Advantech MIC-3329 Series User manual

User Manual
MIC-3329
3U CompactPCI Intel®
Quad-Core Atom™ Processor
Blade with ECC support

MIC-3329 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2019
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel® and Pentium® are trademarks of Intel Corporation.
Microsoft® Windows® and MS-DOS® are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No. 2002332900 Edition 1
Printed in China April 2019

iii MIC-3329 User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
FM
This equipment has passed the FM certification. According to the National Fire Pro-
tection Association, work sites are classified into different classes, divisions and
groups, based on hazard considerations. This equipment is compliant with the speci-
fications of Class I, Division 2, Groups A, B, C and D indoor hazards.
Technical Support and Assistance
1. Visit the Advantech website at http://support.advantech.com where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

MIC-3329 User Manual iv
Warnings, Cautions and Notes
Document Feedback
To assist us in making improvements to this manual, we would welcome comments
and constructive criticism. Please send all such - in writing to: support@advan-
tech.com
Packing List
Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.
MIC-3329 all-in-one single board computer (CPU heatsink) x1
SATA Daughter board for SATA bracket (Assembled) x 1
HDD screws x 4 or CFast screw x 1 (Accessories)
Warranty certificate document x1, China Rohs List document x1 (Accessories)
Safety Warnings: CE, FCC class A
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately.
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.
Note! Notes provide optional additional information.

v MIC-3329 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

MIC-3329 User Manual vi
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush
of power, or electrostatic discharge, as you connect a jumper or install a card
may damage sensitive electronic components.
We Appreciate Your Input
Please let us know of any aspect of this product, including the manual, which could
use improvement or correction. We appreciate your valuable input in helping make
our products better

vii MIC-3329 User Manual
Contents
Chapter 1 Hardware Configuration......................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 3
1.2.1 CompactPCI Bus Interface ........................................................... 3
1.2.2 CPU .............................................................................................. 3
1.2.3 BIOS ............................................................................................. 3
1.2.4 Memory ......................................................................................... 3
1.2.5 Ethernet and VGA......................................................................... 3
1.2.6 Storage Interface .......................................................................... 3
1.2.7 Serial Interface.............................................................................. 4
1.2.8 USB Port ....................................................................................... 4
1.2.9 LEDs ............................................................................................. 4
Table 1.1: LED Indicator for the MIC-3329.................................. 4
1.2.10 Watchdog Timer............................................................................ 4
1.2.11 Optional Rear I/O Modules ........................................................... 4
Table 1.2: MIC-3329 RIO Configurations .................................... 4
1.2.12 Mechanical and Environmental Specifications.............................. 5
1.2.13 CompactPCI Mechanical Design .................................................. 5
1.2.14 CompactPCI Bridge ...................................................................... 5
1.2.15 I/O Connectivity............................................................................. 6
1.2.16 XTM Connectors (Extension Module) ........................................... 6
1.2.17 LPC UART Controller.................................................................... 6
1.2.18 RTC and Battery ........................................................................... 6
1.3 Functional Block Diagram ......................................................................... 6
Figure 1.1 MIC-3329 Front 4HP Function Block Diagram ........... 6
Figure 1.2 MIC-3329 Front 8HP XTM Function Block Diagram... 7
Figure 1.3 MIC-3329 Front 8HP XTM-2 Functional block diagram
7
Figure 1.4 MIC-3329 RIO 4HP and XTM Function Block Diagram
7
1.4 Jumpers and Switches .............................................................................. 8
Table 1.3: MIC-3329 Switch Descriptions ................................... 8
Figure 1.5 MIC-3329 Front 4HP Board Jumper Locations .......... 8
Figure 1.6 MIC-3329 Front 8HP XTM Board Jumper Locations.. 9
Figure 1.7 MIC-3329 Rear 8HP XTM Board Jumper Locations 10
1.4.1 Clear CMOS (JP2) ...................................................................... 10
1.5 Connector Definitions.............................................................................. 11
Table 1.4: MIC-3329 Connector Descriptions ........................... 11
Figure 1.8 MIC-3329 Front Panel .............................................. 11
Figure 1.9 MIC-3329 8HP Oblique View.................................... 12
Table 1.5: MIC-3329 RIO Connector Descriptions .................... 12
Figure 1.10MIC-3329 RIO Front Panel Ports ............................. 13
Figure 1.11MIC-3329 RIO 8HP Oblique View ............................ 13
1.6 Safety Precautions .................................................................................. 13
1.7 Installation Steps..................................................................................... 14
Figure 1.12Complete Assembly of MIC-3329 Dual Slot with SATA
HDD.......................................................................... 14
1.8 Software Support .................................................................................... 14
Chapter 2 AMI BIOS Setup .................................15
2.1 Introduction ............................................................................................. 16
Figure 2.1 Setup Program Initial Screen.................................... 16
2.2 BIOS Setup ............................................................................................. 17

MIC-3329 User Manual viii
2.2.1 Entering Setup ............................................................................ 17
Figure 2.2 Press <DEL> or <F2> to Run Setup ........................ 17
2.2.2 Main Setup.................................................................................. 18
Figure 2.3 Main Setup Screen................................................... 18
2.2.3 Advanced BIOS Features Setup................................................. 19
Figure 2.4 Advanced BIOS Features Setup Screen.................. 19
Figure 2.5 H/W Monitor PC Health Status................................. 20
Figure 2.6 Super IO Configuration............................................. 21
Figure 2.7 Serial Port Console Redirection ............................... 22
Figure 2.8 CPU configuration .................................................... 23
Figure 2.9 PPM configuration .................................................... 24
Figure 2.10IDE configuration...................................................... 25
Figure 2.11PCI Setting ............................................................... 26
Figure 2.12Network Stack configuration..................................... 27
Figure 2.13CSM configuration.................................................... 28
Figure 2.14USB configuration .................................................... 29
Figure 2.15Security configuration............................................... 30
2.2.4 Chipset Configuration Setting ..................................................... 31
Figure 2.16Chipset Setup Screen .............................................. 31
Figure 2.17South Bridge Configuration ...................................... 32
Figure 2.18North Bridge Configuration....................................... 33
Figure 2.19Intel IGD configuration.............................................. 34
2.2.5 Boot Settings .............................................................................. 35
Figure 2.20Boot Settings ............................................................ 35
2.2.6 Security Settings......................................................................... 36
Figure 2.21Security Settings ...................................................... 36
Figure 2.22HDD Security Configuration ..................................... 37
2.2.7 Save and Exit Configuration ....................................................... 38
Figure 2.23Save and Exit ........................................................... 38
Appendix A Pin Assignments............................... 41
A.1 J1 Connector........................................................................................... 42
Table A.1: J1 Compact PCI Pin Definitions ............................... 42
A.2 J2 Connector........................................................................................... 43
Table A.2: J2 Compact PCI Pin Definitions ............................... 43
Appendix B Programming the Watchdog Timer .45
B.1 Watchdog Timer Programming Procedure ............................................. 46
Appendix C Embedded Controller ....................... 49
C.1 Features.................................................................................................. 50
C.2 I/O Registers ........................................................................................... 50
Table C.1: LPC I/O Register Addresses .................................... 50
Table C.2: LPC I/O Register Addresses .................................... 50
Appendix D Glossary............................................. 51
D.1 Glossary.................................................................................................. 52

Chapter 1
1Hardware
Configuration
This chapter describes how to
configure MIC-3329 hardware.

MIC-3329 User Manual 2
1.1 Introduction
Advantech MIC-3329 Series uses the latest Intel®22 nm Atom™ technology to pro-
vide significant performance and power efficiencies.
MIC-3329 series are 3U CompactPCI®processor blades, with dual-quad E3826/
E3827 and quad-core E3845 Atom™ SOC processors, with up to 4GB soldered
DDR3L-1333 ECC memory. They are available in single and dual slot width form fac-
tors, to offer various I/O functionality by XTM (8HP) and rear I/O extensions. Front
panel I/O on the single slot (4HP) provides 2 x RJ45 GbE ports (switchable with RIO
4HP),1 x VGA port (switchable with RIO 4HP), 1 x USB2.0 port and 1 x USB3.0 port.
Front panel I/O on the second layer provides XTM-1 2 x COM ports (RS232/422/
485), 1 x PS/2 KB/MS and 1 x audio ports or XTM-2: 2 X-Code GbE ports, 1xDB9
COM ports (RS232/422/485). There are three types of storage devices available,
such as on board 8GB SSD flash, Cfast and 2.5" SATA connector.
MIC-3329 provides an ideal solution for transportation, railway, and factory automa-
tion applications. With its robust board layout and thermal efficiency, it meets or
exceeds EN50155 and EN50121-4; it provides a very low processor TDP of 8W/10W,
and its low power consumption and industrial SOC features make it a perfect fit for all
fanless system applications.
Ordering Information
Front/Rear Panel
4HP 8HP XTM
RJ45
LAN (1) USB2.0 USB3.0 VGA(2) CPU M12 LAN COM Audio PS/2 SATA Conn.
Cfast
Socket(3)
P/N List Front
Board
MIC-3329A1-
D2E 2111E382621NANA11
MIC-3329C1-
D2E 2111E384521NANA11
MIC-3329B1-
D1E 2111E3827NA2111NA
MIC-3329C1-
D1E 2111E3845NA2111NA
P/N List RIO
Board
MIC-3329R1-
D1E 2 2 NA 1 NA NA 2 NA NA NA 1
Note! (1)(2): 2xLAN and 1xVGA are switchable between front and RIO board
(3): MIC-3329R1-D1E Cfast socket is only active in MIC-3329B1-D1E/
MIC-3329C1-D1E

3 MIC-3329 User Manual
Chapter 1 Hardware Configuration
1.2 Specifications
1.2.1 CompactPCI Bus Interface
The MIC-3329 is compliant with PICMG 2.0 Rev. 3.0. It supports a 32-bit / 33 MHz
PCI bus for up to 8 CompactPCI slots. The MIC-3329 is hot-swap compliant (PICMG
2.1). The board can be configured as a system master or a drone board. In drone
mode, it only draws power from the CompactPCI backplane and is not active on the
Compact-PCI bus.
1.2.2 CPU
The MIC-3329 supports the 22nm technology quad-core Intel®Atom™ E3845 and
dual-core Intel®Atom™ E3827/E3826 SOC processors with clock frequencies up to
1.91GHz. Supported processors are listed in the table below. Forced airflow cooling
is required.
1.2.3 BIOS
Dual 8Mb SPI flash contains a board-specific BIOS (from AMI) designed to meet
industrial and embedded system requirements.
1.2.4 Memory
The MIC-3329 has up to 4 GB onboard soldered DDR3L memory with ECC support.
Default SKU is 4GB on board, if you have any 2GB cost-effective SKU request,
please contact you local salesperson for more information.
1.2.5 Ethernet and VGA
The MIC-3329 uses two Intel®I210AT controllers to provide 10/100/1000 Mbps
Ethernet connectivity. These are mutually exclusive and can be either:
Front I/O (RJ-45)
Rear I/O (Rear Transition Module)
User can access LAN1/LAN2 and VGA via front panel or rear panel by setting an on-
board switch.
1.2.6 Storage Interface
The MIC-3329 supports two SATA II interfaces. XTM-1 supports 2.5" SATA, XTM-2
supports 2.5" SATA and Cfast. 8G on board NAND flash is not a standard SKU, but is
available by customer request.
Intel CPU
Model NO. Cores Freq. CPU architecture Memory L2 Cache CPU TDP
E3845 4 1.91 GHz 22nm DDR3L
1333 2 MB 10W
E3827 2 1.75 GHz 22nm DDR3L
1333 1 MB 8W
E3826 2 1.46GHz Baytrail (22nm) DDR3L
1066 1 MB 7W

MIC-3329 User Manual 4
1.2.7 Serial Interface
Four serial ports from LPC UART controller, two DB9 COM1/COM2 ports (RS-232/
422 interface) are provided on the front panel. Another two COM ports (RS-232/422/
485 interface) are routed to the rear I/O module as a DB9 port via the J2 connector.
1.2.8 USB Port
Three USB 2.0 compliant ports are provided. One USB3.0 and one USB2.0 port are
routed to front panel connectors; two USB2.0 ports are routed to the rear I/O through
the J2 connector.
1.2.9 LEDs
Four LEDs are provided on the front panel as follows:
1.2.10 Watchdog Timer
An onboard watchdog timer provides system reset capabilities via software control.
The programmable time interval is from 1 to 255 seconds.
1.2.11 Optional Rear I/O Modules
The MIC-3329R is the rear I/O module, reserved for the MIC-3329 extension. It offers
a wide variety of I/O features, such as two USB2.0 and two DB9 COM ports. Rear I/O
module key features are shown below:
Table 1.1: LED Indicator for the MIC-3329
Function Color Indicator LED Status
Hotswap LED Blue The board can be safely removed from system
when blue LED is on
HDD LED Yellow HDD is active
Power LED Green Power is provided to the board.
Master/Drone
mode LED Green LED On-> “Master” mode. LED Off-> “Drone” mode.
Table 1.2: MIC-3329 RIO Configurations
Rear Panel
LAN(1) VGA(1) COM USB2.0 Slot width Conn.
MIC-3329R1-D1E 2 1 2 2 2 J2
Note! LAN port and VGA port may be switched to front panel I/O ports via
hardware switch.

5 MIC-3329 User Manual
Chapter 1 Hardware Configuration
1.2.12 Mechanical and Environmental Specifications
Operating temperature: -40 ~ 70 °C (-40 °F ~ 158 °F)
Storage Temperature: -40 ~ 85 °C (-40 ~ 185 °F)
Humidity: 95% @ 40 °C (non-condensing)
Humidity (Non-operating): 95% @ 60 °C (non-condensing)
Vibration: 5 ~ 100Hz, 2.0 Grms with CFast/SSD (without on-board 2.5" SATA
HDD)
Vibration (Non-operating): 5 ~ 500Hz, 2 Grms
Shock: 10 G (without on-board 2.5” SATA HDD), 11ms
Shock (Non-operating): 30 G, 11ms (On dual slot SKU)
Board size:
3U/2 slot width (8HP): 100 x 160 x 40 mm
Weight:
3U/2 slot width (Front Board 8HP): 0.3 kg (bare board)
3U/2 slot width (Rear Board 8HP): 0.4 kg (bare board)
1.2.13 CompactPCI Mechanical Design
MIC-3329 series is assembled with an aluminium CPU heatsink.
1.2.14 CompactPCI Bridge
The MIC-3329 uses a Pericom PI7C9 universal bridge as a gateway to an intelligent
subsystem. When configured as a system controller, the bridge acts as a standard,
transparent PCI Express to PCI/PCI-X bridge. As a peripheral controller it allows the
local MIC-3329 processor to configure and control the onboard local subsystem inde-
pendently from the CompactPCI bus host processor. The MIC-3329 local PCI sub-
system is presented to the CompactPCI bus host as a single CompactPCI device.
When the MIC-3329 is in drone mode, the Pericom PI7C9 is electrically isolated from
the CompactPCI bus. The MIC-3329 receives power from the backplane, and sup-
ports the rear I/O. The Pericom PI7C9 PCI bridge offers the following features:
PCI Interface
Full compliance with the PCI Local Bus Specification, Revision 3.0; operations
are transparent.
Supports forward bridging
32-bit, 33MHz asynchronous operation
Provides two level arbitration support for 7 x PCI bus masters
16-bit address decode for VGA
Usable in CompactPCI system slot
For further detail, please consult the Pericom PI7C9 data book.
Note! The operating temperature range of the MIC-3329 depends on the
installed processor and the airflow through the chassis. For extended
temperature products please contact your Advantech representative.

MIC-3329 User Manual 6
1.2.15 I/O Connectivity
For MIC-3329, the front panel I/O is provided with two RJ-45 Gigabit Ethernet ports,
two DB9 COM ports, one USB 2.0 port, one USB 3.0 port, one VGA port, 1 audio port
and 1 PS/2 port. Onboard I/O consists of two SATA channels, one is for the 2.5" on
board SATA connector or Cfast socket, the other one is for on board NAND flash or is
routed to rear transition module as RIO onboard cfast socket. Rear I/O connectivity is
available via the following CompactPCI connectors:
J2: two Gigabit Ethernet LAN ports, two USB2.0 ports, one VGA port on 4HP,
two COM ports on the XTM of RTM.
1.2.16 XTM Connectors (Extension Module)
MIC-3329 is extended by a XTM board with two COM ports, one PS/2, one KB/MS
port and one onboard SATA or Cfast connector.
1.2.17 LPC UART Controller
One UART controller F81216 is available for four UART interfaces.
1.2.18 RTC and Battery
The RTC module uses a a CR2032(3 V, 210 mAH) battery to maintain system date
and time.
1.3 Functional Block Diagram
Figure 1.1 MIC-3329 Front 4HP Function Block Diagram
SATA2.0
J2
DDR3L 1333Hz
onboard w/ECC
Up to 4GB
LA N2
LA N1
USB 1
VG A
PCIex1
I210-AT
EC
Handle SW
Re set SW
User LEDs
SPI
PCIe 2 PCI
PI7C9x1 10
PCI 32bit s 3 3 MHz
PCIex1
J1
Hot Swap
Controller
+5 V,
8HP
LP C
BIOS
I210-AT
VG A
PCIex1
Front panel
LPC
Bay Trail+ ECC (BGA)
Atom
E3827 dual cores 8W
(-40~110C)
Atom
E3 845 quad cor e 10 W
(-40~110C)
1X USB 3.0
Mux to J2
VGA
LAN1
LAN2
UART(2x)
Front
panel 1
CO M1
CO M2
PS /2
Mux to J 2
US B 2.0 ( x1 )
BIOSx2
LPC
AUDIO
Audio
F8 1216
HWM
U AR T(2 x) RS 23 2, 422 ,4 85
J2 VG A
USB 2
1X USB 2. 0
J2
U AR T(2 x) R S 232 ,4 22 ,48 5
SSD*
8Gb
Mux
Mux
SA TA2 .0
USB 2.0 (x1)
PS/ 2

7 MIC-3329 User Manual
Chapter 1 Hardware Configuration
Figure 1.2 MIC-3329 Front 8HP XTM Function Block Diagram
Figure 1.3 MIC-3329 Front 8HP XTM-2 Functional block diagram
Figure 1.4 MIC-3329 RIO 4HP and XTM Function Block Diagram
PS /2
8HP
U AR T(1 x) RS 23 2,4 22 ,48 5
SATA2.0 (1x)
U AR T(1 x) RS 23 2,4 22 ,48 5
Isolated
COM1
Isolated
COM2
2.5” SATA
Audio
PS/2
Front panel
=> Rich I/O & Storage:
1xPS/2
2xCOM (RS232/422/485)
1x Cfast Socket or 1x on board
SATA by BOM option
=> Isolated COM port design
reserved for railway /
Electricity application
Mux
BO M O pti on
Cfast
PCIex1 PCIEx1
PCIex1
8HP-2
UART(1x) RS232,422,485
SATA2.0 (1x)
UART(1x) RS232,422,485
COM1
COM2
2.5” SATA
Front panel
=> Rich I/O & Storage:
1xCOM (RS232/422/485)
1x Cfast Socket
1x on board SATA
=> COM port design
reserved for railway /
Electricity application
Cfast
SATA2.0 (1x)
M12 *2 PI7C9X
2G304
2x
I210
Rich I/O Extension
Isolated COM port design reserved for railway / Electricity application
Isol at ed
COM B
RIO 8HP Panel
Isol at ed
COM A
UART(1x) RS232,422,485
UART(1x) RS232,422,485
8HP
LAN B
J2
RIO 4HP Panel
USB A
LAN A
USB B
VGA
Mux to front
To 8HP I s ola ted C OM B
I s ola ted C OM A
VGA (x1)
USB2.0 (x1)
USB Hub
USB2.0
USB2.0 (x1)
USB2.0 (x3)
To 8HP
Cfast SATA 2.0 (Mux to front)
Mux to front
Mux
BOM
Option

MIC-3329 User Manual 8
1.4 Jumpers and Switches
Table 1.4 lists the jumper and switch functions. Refer to this section carefully before
changing the jumper and switch settings on your MIC-3329 board.
Figures 1.4 through 1.6 illustrate jumper and switch locations.
The MIC-3329 provides a system reset button on the front panel, it resets all payload
and application-related circuitry.
Figure 1.5 MIC-3329 Front 4HP Board Jumper Locations
Table 1.3: MIC-3329 Switch Descriptions
Board Position Description Default Setting
MIC-3329
Front 4HP
Board
CN3 Battery pin head
SW1 DIP Switch for setting LAN1/2 and
VGA as front or rear Front VGA/LAN1 LAN2
MIC-3329
Front 8HP
XTM Board
SW3/SW4 DIP Switch for COM 232/422/485
setting (4 code for SP338)
Default setting RS232;
RS422/RS485 setting refer
to silkscreen on PCB top
side
SW5/SW6/
SW7/SW8 Control COM workable or not Always setting "ON", refer to PCB bottom side
MIC-3329
RIO 8HP
XTM Board
SW3/SW4 DIP Switch for COM 232/422/485
setting (4 code for SP338)
Default setting RS232;
RS422/RS485 setting refer
to silkscreen on PCB top
side

9 MIC-3329 User Manual
Chapter 1 Hardware Configuration
Figure 1.6 MIC-3329 Front 8HP XTM Board Jumper Locations
MIC-3329 Front 4HP Board SW1 Setting
Front LAN1/2&VGA(Default):
1 set to "OFF" is Front VGA
2 set to "ON" is Front LAN1/2
Rear LAN1/2&VGA:
1 set to "ON" is Rear VGA
2 set to "OFF" is Rear LAN1/2
MIC-3329 Front 8HP XTM Board SW5, SW6, SW7, SW8,Setting
Control COM workable, always set to "ON"
MIC-3329 Front 8HP XTM Board SW3, SW4 Setting
RS232 (default)
1 set to "ON"
RS422
1 set to "ON",
2 set to "ON"
RS485
2 set to "ON"

MIC-3329 User Manual 10
Figure 1.7 MIC-3329 Rear 8HP XTM Board Jumper Locations
1.4.1 Clear CMOS (JP2)
This jumper is used to erase CMOS data. MIC-3329 Clear CMOS can erase “user
password and time” information only since we implement CMOS backup mechanism
in case of user data loss when battery power is exhausted.
MIC-3329 Front 8HP XTM Board SW3, SW4 Setting
SW3, SW4 RS232(Default)
1 set to "ON"
SW3, SW4 RS422
1 set to "ON"
2 set to "ON"
SW3, SW4 RS485
2 set to "ON"

11 MIC-3329 User Manual
Chapter 1 Hardware Configuration
1.5 Connector Definitions
Table 1.5 and Table 1.6 list the functions of each connector of MIC-3329 and its RIO,
Figures 1.7 and 1.8 illustrate connector locations.
Figure 1.8 MIC-3329 Front Panel
Table 1.4: MIC-3329 Connector Descriptions
Number Function
J1/J2 Primary CompactPCI bus
CN1 Board to board connector on 4HP
CN7 Board to board connector on XTM
CN3 SATA2.0 on board connector on XTM

MIC-3329 User Manual 12
Figure 1.9 MIC-3329 8HP Oblique View
Table 1.5: MIC-3329 RIO Connector Descriptions
MIC-3329R1-D1E
Number Function
RJ1/RJ2 Rear I/O transition
CN3 Cfast connector
CN5 CN6 Board to board connector