ADTRAN jobAid+ 1200482G1 User manual

jobAid
DESCRIPTION
The 2.5 Gbps Multimode SFP plugs into ADTRAN GigE modules
designed to accept SFPs. The SFP provides an optical interface to
the GigE physical interface. Installed into an appropriate host
module, the SFP provides a GigE interface to the supporting
system.
NOTE
To ensure compatibility, refer to the documentation provided
with the host module.
The following features are supported on the SFP:
■Tri-Rate 1.063/2.125/4.25 Gbps, 850 nm, multi-mode, 2 fiber
operation
■Maximum Optical distance: see table below.
Maximum Optical Distance Table
CAUTION
!
Due to compliance certification requirements, only SFPs supplied
by ADTRAN are to be used with ADTRAN modules. ADTRAN
cannot certify system integrity with other SFPs.
Data Rate OM3 MMF OM2 MMF OM1 MMF
1.062 Gbps 860m 550m 300m
2.125 Gbps 500m 300m 150m
4.25 Gbps 380m 150m 70m
Small Form-factor Pluggable
2.5 GBPS MULTIMODE SFP
Specifications
■Optical Specifications:
♦Optical transmit level: –2.5 dBm to –9.0 dBm
♦Optical receive level:
●1.062 Gbps, –3.0 dBm to –15.0 dBm
●2.125 Gbps, –3.0 dBm to –13.0 dBm
●4.25 Gbps, –3.0 dBm to –12.0 dBm
♦Link power budget: 6.0 dB
♦Optical connectors: LC
INSTALLATION
Before installing the equipment, inspect the SFP. If damage has
occurred during shipping, file a claim with the carrier, and then
contact ADTRAN Customer Support. For more information, refer
to the warranty.
To install the SFP into an appropriate module, complete the
following steps:
NOTE
Do not remove the protective end cap from the SFP until you are
ready to connect the fiber optic cable.
1. Insert the SFP into the SFP cage on the module. Ensuring
that the latch handle on the SFP is facing upward, slide the
SFP all the way into the SFP cage until there is an audible
“click”.
NOTE
The latch on the SFP is for removal only. When removing the SFP,
rotate the latch away from the SFP, the SFP should easily slide out
of the cage.
2. Remove the end cap and connect the fiber to the SFP+.
NOTICE
We recommend that you keep the protective end cap on
whenever the transceiver optical fiber connector is not in use.
3. Continue the installation and turn-up of the host module
using the instructions in the Job Aid provided with the
module or other system-level documentation available
online at www.adtran.com.
Product P/N: 1200482G1
Issue Date: March 2016
Document P/N: 61200482G1-22A
Documentation for ADTRAN Access and Aggregation products is
available for viewing and download directly from the ADTRAN Support
Community website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following related online documents and resources provide additional information for this
product:
SFP/XFP/SFP+ Compatibility Matrix (online tool, go to: http://www.adtran.com/sfp)

SAFETY AND REGULATORY COMPLIANCE
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment.
CAUTION
!
■Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
■The ADTRAN system chassis frame ground terminal must be
connected to an earth ground to ensure that the metal
enclosure of the SFP is properly grounded via the backplane
connector.
NOTE
■This product is NRTL Listed to the applicable UL Standards.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received,
including interference that may cause undesired operation.
■Changes or modifications not expressly approved by
ADTRAN could void the user's authority to operate this
equipment.
■Install this product in a Restricted Access Location. This
product is intended to be installed and serviced by qualified
Service Personnel only.
■This product meets EU RoHS Directive 2011/65/EU and/or
applicable exemptions. Refer to www.adtran.com for further
information on RoHS/WEEE..
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2016 ADTRAN, Inc. All Rights Reserved.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61200482G1-22A*