Advantech MIO-3360 Installation and operation manual

MIO-3360 Startup Manual 1
Before you begin installing your card, please make sure
that the following items have been shipped:
1. 1 MIO-3360 SBC
2. 1 Startup Manual
3. 1 Heatsink p/n: 1960078695T101
4. Screw and stud pack (2 screws
for Mini PCIe, 4 M3 studs and
screws for heatsink) p/n: 9666226300E
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1: For detailed contents of MIO-3360, please refer
to Advantech website.
Note 2: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded
at: http://get.adobe.com/reader/ (Acrobat is
a trademark of Adobe)
Note 3: Default BIOS is supported for 64 bit OS installa-
tion, BIOS for 32 bit OS is supported by project,
please contact with sales representative for
details.
MIO-3360 Intel®Pentium N4200/Celeron N3350
Pico-ITX SBC, DDR3L, 48-bit LVDS, VGA,DP/HDMI,
1 GbE, Full-size Mini PCIe, 4 USB, 2 COM, SMBus,
mSATA & MIOe
Startup Manual
General
• CPU: Intel®Pentium N4200, 1.10 GHz, Quad-core/
Intel® Celeron N3350, 1.10 GHz, Dual-core
• System Memory: 1 x 204-pin SODIMM socket DDR3L
1866 MHz, up to 8 GB
• L2 Cache: 2 MB
• BIOS: AMI EFI 64 Mbit Flash ROM
• Watchdog Timer: 255 level interval timer
• Battery: Lithium 3 V/210 mAH
Note: How to clear CMOS (Must follow steps below):
1. Turn off system power.
2. Unplug CR2032 battery cable on BH1.
3. Waiting for 15 sec or short BH1 pin1-2.
4. Connect battery cable on BH1.
5. Turn on system power.
• Serial ATA: One SATA III interface, up to 600 MB/s
• USB: 4 USB 2.0
• Audio: High definition audio (HD), line-in, line-out
• GPIO: 8-bit general purpose input/output
• Expansion Interface: Full size Mini PCIe
MIOe Expansion Slot
• Interface: SMBus, USB3.0, LPC, 2 x PCIe x1, Line out,
DisplayPort/HDMI*, +5 Vsb/+12 Vsb power, Power On,
Reset
• Total peripheral power supply output: 5V @ 3A for
CPU board and MIOe module totally, 12V @ 2A for MIOe
module
VGA/HDMI Interface
• Controller: Intel®SoC N3350, DirectX 11 and
OpenGL3.0 support for VGA and HDMI display 48 bit
LVDS display output
• Output Interfaces:
- VGA: Up to 1920 X 1200 at 60 Hz
- HDMI: Up to 3840 x 2160 at 30Hz
- LVDS: Single channel 48-bit LVDS,
up to 1920 x 1200 at 60Hz
- Dual Display: LVDS+VGA or LVDS+DP/HDMI or
VGA+DP/HDMI
Ethernet Interface
• Supports single 10/100/1000 Mbps Ethernet interface
• Controller: Intel® i210
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://service.advantech.com.tw/support/
This manual is for the MIO-3360 Series Rev. A1
Part No. 2006O33600
Printed in China
1st Edition
April 2018

2 MIO-3360 Startup Manual
Mechanical and Environmental
• Dimensions: 100 x 72 mm (3.9” x 2.8”)
Mechanical Drawings are on page 4 - 6.
• Power Requirement: Single 12 V ± 10% DC power input
• Power Consumption (with 8 GB memory):
- Typical in Window 10:
Idle mode
N3350: 0.37 @ 12V (4.48W)
- Max in HCT:
Max. load
N3350: 1.44 @ 12V (17.38W)
Operating Temperature: 0 ~ 60° C (32 ~ 140° F)
• Weight: 0.39 kg (0.85 lb), weight of total package
The board has a number of jumpers that allow you to configure
your system to suit your application. The table below lists the
function of each of the jumpers and connectors.
Jumpers
Label Function
J1 LCD Power / Auto Power on
J2 Mini PCIE/ mSATA Select
Connectors
Label Function
CN4 64Pin Connector A
CN5 DDR3L SO-DIMM
CN10 Mini PCIE
CN11 SATA
CN18 MIOe
CN26 Battery
CN28 12V Power Input
CN29 64Pin Connector B
CN30 VGA
CN31 Inverter Power Output
CN32 Internal USB
CN33 LAN
CN34 48-bit LVDS Panel
Jumpers and Connectors
Jumpers and Connectors
Specications Cont.
Jumper Settings
J1
LCD Power Selection
Setting
Function
(1-2) +5 V
(3-4)* +3.3 V
(5-6)* Auto Power On
* default
J2
Mini PCIE/ mSATA Select
Setting
Function
(Close)* +Mini PCIE
(Open) mSATA
* default
Open Closed
Caution! The computer is provided with a battery-pow-
ered real-time clock circuit. There is a danger
of explosion if battery is incorrectly replaced.
Replace only with same or equivalent type
recommended by the manufacturer. Discard
used batteries according to manufacturer’s
instructions.
1 2
1 2

CNCN
CN13CN
MIO-3360 Startup Manual 3
MIO-3360 Connector Locations
Figure 1: MIO-3360 Connector Locations (Top Side)
Figure 2: MIO-3360 Connector Locations (Bottom Side)
CN 34
CN5
CN10
CN1 1
CN4
CN18
CN29
MIO-3360 Connector Location (Bottom Side)

Unit: mm
Unit: mm
4 MIO-3360 Startup Manual
Figure 3: MIO-3360 Mechanical Drawing (Top Side)
Figure 4: MIO-3360 Mechanical Drawing (Bottom Side)
Mechanical drawing
(Bottom view)
Mechanical drawing
(Top view)
Mechanical drawing
(Bottom view)
Mechanical drawing
(Top view)
MIO-3360 Mechanical Drawing

MIO-3360 Startup Manual 5
MIO-3360 Mechanical Drawing
Figure 5: MIO-3360 Mechanical Drawing (Side View)
Figure 6: MIO-3360 Mechanical Drawing (Side View with Heat Sink)
Mechanical drawing
(side view with Heat sink)
Mechanical drawing
(side view)
Mechanical drawing
(side view with Heat sink)
Mechanical drawing
(side view)
Unit: mm
Unit: mm