Advantech AIMB-U233 User manual

User Manual
AIMB-U233
Intel 8th Gen U Series CORE i3/
i5/i7 CPU, eDP (LVDS), 2 HDMI, 2
LAN, 2 USB3.2 Gen2 x1, 4 COM
(RS-232/422/485), M.2 E-Key, M.2
B-Key, M.2 M-Key NVMe

AIMB-U233 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2020
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to improve the products described in this manual at any time without notice. No part
of this manual may be reproduced, copied, translated or transmitted in any form or by
any means without prior written permission from Advantech Co., Ltd. The information
provided in this manual is intended to be accurate and reliable. However, Advantech
Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights
of third parties, which may result from its use.
Acknowledgments
IBM and PC are trademarks of International Business Machines Corporation.
Intel® 8th Gen Core™ i3-8145UE / i5-8365UE / i7-8665UE.
Nuvoton is a trademark of Nuvoton Corporation.
All other product names or trademarks are the property of their respective owners.
Message to the Customer
Advantech Customer Services
Every Advantech product is built with the most exact specifications to ensure reliable
performance in the harsh and demanding conditions typical of industrial environ-
ments. Whether your new Advantech equipment is destined for a laboratory or fac-
tory floor, be assured that your product can provide the reliability and ease of
operation for which the name Advantech is renowned.
Your satisfaction is our primary concern. A guide to Advantech’s customer services is
provided below. To ensure that you receive the full benefit of our services, please fol-
low the instructions below.
Technical Support
We want you to get the maximum performance from your products. Should you
encounter any technical difficulties, we are available to provide assistance. Answers
to the most frequently asked questions are provided in the product documentation.
These answers are typically a lot more detailed than the ones provided over the
phone.
So please consult this manual first. If you still cannot find the answer, gather all rele-
vant information or questions that apply to your problem, and with the product close
to hand, call your dealer. Our dealers are well trained and ready to provide the sup-
port required for you to experience the most from your Advantech products. Most of
the problems reported are minor and can be easily solved over the phone.
In addition, free technical support from Advantech engineers is available every busi-
ness day. We are always willing to give advice on application requirements or specific
information regarding the installation and operation of any of our products.
Part No. 2006U23300 Edition 1
Printed in China September 2020

iii AIMB-U233 User Manual
Declaration of Conformity
FCC Class B
This device complies with the requirements in Part 15 of the FCC regulations.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to Part 15 of the FCC Regulations. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this device in a residential area is likely to cause harmful interference, in which
case users are required to correct the interference at their own expense. The user is
advised that any equipment changes or modifications not expressly approved by the
party responsible for compliance would void compliance with the FCC regulations
and, therefore, the user’s authorization to operate the equipment.
Memory Compatibility
Caution! There is a risk of a new battery exploding if incorrectly installed. Do not
attempt to recharge, force open, or heat the battery. Replace the battery
only with the same or equivalent type recommended by the manufac-
turer. Discard used batteries according to the manufacturer's instruc-
tions.
Category Speed Capacity Vendor ADVANTECH P/N ECC Result Remark
DDR4 2666 16GB Advantech AQD-SD4U16N26-
SE N PASS
Intel® 8th
Gen
Core™
Maximum
DDR4-
2400
DDR4 2666 8GB Advantech SQR-
SD4N8G2K6SNBCB N PASS
DDR4 2666 4GB Advantech SQR-
SD4N4G2K6SNEFB N PASS
DDR4 2400 4GB Advantech SQR-
SD4N4G2K4SNEEB N PASS
DDR4 2133 16GB Advantech AQD-SD4U16N21-
SE N PASS
DDR4 2133 8GB Advantech AQD-SD4U8GN21-
SG N PASS
DDR4 2400 16GB Advantech AQD-SD4U16N24-
HE N PASS
DDR4 3200 16GB Advantech 96SD4-16G3200NN-
MI N PASS

AIMB-U233 User Manual iv
Product Warranty (2 years)
Advantech warrants the original purchaser that its products will be free from defects
in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced at no charge during the warranty period. For out-of-war-
ranty repairs, users will be billed according to the cost of replacement materials, ser-
vice time, and freight. Please consult your dealer for more details.
If you believe your product is defective, please follow the steps listed below:
1. Collect all information about the problem encountered (for example, CPU
speed, Advantech products used, other hardware and software used, etc.). Note
anything abnormal and list any onscreen messages encountered when the
problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any relevant information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and proof of the purchase date (such as a photocopy of your sales
receipt) in a shippable container. Products returned without a proof of purchase
date are not eligible for our warranty service.
5. Write the RMA number clearly on the outside of the package and ship the prod-
uct prepaid to your dealer.

v AIMB-U233 User Manual
Initial Inspection
Before installing the motherboard, please ensure that the following items are
included in your shipment:
1x AIMB-U233Intel® 8th Gen Core™ i3-8145UE / i5-8365UE / i7-8665UE UTX
Motherboard
1 x GPIO cable
2 x Serial Port Cable
3 x M.2 Screw
1 x Warranty Card
1 x On-Board CPU Cooler
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. All AIMB-U233 devices are mechanically and electrically
inspected before shipment. Thus, your product should be free of marks and
scratches and in perfect working order upon receipt. While unpacking AIMB-U233,
check the product for signs of shipping damage (for example, a damaged box,
scratches, dents, etc.). If the device is damaged or fails to meet the specifications,
notify our service department or your local sales representative immediately. Please
also notify the carrier. Retain the shipping carton and packing material for inspection
by the carrier. After this inspection, we will make arrangements to repair or replace
the unit.

AIMB-U233 User Manual vi

vii AIMB-U233 User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Features .................................................................................................... 2
1.3 Specifications ............................................................................................ 2
1.3.1 System .......................................................................................... 2
1.3.2 Memory ......................................................................................... 2
1.3.3 Input/Output .................................................................................. 2
1.3.4 Graphics........................................................................................ 2
1.3.5 Ethernet LAN ................................................................................ 3
1.3.6 Industrial Features ........................................................................ 3
1.3.7 Mechanical and Environmental Specifications.............................. 3
1.4 Jumpers and Connectors .......................................................................... 4
Table 1.1: Connector / Header List:............................................. 4
1.5 Board Layout: Jumper and Connector Locations...................................... 5
Figure 1.1 Jumper and Connector Locations............................... 5
Figure 1.2 Jumper and Connector Locations............................... 6
1.6 AIMB-U233 Board Diagram ...................................................................... 6
Figure 1.3 AIMB-U233 Board Diagram........................................ 6
1.7 Safety Precautions .................................................................................... 7
1.8 Jumper Options......................................................................................... 7
1.8.1 Setting Jumpers ............................................................................ 7
1.8.2 CMOS Mode Selection (JCOMS1) ............................................... 8
Table 1.2: CMOS Mode Selection (JCOMS1) ............................. 8
1.8.3 LVDS Panel Voltage Selection Header (JLVDS1) ........................ 8
Table 1.3: VDD select for LVDS1 Panel (JLVDS1) ..................... 8
1.8.4 ATX/AT Mode Selection (PSON1) ................................................ 8
Table 1.4: ATX/AT Mode selection (PSON1) .............................. 8
Chapter 2 Connecting Peripherals ......................9
2.1 Introduction ............................................................................................. 10
2.2 LAN and USB Ports (LAN12, USB12/USB34) ........................................ 10
Table 2.1: LAN LED Indicators .................................................. 10
2.3 DC Input Connector (DCIN1) .................................................................. 11
2.4 Serial Ports (COM1, COM2, COM3, COM4)........................................... 11
2.5 Display Port Connector (HDMI 1/2)......................................................... 12
2.6 System Fan (SYSFAN1) ......................................................................... 12
2.7 CPU FAN (CPUFAN1) ............................................................................ 13
2.8 Front Panel Connectors (JFP1) .............................................................. 13
2.8.1 ATX Soft Power Switch (JFP1/RESET) ...................................... 14
2.8.2 Reset (JFP1/RESET).................................................................. 14
2.8.3 HDD LED (JFP1/HDDLED)......................................................... 14
2.8.4 Power LED Header (JFP1/PWR_LED)....................................... 14
Table 2.2: ATX Power Supply LED Status ................................ 14
2.9 HD Audio Interface LINE-OUT / Mic-In (AUDIO1 / AUDIO2) .................. 15
2.10 Serial ATA Interface (SATA1 and SATAPWR1) ..................................... 15
2.11 AT/ATX Mode Selection Connector (PSON1)......................................... 16
2.12 SPI Flash Connector (SPI_CN1)............................................................. 16
2.13 Backlight Inverter Power Connector (INV1) ............................................ 17
2.14 LVDS / eDP Panel Connector (LVDS_EDP1), BOM Options ................. 17
2.15 LVDS Panel Voltage Selection Header (JLVDS1) .................................. 18
2.16 General Purpose I/O Connector (GPIO1) ............................................... 18
2.17 CMOS Battery Connector (BAT1) ........................................................... 19
2.18 DDR4 SODIMM (DIMMA1) ..................................................................... 19

AIMB-U233 User Manual viii
2.19 M.2 M-Key (NGFF_M1) .......................................................................... 20
2.20 M.2 B-Key and SIM slot (NGFF_B1 / SIM1) ........................................... 20
2.21 M.2 E-Key (NGFF_E1)............................................................................ 21
2.22 CMOS Clear Pin Header (JCMOS1)....................................................... 21
2.23 Low Pin Count Header (LPC1) ............................................................... 22
Chapter 3 BIOS Operation ................................. 23
3.1 Introduction ............................................................................................. 24
3.2 BIOS Setup ............................................................................................. 24
3.2.1 Main Menu .................................................................................. 25
3.2.2 Security....................................................................................... 45
3.2.3 Save & Exit ................................................................................. 46
3.2.4 Boot ............................................................................................ 47
Chapter 4 Software and Service Introduction.. 49
4.1 Introduction ............................................................................................. 50
4.2 Value-Added Software Services ............................................................. 50
4.2.1 Software API............................................................................... 50
4.2.2 Software Utility............................................................................ 52
Chapter 5 Chipset Software Installation Utility 53
5.1 Before Installation ................................................................................... 54
5.2 Introduction ............................................................................................. 54
Chapter 6 Graphics Setup ................................. 55
6.1 Introduction ............................................................................................. 56
6.2 Windows 10 ............................................................................................ 56
Chapter 7 LAN Configuration ............................ 57
7.1 Introduction ............................................................................................. 58
7.2 Features.................................................................................................. 58
7.3 Installation............................................................................................... 58
7.4 Windows 10 Driver Setup ....................................................................... 58
Appendix A Pin Assignments............................... 59
A.1 Pin Assignments ..................................................................................... 60
A.1.1 SPI Pin Header (SPI1_CN1)....................................................... 61
A.1.2 ATX 12V power supply connector (ATX12V1)............................ 61
A.1.3 System Fan #1 connector (SYSFAN1) ....................................... 61
A.1.4 DC input Jack (DCIN1) ............................................................... 62
A.1.5 IMVP8/9 PMBus KIT (JPMB1).................................................... 62
A.1.6 HDMI #1 (HDMI1) ....................................................................... 62
A.1.7 AT/ATX Mode selection (PSON1) .............................................. 63
A.1.8 LVDS VESA, JEIDA format selection pin header (JLVDS_VCON1)
63
A.1.9 HDMI #2 (HDMI2) ....................................................................... 63
A.1.10 VDD select for LVDS1 Panel (JLVDS1) ..................................... 64
A.1.11 Low Voltage Differential Signaling / EDP (LVDS_EDP1) ........... 64
A.1.12 Inverter power connector (INV1)................................................. 65

ix AIMB-U233 User Manual
A.1.13 HD Audio Interface (LINE-OUT) (AUDIO1)................................. 66
A.1.14 HD Audio Interface (MIC-IN) (AUDIO2) ...................................... 66
A.1.15 PWRBTN# / RESET# / HDD LED / PWR LED Header (JFP1)... 66
A.1.16 COM1 and COM2 Box Header (COM12) ................................... 67
A.1.17 Serial ATA interface connector #1 (SATA1) ............................... 67
A.1.18 KEY-M connector (NGFF_M1).................................................... 68
A.1.19 M.2 KEY-E connector (NGFF_E1).............................................. 69
A.1.20 Serial ATA Power connector #1 (SATAPWR1)........................... 70
A.1.21 Coin Battery wafer box (BAT1) ................................................... 70
A.1.22 Low pin count interface connector (LPC1).................................. 70
A.1.23 16-bits General Purpose I/O Pin Header (GPIO1)...................... 71
A.1.24 COM3 and COM4 Box Header (COM34) ................................... 71
A.1.25 USB2.0 Front panel Header (USB34)......................................... 72
A.1.26 COMS Mode selection (JCMOS1) .............................................. 72
A.1.27 USB3.1 GEN2 Stack connector (USB12) ................................... 73
A.1.28 Dual port RJ45 Connector (LAN1+LAN2)................................... 73
A.1.29 M.2 KEY-B (NGFF_B1)............................................................... 74
A.1.30 SIM Card holder (SIM1) .............................................................. 75
A.1.31 DDR4 SO-DIMM Socket CH-A (DIMMA1) .................................. 75
A.1.32 CPU FAN #1 connector (CPUFAN1) .......................................... 75

AIMB-U233 User Manual x

Chapter 1
1General Information

AIMB-U233 User Manual 2
1.1 Introduction
AIMB-U233 is the newest UTX small form factor motherboard equipped with Intel®
8th Gen Core™ i3-8145UE/i5-8365UE/i7-8665UE processors and DDR4 2400 MHz
up to 16 GB. The palm-sized industrial motherboard measures 137 x 112mm and
offers fast graphics and media performance to support triple display output via 2 x
HDMI1.4b, eDP (or LVDS), and 2 x 10/100/1000 Mbps Ethernet ports offering high-
speed networking.
AIMB-U233 offers high speed, multiple I/O connectivity and expansion, including 2
USB3.2 Gen2 x1, 4 x COMs (2 RS-232, 2 RS-232/422/485), 1 x SATAIII 6 x GB/s
connector, and 3 x M.2 (1 x M.2 E-Key, 1 x M.2 B-Key, 1 x M.2 M-Key NVMe) expan-
sion slots for easy integration, and an TPM2.0 security feature.
All the features described above are incorporated into a space-saving, power-effi-
cient, and cost-effective UTX small form factor.
1.2 Features
Supports Intel® 8th Gen Core™ i3-8145UE/i5-8365UE/i7-8665UE processors
1 x SO-DIMM Up to 16 GB DDR4 2400 MHz SDRAM
Supports 1 x eDP (LVDS co-lay), 2 x HDMI, 3 Independent Displays
Supports 2 x LAN, 2 x USB3.2 Gen2 x1 Type-A Ports, 4 COM Ports (RS-232/
422/485, selected via BIOS)
Supports 1 x M.2 E-Key, 1 x M.2 B-Key, 1 x M.2 M-Key NVMe
Onboard TPM 2.0 support
Supports Intel vPro (For i5 and i7 CPU)
Supports RAID 0/1/5
Palm size 137mm x 112 mm
1.3 Specifications
1.3.1 System
CPU: Intel® 8th Gen Core™ i3-8145UE/i5-8365UE/i7-8665UE
BIOS: 256 Mb SPI AMI BIOS
SATA hard disk drive interface: One onboard SATA connectors with a data
transmission rate of up to 6 Gb/s
1.3.2 Memory
RAM: 1 x SO-DIMM DDR4 2400 MHz up to 16 GB
1.3.3 Input/Output
M.2 Expansions: Supports 1 x M.2 E-Key (2230), 1 x M.2 B-Key (2242/3042), 1
x M.2 M-Key (2280 SATA or PCIe x4 NVME SSD)
Serial ports: Four serial ports; COM1 & COM3 RS-232, COM2 RS-232/422/
485 (Selected via BIOS) or COM4 RS-232/422/485 (Selected via BIOS)
USB port: Supports 2 x USB3, 2 x Type-A Gen2 x1, 2 x USB2.0 internal pin
header
GPIO connector: One 16-bit general purpose input/output
1.3.4 Graphics
Controller: Intel Gen 9 graphics engine

3 AIMB-U233 User Manual
Chapter 1 General Information
HDMI: Supports up to 3840 x 2160 @ 30 Hz
LVDS: Supports 24-bit dual channel and up to 1920 x 1200, colay eDP (LVDS is
BOM optional)
eDP: Supports up to 4096x2304@60 Hz, colay with LVDS
Triple display: 2 HDMI + eDP (or LVDS)
1.3.5 Ethernet LAN
Supports up to 2 10/100/1000 Mbps Ethernet port (s) via PCI Express x1 bus,
which provides a data transmission rate of 500 MB/s
Controller: LAN1: Intel Jacksonville: I219LM GbE PHY; LAN2: Intel Springville:
I211AT GbE
1.3.6 Industrial Features
Watchdog timer: Can generate a system reset. The watchdog timer is pro-
grammable, with each unit equal to one second or one minute (255 levels)
1.3.7 Mechanical and Environmental Specifications
Operating temperature: 0~60 °C (32~140 °F) with air flow 0.7 m/s
Storage temperature: -40 ~ 85 °C (-40 ~ 185 °F)
Humidity: 5 ~ 95% non-condensing
Power supply voltage: +12 V
Power consumption:+12 V, Windows Idle mode: 6.236 W (i7-8665UE with 16
GB SO-DDR4-2666) Windows Max Load: 22.971 W (i7-8665UE with 16 GB
SO-DDR4-2666)
Board size: 112 x 137 mm (4.4" x 5.4")
Board weight: 3.5 kg

AIMB-U233 User Manual 4
1.4 Jumpers and Connectors
The AIMB-U233 motherboard is equipped with connectors for linking the board to
external devices such as hard disk drives. The board also features several jumpers
for configuring the system according to specific applications.
The function of each board jumper and connector is listed in the table below. The pro-
cedure for setting jumpers is explained in subsequent sections of this chapter.
Instructions for connecting external devices to the motherboard are provided in
Chapter 2.
Table 1.1: Connector / Header List:
Description Part Reference
1 SPI Pin Header SPI1_CN1
2 ATX 12V power supply connector ATX12V1
3 System Fan #1 connector SYSFAN1
4 DC input Jack DCIN1
5 IMVP8/9 PMBus KIT JPMB1
6 HDMI #1 HDMI1
7 AT/ATX Mode selection PSON1
8 LVDS VESA, JEIDA format selection pin header JLVDS_VCON1
9 HDMI #2 HDMI2
10 VDD select for LVDS1 Panel JLVDS1
11 Low Voltage Differential Signaling / EDP LVDS_EDP1
12 Inverter power connector INV1
13 HD Audio Interface (LINE-OUT) AUDIO1
14 HD Audio Interface (MIC-IN) AUDIO2
15 PWRBTN# / RESET# / HDD LED / PWR LED JFP1
16 COM1 and COM2 Box Header COM12
17 Serial ATA interface connector #1 SATA1
18 M.2 KEY-M connector NGFF_M1
19 M.2 KEY-E connector NGFF_E1
20 Serial ATA Power connector #1 SATAPWR1
21 Coin Battery wafer box BAT1
22 Low pin count interface connector LPC1
23 16-bits General Purpose I/O Pin Header GPIO1
24 COM3 and COM4 Box Header COM34
25 USB2.0 Front panel Header USB34
26 COMS Mode selection JCMOS1
27 USB3.1 GEN2 Stack connector USB12
28 Dual port RJ45 Connector LAN1+LAN2
29 M.2 KEY-B connector NGFF_B1
30 Nano SIM Card holder SIM1
31 DDR4 SO-DIMM Socket CH-A DIMMA1
32 CPU FAN #1 connector CPUFAN1

5 AIMB-U233 User Manual
Chapter 1 General Information
1.5 Board Layout: Jumper and Connector
Locations
Figure 1.1 Jumper and Connector Locations

AIMB-U233 User Manual 6
Figure 1.2 Jumper and Connector Locations
1.6 AIMB-U233 Board Diagram
Figure 1.3 AIMB-U233 Board Diagram

7 AIMB-U233 User Manual
Chapter 1 General Information
1.7 Safety Precautions
1.8 Jumper Options
This section provides instructions on how to configure the motherboard by setting
jumpers and also outlines the default motherboard settings and options for each
jumper.
1.8.1 Setting Jumpers
The motherboard can be configured according to the application requirements with
the setting of jumpers. A jumper is a metal bridge used to close an electrical circuit.
Jumpers typically consist of two metal pins and a small metal clip (often protected by
a plastic cover) that slides over the pins to connect them. To “close” (or turn ON) a
jumper, connect the pins with the clip. To “open” (or turn OFF) a jumper, simply
remove the clip. Some jumpers comprise a set of three pins, labeled 1, 2, and 3. With
these jumpers, simply connect either Pins 1 and 2, or Pins 2 and 3. A pair of needle-
nose pliers may be necessary for setting jumpers.
Warning! Always completely disconnect the power cord from the chassis when
working with the hardware. Do not connect devices while the power is
on. Sensitive electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should open the PC
chassis.
Caution! Always ground yourself to remove any static charge before touching the
motherboard. Modern electronic devices are very sensitive to electro-
static discharges. As a safety precaution, use a grounding wrist strap at
all times. Place all electronic components on a static-dissipative surface
or in a static-shielded bag when not in the chassis.
Caution! The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer's
instructions.
Caution! There is a danger of a new battery exploding if incorrectly installed. Do
not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer’s
instructions.

AIMB-U233 User Manual 8
1.8.2 CMOS Mode Selection (JCOMS1)
1.8.3 LVDS Panel Voltage Selection Header (JLVDS1)
1.8.4 ATX/AT Mode Selection (PSON1)
Table 1.2: CMOS Mode Selection (JCOMS1)
Function Jumper Setting
Normal (Default)
Clear CMOS Data
Table 1.3: VDD select for LVDS1 Panel (JLVDS1)
Function Jumper Setting
Jumper position for +3.3 V (Default)
Jumper position for +5 V
Jumper position for +12 V
Table 1.4: ATX/AT Mode selection (PSON1)
Function Jumper Setting
AT Mode (Default)
ATX Mode

Chapter 2
2Connecting
Peripherals

AIMB-U233 User Manual 10
2.1 Introduction
Most of the device connectors can be accessed from the top of the board during
installation in the chassis. If the system is installed with several cards or the chassis
is packed, partial removal of the card may be necessary to make all connections.
Please refer to the Appendix if you need more detailed information regarding the con-
nectors and pin definitions.
2.2 LAN and USB Ports (LAN12, USB12/USB34)
AIMB-U233 provides 2 USB3.2 Gen2 x1 which are located on the rear side. The USB
interface complies with the USB specification revision 3.2 that supports transmission
rates of up to 10 Gbps and 2 x USB2.0 internal pin header that supports 480 Mbps.
The AIMB-U233 system is equipped with 2 high-performance 1000 Mbps Ethernet
LAN adapters. All of them are supported by all major network operating systems. The
RJ-45 jacks on the rear panel facilitate a convenient LAN connection.
Table 2.1: LAN LED Indicators
LAN Mode LAN Indicator
1 Gbps link on LED1 Green on
100 Mbps link on LED1 Orange on
Active LED2 Green flashing