Advantech UNO-410 User manual

User Manual
UNO-410 電腦
Explosion-Proof DIN-Rail
Gateway

UNO-410 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2021
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-
poration.
Intel®, Core™ and Atom™ are the trademarks of Intel® Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Support
For more information on this and other Advantech products, please visit our website
at http://www.advantech.com.
*Address of Advantech: No.1, Alley 20, Lane 26, Rueiguang Road, Neihu District,
Taipei 114519, Taiwan
For technical support services, please visit our support website at http://sup-
port.advantech.com/.
This manual applies to the following models. These are abbreviated as UNO-410
products in this article.
*Model:
Part number:
UNO-410-E1H
UNO-410-E1HX
UNO410E1Hxxxx-T
UNO410E1HXxxxx-T
UNO410E1HLxxxx-T
UNO410E1HXLxxxx-T
-E1: CPU series= Intel® ATOM™ E39xx
-H: Used in Hazardous locations
-X: Model with ATEX/IECEx certification
-L: Configurations with LTE module
-x: Numeric serial numbers
Part No. 2003041000 Edition 1
Printed in Taiwan July 2021

iii UNO-410 User Manual
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.

UNO-410 User Manual iv
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
type of cable is available from Advantech. Please contact your local supplier for
ordering information.
Test conditions for passing also include the equipment being operated within an
industrial enclosure. In order to protect the product from damage caused by electro-
static discharge (ESD) and EMI leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference. In
this event, users are required to correct the interference at their own expense.
警告使用者
這是甲類測試產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，
使用者會被要求採取某些適當的對策。
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

v UNO-410 User Manual
Safety Precautions - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from the PC chassis
before manual handling. Do not touch any components on the CPU card or
other cards while the PC is powered on.
Disconnect the power before making any configuration changes. A sudden rush
of power after connecting a jumper or installing a card may damage sensitive
electronic components.
ATEX Information
1. IECEx/ATEX Information:
–ATEX Certificate Number: UL 21 ATEX 2496X
–IECEx Certificate Number: IECEx UL 21.0060X
2. Ambient Temperature Range (°C):
Temperature code: T4
-40°C ≤ Tamb ≤ +55°C for model suffix without “L”
-40°C ≤ Tamb ≤ +40°C for model suffix with “L”
3. Certification String:
4. Standards Covered:
–IEC 60079-0, Edition 7
–IEC 60079-7, Edition 5.1
–EN IEC 60079-0:2018
–EN IEC 60079-7: 2015 +A1:2018
5. Electrical Rating:
–Power input: 10-36Vdc, 7.7-1.31A
–Digital input: 0 to 30 Vdc
–Digital output: 30Vdc, 5 mA max (UL testing condition)
6. Instructions for safe use:
–The field wiring cable should be rated ≥ 90°C.
–Input terminal block (CN1) should be installed with 12-16AWG wires and
secured with 7 lb-in torque valve.
–I/O terminal block (CN7) and COM terminal block (CN8) should be installed
with 18-22AWG wire.
7. Special conditions of safe use:
–The equipment shall only be used in an area of at least pollution degree 2, as
defined in IEC 60664-1.
–The equipment shall be mounted in vertical position and installed in an enclo-
sure that provides a minimum ingress protection of IP54 in accordance with
IEC 60079-0 and only accessible by the use of a tool.
–Transient protection shall be provided that is set at a level not exceeding
140% of the peak rated voltage value at the supply terminal to the equip-
ment.

UNO-410 User Manual vi
Safety Instructions
1. Read these safety instructions carefully.
2. Retain this user manual for future reference.
3. Disconnect the equipment from all power outlets before cleaning. Use only a
damp cloth for cleaning. Do not use liquid or spray detergents.
4. For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
5. Protect the equipment from humidity.
6. Place the equipment on a reliable surface during installation. Dropping or letting
the equipment fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
8. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet.
9. Position the power cord away from high-traffic areas. Do not place anything over
the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage from transient overvoltage.
12. Never pour liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If any of the following occurs, have the equipment checked by service person-
nel:
–The power cord or plug is damaged.
–Liquid has penetrated the equipment.
–The equipment has been exposed to moisture.
–The equipment is malfunctioning, or does not operate according to the user
manual.
–The equipment has been dropped and damaged.
–The equipment shows obvious signs of breakage.
15. Do not leave the equipment in an environment with a storage temperature of
below -40 °C (-4 °F) or above 55 °C (131 °F) as this may damage the compo-
nents. The equipment should be kept in a controlled environment.
16. CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only
with the same or equivalent type as recommended by the manufacturer. Discard
used batteries according to the manufacturer’s instructions.
17. In accordance with IEC 704-1:1982 specifications, the sound pressure level at
the operator’s position does not exceed 70 dB (A).
18. This product is intended to be supplied by an UL certified power supply or dc
source with SELV output, rated 10 Vdc, 7.7A minimum and Tma 55 degree. If
you need further assistance, please contact Advantech for further information.
19. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet. The power outlet socket should have a grounded
connection.
20. For use in pollution free environments and indoor use.
21. This equipment is not suitable for use in locations where children are likely to be
present.
22. If the equipment is used in a manner not specified by the Advantech, the protec-
tion provided by the equipment may be impaired.

vii UNO-410 User Manual
23. The equipment contains no user-serviceable parts. Do not open, Return to man-
ufacturer for servicing.
24. Do not block air ventilation holes.
25. This is open type equipment and should be installed in a suitable enclosure.
26. UNO-410 is intended to be DIN rail mounted and must be installed in a tool
accessible enclosure.” or equivalent.
27. UNO-410 is suitable for use in Class I, Division 2, Groups A, B, C and D or non-
hazardous locations only.
Temperature code: T4
28. WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT
WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS KNOWN TO BE
FREE OF IGNITABLE CONENTRATIONS.
29. WARNING: EXPLOSION HAZARD - For UNO-410, do not substitute any com-
ponents which may impair suitability for Class I, Division 2.
30. For use in Pollution Degree 2 Environment.
CAUTION: FOR USE IN A CONTROLLED ENVIRONMENT.
DISCLAIMER: These instructions are provided according to IEC 704-1 standards.
Advantech disclaims all responsibility for the accuracy of any statements contained
herein.
Consignes de sécurité
1. Lire attentivement les instructions de sécurité.
2. Conserver ce manuel pour utilisation ultérieure,
3. Débranchez cet équipement de toute prise secteur avant le nettoyer. Utilisez
seulement un chiffon humide. N'utilisez pas de détergent liquide ou pulvérisé
pour le nettoyage.
4. Gardez cet équipement à l'abri de l'humidité.
5. Placez cet équipement sur une surface fiable pendant l'installation. Le faire ou
bien le laisser tomber peut causer des dégâts.
6. Les ouvertures sur l'enceinte servent à la convection de l'air. Protégez l'équipe-
ment contre surchauffe. NE COUVREZ PAS LES OUVERTURES.
7. Assurez-vous que la tension de la source d'alimentation est correcte avant de
connecter l'équipement à une prise de courant. La prise de courant doit avoir
une connexion à la terre.
8. Placez le câble d'alimentation de manière à ce que personne ne puisse marcher
dessus. Ne placez rien sur le câble d'alimentation.
9. Toutes les mises en garde et tous les avertissements sur l'équipement doivent
être notés.
10. Si l'équipement n'est pas utilisé pendant une longue période, débranchez-le de
la source d'alimentation pour éviter tout endommagement dû à une surtension
transitoire.
11. Ne jamais verser de liquide dans une ouverture. Cela pourrait provoquer un
incendie ou un choc électrique.
12. N'ouvrez jamais l'équipement. Pour des raisons de sécurité, l'équipement doit
être ouvert uniquement par du personnel qualifié.
13. Si l'une des situations suivantes se présente, faites vérifier l'équipement par le
personnel de service:
un liquide a pénétré dans l'équipment.
L'équipement a été exposé à l'humidité.
L'équipement ne fonctionne pas bien, ou vous ne pouvez pas le faire
fonctionner selon le manuel de l'utilisateur.

UNO-410 User Manual viii
The equipment does not work well, or you cannot get it to work according to
the user's manual.
L'équipement est tombé et endommagé.
L'équipement présente des signes évidents de rupture.
14. NE LAISSEZ PAS CET ÉQUIPEMENT DANS UN ENVIRONNEMENT OU LA
TEMPÉRATURE DE STOCKAGE PEUT ÊTRE INFÉRIEURE À -40 ° C (-4 ° F)
OU BIEN SUPÉRIEURE À 55 ° C (131 ° F). CECI POURRAIT ENDOMMAGER
L'EQUIPEMENT. L'ÉQUIPEMENT DEVRAIT ÊTRE DANS UN ENVIRONNE-
MENT CONTRÔLÉ.
15. Ce produit est destiné à être alimenté par une source d'alimentation certifiée UL
ou par une source cc convenant à une utilisation à une température minimale
de 40 degrés Celsius, dont la sortie est conforme à la norme SELV et dont la
puissance nominale est de 10 Vdc, 7.7 A, en cas de besoin. contactez Advant-
ech pour plus d'informations.
16. Pour une utilisation dans des environnements non polluant et à l'intérieur.
17. C'est appareil ne doit pas être utilisé dans des endroits où se trouvent des
enfants.
18. Si l'équipement est utilisé d'une manière non spécifiée par le fabricant, la pro-
tection fournie par l'équipement peut être altéré.
19. L'équipement ne contient aucune pièce réparable par l'utilisateur. Ne pas ouvrir,
retourner au fabricant pour réparation.
20. Ne bloquez pas les ou es de ventilation.
21. Il s'agit d'un équipement de type ouvert et doit être installé dans un boîtier
approprié.
22. AVERTISSEMENT: Ce équipement est adapté á une utilisation en Classe I,
23. Division 2, Groupes A, B, C, et D ou non dangereux.
Code de température: T4.
24. AVERTISSEMENT: RISQUE D'EXPLOSION - Ne pas brancher ou débrancher
l'équipement que l'alimentation a été retiré ou la région est connue pour ětre
non dangereux.
25. AVERTISSEMENT: RISQUE D'EXPLOSION - Remplacement de tous les com-
posants peut nuire la conformité de Classe I, Division 2.
26. ATTENTION: Pour utilisation dans un environnement contrôlé.
ATTENTION: Danger d'explosion si la batterie est mal remplace. Remplacer unique-
ment par le meme type ou equivalent recommandé par le fabricant. Jeter les piles
usagées selon les instructions du fabricant.
安全指示
1. 請仔細閱讀此安全操作說明。
2. 請妥善保存此用戶手冊供日後參考。
3. 用濕抹布清洗設備前，請確認拔除電源線。請勿使用液體或去污噴霧劑清洗設
備。
4. 對於使用電源線的設備，設備周圍必須有容易接觸到的電源插座。
5. 請勿在潮濕環境中試用設備。
6. 請在安裝前確保設備放置在可靠的平面上，意外摔落可能會導致設備損壞。
7. 設備機殼的開孔適用於空氣對，從而防止設備過熱。請勿覆蓋開孔。
8. 當您連接設備到電源插座前，請確認電源插座的電壓符合要求。
9. 請將電源線佈置在人們不易絆倒的位置，請勿在電源線上覆蓋任何雜物。
10. 請注意設備上所有的警告標示。

ix UNO-410 User Manual
11. 如果長時間不使用設備，請拔除與電源插座的連結，避免設備被超標的電壓波動
損壞。
12. 請勿讓任何液體流入通風口，以免引起火灾或短路。
13. 請勿自行打開設備。為了確保您的安全，請透過經認證的工程師來打開設備。
14. 如遇下列情况，請由專業人員維修：
電源線或插頭損壞。
設備內部有液體流入。
設備曾暴露在過度潮濕環境中使用。
設備無法正常工作，或您無法透過用戶手冊來正常工作。
設備摔落或損壞。
設備有明顯外觀損。
15. 請勿將設備放置在超出建議溫度範圍的環境，即不要低於 -40 °C（-40 °F）
或高於 55 °C（131 °F），否則可能會造成設備損壞。
16. 注意：若電池更換不正確，將有爆炸危險。因此，只可以使用製造商推薦的同一
種或者同等型號的電池進行替換。請按照製造商的指示處理舊電池。
17. 根據 IEC 704‐1: 1982 規定，操作員所在位置音量不可高於 70 分貝。
18. 限制區域：請勿將設備安裝於限制區域使用。
19. 免責聲明：請安全訓示符合 IEC 704‐1 要求。研華公司對其內容之準確性不承
擔任何法律責任。
20. 消费者若使用电源适配器供电，则应购买配套使用获得 CCC 认证并满足标准要
求的电源适配器。

UNO-410 User Manual x

xi UNO-410 User Manual
Contents
Chapter 1 Overview...............................................1
1.1 Introduction ............................................................................................... 2
1.2 Safety Precautions.................................................................................... 2
1.3 Packing List............................................................................................... 3
1.4 Hardware Specifications ........................................................................... 3
1.4.1 General ......................................................................................... 3
1.4.2 System Hardware ......................................................................... 4
1.4.3 I/O Interfaces ................................................................................ 4
1.4.4 Environment.................................................................................. 5
1.4.5 Certifications ................................................................................. 5
1.5 Dimensions ............................................................................................... 5
Figure 1.1 UNO-410 Dimensions................................................. 5
Chapter 2 Hardware Functionality.......................7
2.1 Introduction ............................................................................................... 8
Figure 2.1 Diagram of Connector Locations on UNO-410 (Top
Side) ........................................................................... 8
Figure 2.2 Diagram of Key Component Locations on UNO-410
(Bottom Side).............................................................. 8
Table 2.1: Key components, Connectors on Board..................... 9
2.2 External I/O Connector............................................................................ 10
Figure 2.3 Front Panel of UNO-410........................................... 10
Figure 2.4 Top View of UNO-410 .............................................. 10
2.2.1 Power Connector ........................................................................ 10
2.2.2 LAN: Ethernet Connector............................................................ 10
2.2.3 USB Connector........................................................................... 11
2.2.4 Display Connector....................................................................... 11
2.2.5 COM Connector (CN8) ............................................................... 11
Table 2.2: COM Connector Pin Assignments............................ 11
2.2.6 Digital Input and Output (CN7).................................................... 12
Figure 2.5 Isolated DI Wet Connection Diagram ....................... 13
Figure 2.6 Isolated DI Dry Connection Diagram........................ 13
Figure 2.7 Isolated DO Connection Diagram............................. 13
2.3 Internal I/O Connectors and Switches..................................................... 14
Figure 2.8 Locations Internal I/O Connectors/Switches for UNO-
410............................................................................ 14
Table 2.3: Internal Connectors and Jumper Switches............... 14
2.3.1 SATA Connector/SATA Power Connector.................................. 15
2.3.2 M.2 Connector ............................................................................ 15
2.3.3 mPCIe Connector ....................................................................... 15
2.3.4 Nano SIM Slot............................................................................. 15
2.4 Others ..................................................................................................... 16
Figure 2.9 LED Indicators, Reset Buttons, and Antenna Hole... 16
2.4.1 LED Indicators ............................................................................ 16
2.4.2 Reset Buttons ............................................................................. 16
2.4.3 Antenna Hole .............................................................................. 17
Figure 2.10Diagram of Maximum OD Value for Antenna Hole... 17
Chapter 3 Initial Setup ........................................19
3.1 Chassis Grounding.................................................................................. 20
Figure 3.1 Chassis Grounding Connection Diagram ................. 20

UNO-410 User Manual xii
3.2 Connecting Power................................................................................... 21
3.3 Storage Installation (optional) ................................................................. 22
3.3.1 Installing a 2.5” HDD/SSD (2.5"SSD is default in UNO-410-E1HX)
22
3.3.2 Installing M.2 SSD ...................................................................... 27
3.4 Din-Rail Installation ................................................................................. 28
3.5 Wireless Module Installation (Optional) .................................................. 30
3.6 iDoor Installation ..................................................................................... 34
3.7 Installing lockable kit ............................................................................... 35
3.7.1 Purpose ...................................................................................... 35
3.7.2 Part number................................................................................ 35
3.7.3 Lockable kit configuration ........................................................... 35
3.7.4 Assembly with the UNO System................................................. 36
3.8 Remote Power & Reset Settings ............................................................ 37
Table 3.1: Remote Power/On & Reset Settings........................ 37
3.9 BIOS Setting ........................................................................................... 37
Appendix A System Settings/Pin Assignments.. 39
A.1 Power Connector (CN1).......................................................................... 40
Table A.1: Power Connector Pin Assignments.......................... 40
A.2 LAN: Ethernet Connector (CN4) ............................................................. 40
Table A.2: Ethernet Connector Pin Assignments ...................... 40
A.3 USB Connector (CN5,CN6) .................................................................... 41
A.3.1 USB 2.0 Connector..................................................................... 41
Table A.3: Connector Pin Assignments..................................... 41
A.3.2 USB 3.0 Connector..................................................................... 41
Table A.4: USB 3.0 Connector Pin Assignments....................... 41
A.4 Display Connector (CN2,CN3)................................................................ 42
Table A.5: Display Port Adapter cable Pin Assignments........... 42
A.5 SATA Connector/SATA Power Connector.............................................. 43
A.5.1 SATA Connector (SATA1).......................................................... 43
Table A.6: SATA Connector Pin Assignments........................... 43
A.5.2 SATA Power Connector (CN9)................................................... 43
Table A.7: SATA Power Connector Pin Assignments ............... 43
A.6 M.2 Connector (CN15)............................................................................ 44
Table A.8: M.2 B Key Connector Pin Assignments ................... 44
A.7 mPCIe Connector (MINI1) ...................................................................... 45
Table A.9: mPCIe Connector Pin Assignments......................... 45
A.8 COM Port RS232/422/485 Settings........................................................ 46
A.8.1 RS232/422/485 Setting (SW1) ................................................... 46
A.8.2 COM Port RS422/485 Termination Resistor Setting .................. 47
A.9 AT/ATX Setting (SW8) ............................................................................ 47
A.10 Board to Board Connector (Reserved for Expansion) (CN13)................ 48
Table A.10:Expansion Board to Board Connector Pin Assignments
48
A.11 TPM 2.0 BIOS Setting............................................................................. 49
A.12 CPU Turbo Mode BIOS Setting .............................................................. 51

Chapter 1
1Overview
This chapter overviews specifica-
tions for UNO-410.
Introduction
Safety Precautions
Accessories
Hardware Specifications
Dimensions

UNO-410 User Manual 2
1.1 Introduction
In hazardous locations, devices are under potential danger from flammable gases,
combustible dust, or ignitable fibers, creating the potential for fire and explosions.
The UNO-410 is designed to be safely operated in these locations and are UL listed
for hazardous locations with Class I, Division 2, groups A, B, C, D, T4, and ATEX/
IECEx zone 2 certification. The UNO-410 is an Intel Atom DIN-rail PC with the provi-
sion of 1 x standard M.2 3052/3042 sockets and 1 x mPCIe slot that offers expand-
able wireless connectivity.
1.2 Safety Precautions
Below are a few safety precautions for preventing injury when making connections. In
most cases, users can use a standard cable for connection.
Warning! Always disconnect the power cord from the chassis before manual han-
dling. Do not connect the chassis while the system power is on. A sud-
den rush of power can damage sensitive electronic components. Only
experienced electronics personnel should open the chassis.
Warning! Toujours à la terre pour éliminer toute charge d'électricité statique avant
toucher UNO-410. Appareils électroniques modernes sont très sensi-
bles à charges d'électricité statique. Utilisez un bracelet antistatique à
tout moment. Placez tous composants électroniques sur une surface
antistatique ou dans un statique-sac blindé.
Caution! Always ground yourself to remove any static electric charge before
touching UNO-410. Modern electronic devices are very sensitive to
static electric charges. Use a grounding wrist strap at all times. Place all
electronic components on a static-dissipative surface or in a static
shielded bag.
Caution! Toujours débrancher le cordon d'alimentation de votre boîtier lorsque
vous êtes travailler. Ne branchez pas lorsque l'appareil est allumé. Un
afflux soudain de puissance peut endommager les composants électro-
niques sensibles. Seulement connu personnel de l'électronique
devraient ouvrir le châssis.

3 UNO-410 User Manual
Chapter 1 Overview
1.3 Packing List
Please refer to below packing list:
UNO-410 (with din-rail mount)
1 x 2x5 Plug-in block for COM port
1 x 2x1 Plug-in block for power wiring
1 x 2x10 Plug-in block for digital I/O wiring
4 x M3x5L screws for HDD installation
1 x M2x4L screw for mPCIe card installation
2 x Lockable kit
1 x Earth-Ground cable
1 x SATA cable (It will be installed with 2.5" SSD inside UNO-410 unit in UNO-
410-E1HX sku)
Quick Start Guide
Simplified Chinese manual
China RoHs sheet
Warranty card
If anything is missing or damaged, contact your distributor or sales representative
immediately.
1.4 Hardware Specifications
1.4.1 General
Dimensions (W x D x H) 70 x 105 x 150 mm (2.8 x 4.1 x 5.9 in)
Weight (Net) 1 kg (2.2 lb)
Mounting DIN-rail
Power Requirement 10 - 36Vdc
Power Consumption 21W (typical), 47W (Max)
Power Rating 7.7-1.31A

UNO-410 User Manual 4
1.4.2 System Hardware
1.4.3 I/O Interfaces
BIOS AMI UEFI 128Mbit
Watchdog Timer Programmable 255 levels timer interval, from 1 to 255 sec
Hardware Security TPM 2.0
Processor Intel Atom® E3940 1.6GHz (up to 1.8GHz)
Memory Built-in 8GB DDR3L 1600MHz (Up to 8GB)
Graphics Engine Intel® HD Graphics 500
Ethernet Intel® i210-IT GbE, IIEEE802.1AS, 802.3az
LED Indicators 1x Programmable,1x Power, 1x RTC Battery and LAN (Active,
Status)
Storage
1 x M.2 2242 B-key socket (SATA/USB Signal)
1 x 2.5”SSD SATA connector (1 x 2.5" 64G SATA SSD is default
in UNO-410-E1HX)
Expansion
1 x Full size mPCIe slot (PCIe/USB Signal)
1 x M.2 B-key 3042 or 3052 Module (SATA/USB Signal)
1 x Nano SIM card slot
Note! The M.2 B key can support either 2242 (w/SATA signal) or 3042/3052
Module (w/ USB signal).
Serial Ports 2 x RS-232/422/485 (terminal block), 50 ~115.2 kbps (Isolation
Protection: 2500 Vdc)
LAN Ports 2 x 10/100/1000 Mbps IEEE 802.3u 1000BASE-T Fast Ethernet
(RJ-45)
USB Ports 3 x USB 3.2 Gen1, and 1 x USB 2.0 (Type A)
Isolated DIO 8-ch digital input, 8-ch digital output (Isolation Protection:
2500Vdc)
Displays 2 x DP 1.2, up to 4096x2306@60Hz (Support DP++)
Power Connector 1 x 2 Pin (terminal block)

5 UNO-410 User Manual
Chapter 1 Overview
1.4.4 Environment
1.4.5 Certifications
1.5 Dimensions
70 x 105 x 150 mm (2.8 x 4.1 x 5.9 in)
Figure 1.1 UNO-410 Dimensions
Operating Temperature*
Conditions without airflow (Testing conditions of UL C1D2/ATEX
certification):
-40 ~ 55 °C/-40 ~ 131 °F with wide-temperature SSD or WiFi
module.
-40 ~ 40 °C/-40 ~ 104 °F with LTE module.
Note: If the environmental conditions are 0.7m/s airflow:
-40 ~ 70 °C/-40 ~ 158 °F with wide-temperature (-40 ~ 85 °C/-40
~ 185 °) 2.5"SSD, WiFi, LTE modules.
-40 ~ 60 °C/-40 ~ 140 °F with wide-temperature M.2 SSD.
Storage Temperature - 40 ~ 85 °C (-40 ~ 185 °F)
Relative Humidity 95% RH @ 40 °C/104 °F, non-condensing
Shock Protection Operating, IEC 60068-2-27, 50G, half sine, 11ms
Vibration Protection Operating, IEC 60068-2-64, 4Grms, random, 5 ~500Hz, 1hr/axis
(SSD)
Certification
CE; FCC; CCC; UL 61010-2-201
Class I, Division 2, Groups A, B, C, D
ATEX/IECEx Zone 2

UNO-410 User Manual 6

Chapter 2
2Hardware
Functionality
This chapter details setup instruc-
tions for UNO-410’s hardware
functions. It includes connecting
peripherals and indicators.
Introduction
External I/O Connector
Internal I/O Connector
LED Indicators
Reset Buttons
Antenna Hole

UNO-410 User Manual 8
2.1 Introduction
The following diagram shows the location of UNO-410’s motherboard’s key compo-
nents and internal/external connectors.
Figure 2.1 Diagram of Connector Locations on UNO-410 (Top Side)
Figure 2.2 Diagram of Key Component Locations on UNO-410 (Bottom Side)