel Modes: 1, 2, 3, or 4 channels)
• 5-Pin XLR In/Out Connections
• Power In/Out Connections
• 6 Dimmer Curve Modes
• Digital Display for Address and Function Setting
• Gamma Correction Adjustment
• Dimming Frequency Adjustment
• Multiple Unit Power Linking (see Multiple Unit Power Linking section)
Par ZP100 3K Warranty Registration
The Par ZP100 3K carries a 2 year (730 days) limited warranty. Please fill out the enclosed warranty
card to validate your purchase and warranty.
You may also register your product online at: www.adj.com.
All returned service items, whether under warranty or not, must be freight pre-paid and accompany a
return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your proof
of purchase invoice. Please contact ADJ Products, LLC customer support for a R.A. number.
Par ZP100 3K Handling Precautions

ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 5
Par ZP100 3K Safety Precautions
For Your Own Personal Safety, Please Read and Understand This Manual Completely Before
You Attempt To Install Or Operate This Unit!
• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required voltage for your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken.
• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is
used to reduce the risk of electrical shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when its cover is removed.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
• Do not attempt to operate this unit if it has been damaged.
• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the appliance.
• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the
Cleaning section of this manual for details.
• Heat - This fixture should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally, or exhibits a marked change in perfor-
mance.

Par ZP100 3K DMX Set Up
ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 6
Power Supply: The ADJ Par ZP100 3K contains an automatic voltage switch, which will auto sense
the voltage when it is plugged into the power source. With this switch there is no need to worry
about the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and
controller manufacturers as a form of communication between intelligent xtures and controllers. A
DMX controller sends DMX data instructions from the controller to the xture. DMX data is sent as
serial data that travels from xture to xture via the DATA “IN” and DATA “OUT” XLR terminals locat-
ed on all DMX xtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX xtures try to use
the shortest cable path possible. The order in which xtures are connected in a DMX line does not
inuence the DMX addressing. For example; a xture assigned a DMX address of 1 may be placed
anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements: The Par ZP100 3K can be controlled via DMX-512 pro-
tocol. The Par ZP100 3K has four DMX channel modes; 1 channel mode, 2 channel mode, 3 chan-
nel mode, & 4 channel mode. The DMX address is set electronically using the controls on the rear
panel of the unit. Your unit and your DMX controller require an approved DMX-512 110 Ohm Data
cable for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and lighting stores). Your cables should be made with a
male and female XLR connector on either end of the cable. Also remember that DMX cable must be
daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 7
Par ZP100 3K DMX Set Up
Notice: Be sure to follow gures two and three when making your own cables. Do not use the
ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug
or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield
could cause a short circuit and erratic behavior.
Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-
nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which
is connected between pins 2 and 3 of a male XLR connector (DATA+ and DATA-). This unit is inserted
in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.
5-Pin XLR DMX Connectors. This unit use 5-pin DMX-512 data cables for DATA transmission. 5-pin
DMX xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in
to a 3-pin line, a cable adaptor must be used. These adaptors are readily available at most electron-
ics stores. The chart below details a proper cable conversion.

ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 8
Par ZP100 3K System Menu

ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 9
System Menu: When making adjustments press ENTER to conrm your setup then press and
hold the MENU button for at least 3 seconds. To exit without making any adjust-ments press
the MENU button. The display will lock after 30 seconds, press the MENU button for 3 sec-
onds to unlock.
Addr - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until “Addr” is displayed. Press ENTER.
2. The current address will now be displayed and ashing. Press the UP or DOWN buttons to nd
your desired address. Press ENTER to set your desired DMX address.
Chnd - This will let you select your desired DMX channel mode.
1. Press the either the MENU button until “Chnd” is displayed, press ENTER. The current DMX
channel mode will be displayed.
2. Press the UP or DOWN buttons to nd your desired DMX channel mode and press ENTER to
conm and exit.
dnSt - This setting denes the behavior of the xture in the event that the DMX signal is lost,
interrupted, or power is lost.
1. Press the MENU button until “dnSt” is displayed, and either “BLND or “LAST” will be displayed
beneath.
2. Press ENTER and the bottom choice will begin to ash. Use the UP or DOWN buttons to choose
an operating mode you would like the unit to start up in when power is applied or the DMX signal
is lost.
• BLND (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into
stand by mode.
• HOLD - If the DMX signal is lost the xture will stay in the last DMX setting. If power is ap-
plied and this mode is set, the unit will automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
dInd - This will let select your desired dimmer curve.
1. Press the MENU button until “dInd” is displayed, and press ENTER. 1 of 6 dimmer curves will be
displayed. See the Dimmer Curve Chart section of this manual for details.
• “STDA” (standard)
• “STGE” (stage)
• “TV” (TV)
• “ARAL” (Architectural)
• “THAL” (Theatre)
• (Stage 2)
2. Press the UP or DOWN buttons to nd your desired dimmer curve and press ENTER to conm
and exit.
Par ZP100 3K System Menu

ADJ Products, LLC - www.adj.com - Par ZP100 3K User Manual Page 10
Par ZP100 3K System Menu
FReq - With this function you can adjust the dimming frequency.
1. Press the MENU button until “FReq” is displayed, then press ENTER.
2. Use the UP or DOWN buttons to adjust the dimming frequency between 900hz, 1000hz, 1100hz,
1200hz, 1300hz, 1400hz, 1500hz, 2500hz, 4000hz, 5000hz, 10000hz, 15000hz, 20000hz, or
250000hz.
3. Once you have found your desired dimming frequency press ENTER to conrm.
gAnn - In this menu you are able to make gamma corrections.
1. Press the MENU button until “gAnn” is displayed, then press ENTER.
2. Use the UP or DOWN buttons to scroll through gamma correction options.
3. Once you have found your desired gamma correction press ENTER to conrm.
dISP - This function will invert the display 180 degrees.
1. Press the MENU button until “dISP” is displayed, then press ENTER.
2. Press the UP button to select “dSIP” to “ip” the display, or “dISP” to revert the display to nor-
mal.
3. Press ENTER to conrm.
NAnd - This function will allow you to manually adjust each brightness, ne dimming, and
strobing. Fine dimming and strobing are only used with 3 channel mode.
1. Press the MENU button until “NAnd” is displayed, then press ENTER.
2. Use the UP and DOWN buttons to scroll through the settings. Once you have found your desired
function you would like to adjust press ENTER.
3. After you have pressed ENTER, use the UP and DOWN buttons to adjust the values. Once you
have made your adjustments press ENTER to set them. Press the MENU button to exit.
teSt - This function will run a self-test program.
1. Press the MENU button until “teSt” is displayed, then press ENTER.
2. The xture will now run a self test. Press the MENU button to exit and quit the self test.
tENP - With this function you can check the temperature of the xture.
1. Press the MENU button until “tENP” is displayed, then press ENTER.
2. The xture temperature will now be displayed. Press MENU to exit.
FhrS - With this function you can display the running time of the unit.
1. Press the MENU button until “FhrS” is displayed, then press ENTER.
2. The running time of the xture will now be displayed. Press MENU to exit.
ver - Use this function to display the software version of the unit.
1. Press the MENU button until “ver” is displayed, then press ENTER.
2. The display will now show the software version.