Advantech WISE-3310 User manual

User Manual
WISE-3310

WISE-3310 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2015
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Linear Dust is a trademark of Linear Technology Corporation.
ARM is a trademark of ARM Corporation.
All other product names or trademarks are properties of their respective owners.
Packing List
Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.
Gateway
–WISE-3310 (P/N: WISE-3310-D200L1E)
Accessory
–2.4 GHz Antenna *2 (P/N: 1750007622-01)
–Adapter *1 (P/N: 96PSA-A36W12R1)
Part No. Edition 1
Printed in Taiwan September 2015

iii WISE-3310 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -40° C (-40° F) OR ABOVE 85°
C (185° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: THERE IS DANGER OF EXPLOSION IF BATTERY IS INCOR-
RECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BAT-
TERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

WISE-3310 User Manual iv

v WISE-3310 User Manual
Contents
Chapter 1 General Introduction ...........................1
1.1 Introduction ............................................................................................... 2
1.2 Product Features....................................................................................... 2
1.2.1 Key Features................................................................................. 2
1.2.2 Key Specification .......................................................................... 2
1.3 Mechanical Specification........................................................................... 3
1.3.1 Dimensions: .................................................................................. 3
1.4 Power Requirement .................................................................................. 3
1.5 Environment Specifications....................................................................... 3
Chapter 2 Hardware Functionality.......................5
2.1 Introduction ............................................................................................... 6
2.2 WISE-3310 I/O Indication.......................................................................... 6
Figure 2.1 WISE-3310 front view................................................. 6
Figure 2.2 WISE-3310 Back view ................................................ 6
2.3 WISE-3310 Antenna Connectors .............................................................. 6
2.3.1 Spare Antenna Hole...................................................................... 6
2.3.2 Power Input Connector ................................................................. 7
2.3.3 Power Switch ................................................................................ 7
2.3.4 COM Connector............................................................................ 7
Table 2.1: COM Connector Pin Assignment................................ 7
2.3.5 Reset Button ................................................................................. 8
2.3.6 Ethernet Connector (LAN) ............................................................ 8
Table 2.2: LAN Connector Pin Assignment ................................. 8
2.3.7 SD Connector ............................................................................... 9
Table 2.3: SD Connector Pin Assignment................................... 9
2.4 WISE-3310 Hardware Installation ............................................................. 9
2.4.1 SD Card Installation ...................................................................... 9
Figure 2.3 WISE-3310 SD Card Installation ................................ 9
2.4.2 Mounting Assembly Method........................................................ 10
Figure 2.4 Flexible wall mounting .............................................. 10
2.5 Test Tools ............................................................................................... 10
2.5.1 SD Test ....................................................................................... 10
2.5.2 Mini PCIe (Wi-Fi) Test................................................................. 11
2.5.3 LAN Test ..................................................................................... 11
2.5.4 RS232 Test ................................................................................. 12
Chapter 3 Building a WSN Network...................13
3.1 Default Setting......................................................................................... 14
3.2 Login ....................................................................................................... 14
3.3 Web Setting Functions ............................................................................ 15
3.3.1 Webmin....................................................................................... 15
3.3.2 System ........................................................................................ 15
Table 3.1: Bootup and Shutdown .............................................. 16
3.3.3 Networking .................................................................................. 18
Table 3.2: WISE WSN Setting................................................... 19
Table 3.3: WSN Network Statistic ............................................. 20
Table 3.4: WSN Network Statistic ............................................. 20
3.3.4 Hardware .................................................................................... 20

WISE-3310 User Manual vi
Chapter 4 Basic COM Port Settings..................23
4.1 Introduction ............................................................................................. 24
4.1.1 CLI Access.................................................................................. 24
4.1.2 Managing user and viewer Passwords ....................................... 25
4.1.3 Mote Commands ........................................................................ 25
4.2 Commands.............................................................................................. 25
4.2.1 Login........................................................................................... 25
4.2.2 Logout......................................................................................... 26
4.2.3 Reset .......................................................................................... 26
4.2.4 Show Config & Show Curconfig.................................................. 27
4.2.5 Show Mote.................................................................................. 28
4.2.6 Show Stat ................................................................................... 29
4.2.7 Set Netid & Set Commonjoinkey ................................................ 30
4.2.8 exec exchNetId........................................................................... 31
4.2.9 exec exchJoinKey....................................................................... 31
4.2.10 sm............................................................................................... 32

Chapter 1
1General Introduction

WISE-3310 User Manual 2
1.1 Introduction
Advantech Wireless IoT Gateway, WISE-3310, is powered by Freescale ARM® Cor-
tex™-A9 i.MX6 Dual 1 GHz high performance processor. With high-reliability wireless
mesh network solution and remote management, WISE-3310 creates a cost-effective
open platform for easy integration and development in different M2M/IoT applica-
tions. Connect with Advantech Wireless IoT nodes, by Smartmesh IP protocol for
applications in wireless sensor networks where seamless internet protocol (IP) is val-
ued. Also, WISE-3310 supportS SUSIAccess for an IoT PaaS Solution; it allows
users to easily remote control and manage their devices through WISE CLOUD.
1.2 Product Features
1.2.1 Key Features
Freescale ARM® Cortex™-A9 i.MX6 Dual 1 GHz high performance processor
Onboard DDR3 1 GB memory and 4 GB flash capability
Linear Tech Dust WSN IP Smartmesh solution
Complaint with IPv6, 6LowPAN Internet Protocol and IEEE802.15.4e standard
Supports wallmount, VESA mount for flexible mounting methods
1.2.2 Key Specification
Kernel: Linux V3.0.35
System Memory: Onboard 1GB DDR3 memory
Flash: Onboard 4 GB e.MMC flash
COM Port: 1 x RS232 Port (2 wires)
LED: 2 LED for WSN network power status
SD slot: 1 x SD Slot
Power input: 12 V DC
Power reset: 1 x reset button for system reboot

3 WISE-3310 User Manual
Chapter 1 General Introduction
1.3 Mechanical Specification
1.3.1 Dimensions:
205 x 126 x 31 mm (L x W x H) with the metal plate
180 x114 x 31 mm without metal plate
1.4 Power Requirement
System Power: DC 12 V
RTC Battery: 3 V/210 mAh
1.5 Environment Specifications
Operating Temperature: 0 ~ 40° C (32 ~ 104° F)
Relative Humidity: 95% @ 40° C (non-condensing)
Storage Temperature: -20 ~ 60° C (-4 ~ 104° F)
Vibration Loading During Operation: 1 Gms, IEC 60068-2-64, random, 5 ~
500 Hz, 1 Oct/min, 1 hr/axis.
EMC: CE, FCC Class B

WISE-3310 User Manual 4

Chapter 2
2Hardware
Functionality

WISE-3310 User Manual 6
2.1 Introduction
The following sections show the external connectors and pin assignments for appli-
cations.
2.2 WISE-3310 I/O Indication
Figure 2.1 WISE-3310 front view
Figure 2.2 WISE-3310 Back view
2.3 WISE-3310 Antenna Connectors
2.3.1 Spare Antenna Hole
The WISE-3310 provides 2 spare antenna holes for standard SMA connectors.

7 WISE-3310 User Manual
Chapter 2 Hardware Functionality
2.3.2 Power Input Connector
The WISE-3310 comes with a DC-jack header for 12V DC external power input.
2.3.3 Power Switch
The WISE-3310 has a power switch on the front side.
2.3.4 COM Connector
The WISE-3310 provides one D-sub 9-pin connector serial communication interface
port. The port can support RS-232 mode communication.
Table 2.1: COM Connector Pin Assignment
Pin Description Pin Description
1 N/C 2 UART1_RXD
3 UART1_TXD 4 N/C
5GND 6 N/C
7 N/C 8 N/C
9N/C

WISE-3310 User Manual 8
2.3.5 Reset Button
The WISE-3310 has a reset button on the front side. Press this button to activate the
hardware reset function.
2.3.6 Ethernet Connector (LAN)
The WISE-3310 provides one RJ45 LAN interface connector, it is fully compliant with
IEEE 802.3u 10/100/1000 Base-T CSMA/CD standards. The Ethernet port provides
standard RJ-45 connector with LED indicators on the front side to show Active/Link
status.
Table 2.2: LAN Connector Pin Assignment
Pin Description Pin Description
1 TX+(10/100),BI_DA+(GHz) 5 BI_DC-(GHz)
2 TX-(10/100),BI_DA-(GHz) 6 RX-(10/100),BI_DB-(GHz)
3 RX+(10/100),BI_DB+(GHz) 7 BI_DD+(GHz)
4 BI_DC+(GHz) 8 BI_DD-(GHz)

9 WISE-3310 User Manual
Chapter 2 Hardware Functionality
2.3.7 SD Connector
The WISE-3310 provides an SD slot. Users can insert an SD card easily.
2.4 WISE-3310 Hardware Installation
2.4.1 SD Card Installation
1. Switch off the Power switch.
2. Insert SD Card directly into the WISE-3310 SD slot, as Figure 2.3.
Figure 2.3 WISE-3310 SD Card Installation
Table 2.3: SD Connector Pin Assignment
Pin Description Pin Description
1 SD2_DATA3 2 SD2_CMD
3GND 4 +V3.3
5 SD2_CLK 6 GND
7 SD2_DATA0 8 SD2_DATA1
9 SD2_DATA2 10 SD2_CD#
11 GND 12 SD2_WP

WISE-3310 User Manual 10
2.4.2 Mounting Assembly Method
You can fix WISE-3310 to a wall by using wall mounting kit, as Figure 2.4.
Figure 2.4 Flexible wall mounting
2.5 Test Tools
All test tools must be verified on WISE-3310, please prepare required test fixtures
before verifying each specified I/O. If you have any problems getting test fixtures,
please contact Advantech for help.
2.5.1 SD Test
1. When booting from eMMC, you should see only the directories below:
#ls /dev/mmcblk*
/dev/mmcblk0 /dev/mmcblk0boot0 /dev/mmcblk0boot1 /dev/ mmcblk0p1
2. Insert SD card to SD card slot (SD1) and check your device again. You should
be able to see more directories. /dev/mmcblk1 is the SD card storage.
#ls /dev/mmcblk*
/dev/mmcblk0 /dev/mmcblk0boot1 /dev/mmcblk1 /dev/mmcblk1p2
/dev/mmcblk0boot0 /dev/mmcblk0p1 /dev/mmcblk1p1
3. Create a file and copy to SD.
#echo 123456789ABCDEF > test.txt
#dd if=./test.txt of=/dev/mmcblk1 bs=1024 count=1
seek=25118
0+1 records in
0+1 records out
16 bytes (16 B) copied, 0.000109331 s, 146 kB/s

11 WISE-3310 User Manual
Chapter 2 Hardware Functionality
4. Check if the file was created successfully.
#hexdump -C /dev/mmcblk1 -s 25720832 -s 32
01887800 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 0a
|123456789ABCDEF.|
01887810 1d 4f e2 19 d3 05 8b df ab 4a 40 5a c5 23 3c f2
|................|
2.5.2 Mini PCIe (Wi-Fi) Test
The command used to test Wi-Fi module is as follows, the supported module P/N is
EWM-W142H01E.
#ifconfig wlan0 up
#iwlist wlan0 scanning
#wpa_passphrase “Wifi name” password > /tmp/wpa.conf
#wpa_supplicant –Bdwext –iwlan0 –c/tmp/wpa.conf
#dhclient wlan0
2.5.3 LAN Test
WISE-3310 sets DHCP as default network protocol.
#ifconfig
eth0 Link encap:Ethernet HWaddr 00:04:9F:01:30:E0
inet addr:172.17.21.96 Bcast:172.17.21.255
Mask:255.255.254.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:129 errors:0 dropped:18 overruns:0
frame:0
TX packets:2 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:1000
RX bytes:15016 (14.6 KiB) TX bytes:656 (656.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:0 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Note! Please make sure that parameter “seek” is equal to 25118 as indicated
in the above codes. If you create the file to a wrong sector, that may
damage the system.

WISE-3310 User Manual 12
If you would like to config IP manually, please use the command below:
#ifconfig eth0 xxx.xxx.xxx.xxx up
Here is a real case for your reference.The host’s (WISE-3310) IP is 172.17.21.97; the
target (a desktop computer) IP is 172.17.20.192.
#ifconfig eth0 172.17.21.97 up
#ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:04:9F:01:30:E0
inet addr:172.17.21.97 Bcast:172.17.255.255
Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:2851 errors:0 dropped:271 overruns:0
frame:0
TX packets:30 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:1000
RX bytes:291407 (284.5 KiB) TX bytes:2000 (1.9
KiB)
The target computer (Client) IP address is 172.17.20.192, so we can use the below
command to see if we can get any response from the client.
#ping 172.17.20.192
PING 172.17.20.192 (172.17.20.192): 56 data bytes
64 bytes from 172.17.20.192: seq=0 ttl=128 time=7.417 ms
64 bytes from 172.17.20.192: seq=1 ttl=128 time=0.203 ms
64 bytes from 172.17.20.192: seq=2 ttl=128 time=0.300 ms
--- 172.17.20.192 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.203/2.640/7.417 ms
2.5.4 RS232 Test
RS232 port is debug console for WISE-3310.

Chapter 3
3Building a WSN
Network

WISE-3310 User Manual 14
This chapter will show you how to configure WISE-3310 by using the web-based con-
figuration interface.
3.1 Default Setting
Please use your Ethernet port to connect to WISE-3310.
3.2 Login
1. Open a web browser (Chrome is suggested) and enter the IP Address.
http://192.168.0.1
2. The default username and password are both admin. Once you have entered
the correct username and password, click the Login button to open the web-
base configuration page.
IP Address 192.168.0.1
User Name/ Password admin/admin
Network ID WSN1/ WSN2 2001/2002
Join Key JOINADVANTECHIOT
Note! If you have changed the default LAN IP Address of this device, ensure
you enter the correct IP Address.