ix AIMB-585 User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Features .................................................................................................... 2
1.3 Specifications ............................................................................................ 2
1.3.1 System .......................................................................................... 2
1.3.2 Memory ......................................................................................... 2
1.3.3 Input/Output .................................................................................. 3
1.3.4 Graphics........................................................................................ 3
1.3.5 Ethernet LAN ................................................................................ 3
1.3.6 Industrial features ......................................................................... 3
1.3.7 Mechanical and environmental specifications............................... 3
1.4 Jumpers and Connectors .......................................................................... 4
Table 1.1: Jumpers...................................................................... 4
Table 1.2: Connectors ................................................................. 4
1.5 Board layout: Jumper and Connector Locations ....................................... 5
Figure 1.1 Jumper and Connector Location ................................ 5
Figure 1.2 I/O Connectors ........................................................... 6
1.6 AIMB-585 Board Diagram ......................................................................... 6
Figure 1.3 AIMB-585 Block Diagram ........................................... 6
1.7 Safety Precautions .................................................................................... 7
1.8 Jumper Settings ........................................................................................ 7
1.8.1 How to Set Jumpers...................................................................... 7
1.8.2 CMOS Clear (CMOS1) ................................................................. 8
Table 1.3: CMOS1....................................................................... 8
1.8.3 JEDP1: eDP Power 3.3 V/ 5 V/ 12 V Selector .............................. 8
Table 1.4: JeDP1: eDP Power 3.3 V/5 V/ 12 V Selector ............. 8
1.8.4 JUSBPWR1-2 (USB Power Selection Connector)........................ 9
Table 1.5: JUSBPWR1-2 (USB Power Selection Connector) ..... 9
1.8.5 PSON1: ATX, AT Mode Selector .................................................. 9
Table 1.6: PSON1: ATX, AT Mode Selector................................ 9
1.8.6 JIR1+JOB1+JWD1: Watchdog Timer Output, OBS Alarm Option,
and CIR interface .......................................................................... 9
Table 1.7: JIR1+JOB1+JWD1: Watchdog Timer Output and OBS
Alarm Connector......................................................... 9
1.8.7 JSETCOM2: COM2 RS232, RS422, RS485 Selection............... 10
Table 1.8: COM2 RS232, RS422, RS485 Selection ................. 10
1.8.8 JCASE1: Case Open Sensor...................................................... 10
1.8.9 JCASEOP_SW1: Case Open Selection Pin Header .................. 11
Table 1.9: JCASEOP_SW1: Case Open Selection Pin Header 11
1.8.10 JSETCOM1_V1: COM1_RI# Pin RI# / 5V / 12V......................... 11
1.9 System Memory ...................................................................................... 11
1.10 Memory Installation Procedures.............................................................. 11
1.11 Cache Memory........................................................................................ 12
1.12 Processor Installation.............................................................................. 12
Chapter 2 Connecting Peripherals ....................13
2.1 Introduction ............................................................................................. 14
2.2 USB Ports (LAN1_USB12/LAN2_USB34/USB561112/USB78/USB910/
USB1516)................................................................................................ 14
Table 2.1: LAN LED Indicator.................................................... 14
2.3 USB Power Switch (JUSBPWR1/JUSBPWR2) ...................................... 15
2.4 COM1/DVI-D Connector (COM1+DVI 1) Connector ............................... 16
2.5 Serial Ports (COM1~COM6) ................................................................... 17
